09-21-2021, 03:06 PM
I have flashed the latest image from manjaro for quartz github repo, and got as far as getting an output on UART, but it remains stuck while booting the kernel...
I have a jumper on ON/OFF_BAT pins, and get stuck on the following:
Disk: /dev/sda
Size: 29.12 GiB, 31268536320 bytes, 61071360 sectors
Label: gpt, identifier: 8551F660-0661-4597-8AF9-EA3B6AFC5F42
Device Start End Sectors Size Type
>> Free space 2048 16383 14336 7M
/dev/sda1 16384 30719 14336 7M Microsoft basic data
Free space 30720 62499 31780 15.5M
/dev/sda2 62500 500000 437501 213.6M EFI System
/dev/sda3 500001 3291102 2791102 1.3G Linux filesystem
Free space 3291136 61071326 57780191 27.6G
Jumping to U-Boot(0x00a00000) via ARM Trusted Firmware(0x00)
Total: 218.346 ms
INFO: Preloader serial: 2
NOTICE: BL31: v2.3():v2.3-135-gcda1658bc-dirty:xsf
NOTICE: BL31: Built : 19:32:20, Jun 2 2021
INFO: GICv3 without legacyr initialized in EL3
INFO: pmu v1 is valid
INFO: dfs DDReq_mhz= 1056MHz
INFO: dfs DDR fsp_param[1].freq_mhz= 324MHz
INFO: dfs DDR fsp_param[2].f dfs DDR fsp_param[3].freq_mhz= 780MHz
INFO: Using opteed sec cpu_context!
INFO: boot INFO: BL31: Initializing runtime services
INFO: BL31: Initializing BL32
I/TC:
I/TC: Start rockchip platform init
I/TC: Rockchip release version: 1.0
I/TC: OP-TEE ve 2021 aarch64
I/TC: Initialized
INFO: BL31: Preparing for E to normal world
INFO: Entry point address = 0xa00000
INFO: SPSR = 0x3c9
U-Boot 2017.09 (Jun 26 2021 - 13:03:27 +0000)
Model: PineRK3566 Quartz64 Board
PreSerial: 2, raw, 0xfe660000
DRAM: 7.7 GiB
Sysmem: init
Relocation Offset: ed39f000, fdt: eb9f9fbdwmmc@fe2b0000: 1, dwmmc@fe2c0000: 2, sdhci@fe310000: 0
Bootdev(atags): mmc 0
MMC0: HS200, 200Mhz
PartType: EFI
No misc partition
boot mode: None
FIT: No boot partition
No r
Failed to load DTB
Failed to get kernel dtb, ret=-19
io-domain: OK
MMC error: The cmd index is 1, ret is -110
Card did not respondct!
mmc_init: -95, time 10
** Bad device mmc 1 **
Using default environment
Model: Pine64 RK3566 Quartz64 Board
rockchip_set_serialno: could not find efuse/otp device
CLK: (syarm: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
apll 816000 KHz
dpll 528000 KHz
gp npll 24000 KHz
vpll 24000 KHz
hpll 24000 KHz
ppll 100000 KHz
armclk 816000 KHz
aclk_bus 150000 KHz
pclk_bus 5KHz
aclk_top_high 300000 KHz
aclk_top_low 200000 KHz
hclk_top 150000 KHz
pclk_top 50hclk_perimid 150000 KHz
pclk_pmu 50000 KHz
Net: clk_get_by_name(master_bus) failed: -22eqo failed: -22No ethernet found.
Hit key to stop autoboot('CTRL+C'): 0
## Booting FIT Image FIT: No boot partition
FIT: No FIartition
ANDROID: reboot reason: "(none)"
optee api revision: 2.0
TEEC: Waring: Could not find security partition
Not AVB images, AVB skip
android_image_lot find part: boot
Android image load failed
Android boot failed, error -1.
MMC error: The cmd index is 1, ret is -110
Card did not respond
mmc0(part 0) is current device
Scanning mmc 0:2...
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinreading /extlinux/extlinux.conf
285 bytes read in 15 ms (18.6 Ki Manjaro ARM
Retrieving file: /initramfs-linux.img
reading /initramfs-linux.img
7788335 bytes read in 59 ms (125.9 MiB/s)
Retrieving file: /Imareading /Image
29518336 bytes read in 187 ms (150.5 MiB/s)
append: initrd=/initramfs-linux.img root=PARTUUID=d35c868c-5a33-4bae-b2f6-f0cb5b2aac3a rw earlycon=uart8250,mmio32,,1500000n8 s
Retrieving file: /dtbs/rockchip/rk3566-reading /dtbs/rockchip/rk3566-quartz64-a.dtb
104865 bytes read in 28 ms (3.6 MiB/s)
Fdt Ramdisk skip relocation
## Flattened Device Tree blob at 0x0a100000
Booting using the fdt blob at 0x0a100000
Using Device Tree in place at 000000000a100000, end 000000000a11c9a0
can't found rockchip,drm-logo, use rockchip,fb-logo
WARNING: could not set reg FDT_ERR_BADOFFSET.
failed to reserve fb-loader-logo memory
Adding bank: 0x00200000 - 0x08400000 (sisize: 0xe6c00000)
Adding bank: 0x100000000 - 0x200000000 (size: 0x100000000)
Total: 786.452 ms
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[ 0.000000] Linux verGCC) 10.2.0, GNU ld (GNU Binutils) 2.35) #1 SMP PREEMPT Fri Sep 17 12:52:46 UTC 2021
[ 0.000ne64 RK3566 Quartz64-A Board
[ 0.000000] earlycon: uart8250 000] printk: bootconsole [uart8250] enabled
[ 3.048209] rockchip-usb2phy fe8a0000.usb2-phy: failed to cre[ 3.067859] arm-scmi firmwarecmi: Failed. SCMI protocol 2e
[ 3.496594] arm-scmi firmwarecmi: Failed. SCMI protocol 19 not active.
[ 3.499908] arm-scmi firmwarecmi: Failed. SCMI protocol 17 [ 3.561017] rockchip-dw-pcie 3c0000000.pcie: invalid resour)
Starting version 249.4-1-arch
----
and then nothing anymore... Am I missing something? I would expect to get a prompt after a while, or something. thx!
I have a jumper on ON/OFF_BAT pins, and get stuck on the following:
Disk: /dev/sda
Size: 29.12 GiB, 31268536320 bytes, 61071360 sectors
Label: gpt, identifier: 8551F660-0661-4597-8AF9-EA3B6AFC5F42
Device Start End Sectors Size Type
>> Free space 2048 16383 14336 7M
/dev/sda1 16384 30719 14336 7M Microsoft basic data
Free space 30720 62499 31780 15.5M
/dev/sda2 62500 500000 437501 213.6M EFI System
/dev/sda3 500001 3291102 2791102 1.3G Linux filesystem
Free space 3291136 61071326 57780191 27.6G
Jumping to U-Boot(0x00a00000) via ARM Trusted Firmware(0x00)
Total: 218.346 ms
INFO: Preloader serial: 2
NOTICE: BL31: v2.3():v2.3-135-gcda1658bc-dirty:xsf
NOTICE: BL31: Built : 19:32:20, Jun 2 2021
INFO: GICv3 without legacyr initialized in EL3
INFO: pmu v1 is valid
INFO: dfs DDReq_mhz= 1056MHz
INFO: dfs DDR fsp_param[1].freq_mhz= 324MHz
INFO: dfs DDR fsp_param[2].f dfs DDR fsp_param[3].freq_mhz= 780MHz
INFO: Using opteed sec cpu_context!
INFO: boot INFO: BL31: Initializing runtime services
INFO: BL31: Initializing BL32
I/TC:
I/TC: Start rockchip platform init
I/TC: Rockchip release version: 1.0
I/TC: OP-TEE ve 2021 aarch64
I/TC: Initialized
INFO: BL31: Preparing for E to normal world
INFO: Entry point address = 0xa00000
INFO: SPSR = 0x3c9
U-Boot 2017.09 (Jun 26 2021 - 13:03:27 +0000)
Model: PineRK3566 Quartz64 Board
PreSerial: 2, raw, 0xfe660000
DRAM: 7.7 GiB
Sysmem: init
Relocation Offset: ed39f000, fdt: eb9f9fbdwmmc@fe2b0000: 1, dwmmc@fe2c0000: 2, sdhci@fe310000: 0
Bootdev(atags): mmc 0
MMC0: HS200, 200Mhz
PartType: EFI
No misc partition
boot mode: None
FIT: No boot partition
No r
Failed to load DTB
Failed to get kernel dtb, ret=-19
io-domain: OK
MMC error: The cmd index is 1, ret is -110
Card did not respondct!
mmc_init: -95, time 10
** Bad device mmc 1 **
Using default environment
Model: Pine64 RK3566 Quartz64 Board
rockchip_set_serialno: could not find efuse/otp device
CLK: (syarm: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
apll 816000 KHz
dpll 528000 KHz
gp npll 24000 KHz
vpll 24000 KHz
hpll 24000 KHz
ppll 100000 KHz
armclk 816000 KHz
aclk_bus 150000 KHz
pclk_bus 5KHz
aclk_top_high 300000 KHz
aclk_top_low 200000 KHz
hclk_top 150000 KHz
pclk_top 50hclk_perimid 150000 KHz
pclk_pmu 50000 KHz
Net: clk_get_by_name(master_bus) failed: -22eqo failed: -22No ethernet found.
Hit key to stop autoboot('CTRL+C'): 0
## Booting FIT Image FIT: No boot partition
FIT: No FIartition
ANDROID: reboot reason: "(none)"
optee api revision: 2.0
TEEC: Waring: Could not find security partition
Not AVB images, AVB skip
android_image_lot find part: boot
Android image load failed
Android boot failed, error -1.
MMC error: The cmd index is 1, ret is -110
Card did not respond
mmc0(part 0) is current device
Scanning mmc 0:2...
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinreading /extlinux/extlinux.conf
285 bytes read in 15 ms (18.6 Ki Manjaro ARM
Retrieving file: /initramfs-linux.img
reading /initramfs-linux.img
7788335 bytes read in 59 ms (125.9 MiB/s)
Retrieving file: /Imareading /Image
29518336 bytes read in 187 ms (150.5 MiB/s)
append: initrd=/initramfs-linux.img root=PARTUUID=d35c868c-5a33-4bae-b2f6-f0cb5b2aac3a rw earlycon=uart8250,mmio32,,1500000n8 s
Retrieving file: /dtbs/rockchip/rk3566-reading /dtbs/rockchip/rk3566-quartz64-a.dtb
104865 bytes read in 28 ms (3.6 MiB/s)
Fdt Ramdisk skip relocation
## Flattened Device Tree blob at 0x0a100000
Booting using the fdt blob at 0x0a100000
Using Device Tree in place at 000000000a100000, end 000000000a11c9a0
can't found rockchip,drm-logo, use rockchip,fb-logo
WARNING: could not set reg FDT_ERR_BADOFFSET.
failed to reserve fb-loader-logo memory
Adding bank: 0x00200000 - 0x08400000 (sisize: 0xe6c00000)
Adding bank: 0x100000000 - 0x200000000 (size: 0x100000000)
Total: 786.452 ms
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[ 0.000000] Linux verGCC) 10.2.0, GNU ld (GNU Binutils) 2.35) #1 SMP PREEMPT Fri Sep 17 12:52:46 UTC 2021
[ 0.000ne64 RK3566 Quartz64-A Board
[ 0.000000] earlycon: uart8250 000] printk: bootconsole [uart8250] enabled
[ 3.048209] rockchip-usb2phy fe8a0000.usb2-phy: failed to cre[ 3.067859] arm-scmi firmwarecmi: Failed. SCMI protocol 2e
[ 3.496594] arm-scmi firmwarecmi: Failed. SCMI protocol 19 not active.
[ 3.499908] arm-scmi firmwarecmi: Failed. SCMI protocol 17 [ 3.561017] rockchip-dw-pcie 3c0000000.pcie: invalid resour)
Starting version 249.4-1-arch
----
and then nothing anymore... Am I missing something? I would expect to get a prompt after a while, or something. thx!