Lakka test boot-up Rock64.arm-8.1.2 dmesg logfile
#1
Information 
Code:
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.4.83 (demetris@Server01) (gcc version 6.3.1 20170404 (Linaro GCC 6.3-2017.05) ) #1 SMP Fri Sep 29 10:33:18 CDT 2017
[    0.000000] Boot CPU: AArch64 Processor [410fd034]
[    0.000000] On node 0 totalpages: 1043968
[    0.000000]   DMA zone: 16312 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 1043968 pages, LIFO batch:31
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] PERCPU: Embedded 21 pages/cpu @ffffffc0fef38000 s45864 r8192 d31960 u86016
[    0.000000] pcpu-alloc: s45864 r8192 d31960 u86016 alloc=21*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: enabling workaround for ARM erratum 845719
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 1027656
[    0.000000] Kernel command line: root=/dev/ram0 rdinit=/init BOOT_IMAGE=/Image usbcore.autosuspend=-1 earlyprintk console=ttyFIQ0 console=tty0 boot=UUID=2909-2628 disk=UUID=11c779c3-8cfd-4e31-943e-58321082a130 textmode ssh
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.000000] software IO TLB [mem 0xf6400000-0xfa400000] (64MB) mapped at [ffffffc0f6400000-ffffffc0fa3fffff]
[    0.000000] Memory: 4020164K/4175872K available (8894K kernel code, 1296K rwdata, 3416K rodata, 2880K init, 648K bss, 155708K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
[    0.000000]     vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000   (   246 GB)
[    0.000000]       .init : 0xffffff8008c90000 - 0xffffff8008f60000   (  2880 KB)
[    0.000000]       .text : 0xffffff8008080000 - 0xffffff8008930000   (  8896 KB)
[    0.000000]     .rodata : 0xffffff8008930000 - 0xffffff8008c90000   (  3456 KB)
[    0.000000]       .data : 0xffffff8008f60000 - 0xffffff80090a4008   (  1297 KB)
[    0.000000]     vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000   (     8 GB maximum)
[    0.000000]               0xffffffbdc0008000 - 0xffffffbdc3fc0000   (    63 MB actual)
[    0.000000]     fixed   : 0xffffffbffe7fd000 - 0xffffffbffec00000   (  4108 KB)
[    0.000000]     PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000   (    16 MB)
[    0.000000]     memory  : 0xffffffc000200000 - 0xffffffc0ff000000   (  4078 MB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]     Build-time adjustment of leaf fanout to 64.
[    0.000000] NR_IRQS:64 nr_irqs:64 0
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000832] Console: colour dummy device 80x25
[    0.002166] console [tty0] enabled
[    0.002214] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[    0.002284] pid_max: default: 32768 minimum: 301
[    0.002472] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.002519] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.003499] Initializing cgroup subsys io
[    0.003549] Initializing cgroup subsys memory
[    0.003611] Initializing cgroup subsys devices
[    0.003655] Initializing cgroup subsys freezer
[    0.003697] Initializing cgroup subsys pids
[    0.003755] ftrace: allocating 34156 entries in 134 pages
[    0.092162] sched-energy: CPU device node has no sched-energy-costs
[    0.092216] Invalid sched_group_energy for CPU0
[    0.092250] CPU0: update cpu_capacity 1024
[    0.092340] ASID allocator initialised with 65536 entries
[    0.097199] Detected VIPT I-cache on CPU1
[    0.097258] Invalid sched_group_energy for CPU1
[    0.097264] CPU1: update cpu_capacity 1024
[    0.097269] CPU1: Booted secondary processor [410fd034]
[    0.097925] Detected VIPT I-cache on CPU2
[    0.097972] Invalid sched_group_energy for CPU2
[    0.097978] CPU2: update cpu_capacity 1024
[    0.097983] CPU2: Booted secondary processor [410fd034]
[    0.098667] Detected VIPT I-cache on CPU3
[    0.098711] Invalid sched_group_energy for CPU3
[    0.098716] CPU3: update cpu_capacity 1024
[    0.098721] CPU3: Booted secondary processor [410fd034]
[    0.098822] Brought up 4 CPUs
[    0.099197] SMP: Total of 4 processors activated.
[    0.099239] CPU: All CPU(s) started at EL2
[    0.099303] alternatives: patching kernel code
[    0.099537] Invalid sched_group_energy for CPU3
[    0.099574] Invalid sched_group_energy for Cluster3
[    0.099608] Invalid sched_group_energy for CPU2
[    0.099642] Invalid sched_group_energy for Cluster2
[    0.099676] Invalid sched_group_energy for CPU1
[    0.099710] Invalid sched_group_energy for Cluster1
[    0.099743] Invalid sched_group_energy for CPU0
[    0.099777] Invalid sched_group_energy for Cluster0
[    0.100531] devtmpfs: initialized
[    0.116323] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    0.116415] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.116993] pinctrl core: initialized pinctrl subsystem
[    0.117377] regulator-dummy: no parameters
[    0.118261] NET: Registered protocol family 16
[    0.132123] cpuidle: using governor ladder
[    0.145482] cpuidle: using governor menu
[    0.145536] Registered FIQ tty driver
[    0.146038] vdso: 2 pages (1 code @ ffffff8008936000, 1 data @ ffffff8008f64000)
[    0.146131] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.146315] DMA: preallocated 256 KiB pool for atomic allocations
[    0.159508] gpiochip_add: registered GPIOs 1000 to 1031 on device: gpio0
[    0.159648] gpiochip_add: registered GPIOs 1032 to 1063 on device: gpio1
[    0.159775] gpiochip_add: registered GPIOs 1064 to 1095 on device: gpio2
[    0.159910] gpiochip_add: registered GPIOs 1096 to 1127 on device: gpio3
[    0.169031] genirq: Setting trigger mode 8 for irq 176 failed (gic_set_type+0x0/0x64)
[    0.219554] console [ttyFIQ0] enabled
[    0.220215] Registered fiq debugger ttyFIQ0
[    0.234193] mpp venc_srv: mpp_probe enter
[    0.234651] mpp venc_srv: init success
[    0.235647] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/vcc-phy-regulator[0]'
[    0.235683] vcc_phy: no parameters
[    0.235916] reg-fixed-voltage vcc-phy-regulator: vcc_phy supplying 0uV
[    0.236184] of_get_named_gpiod_flags: parsed 'gpio' property of node '/sdmmc-regulator[0]' - status (0)
[    0.236249] reg-fixed-voltage sdmmc-regulator: Looking up vin-supply from device tree
[    0.236271] vcc_sd: unable to resolve supply
[    0.236286] vcc_sd: 3300 mV
[    0.236505] reg-fixed-voltage sdmmc-regulator: Looking up vin-supply from device tree
[    0.236526] vcc_sd: unable to resolve supply
[    0.236544] reg-fixed-voltage sdmmc-regulator: vcc_sd supplying 3300000uV
[    0.236627] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/vcc-sys[0]'
[    0.236655] vcc_sys: 5000 mV
[    0.236856] reg-fixed-voltage sdmmc-regulator: Looking up vin-supply from device tree
[    0.236877] vcc_sd: unable to resolve supply
[    0.236895] reg-fixed-voltage vcc-sys: vcc_sys supplying 5000000uV
[    0.237488] iommu: Adding device ff350000.vpu-service to group 0
[    0.238180] iommu: Adding device ff360000.rkvdec to group 1
[    0.238773] iommu: Adding device ff330000.h265e to group 2
[    0.239372] iommu: Adding device ff340000.vepu to group 3
[    0.239956] iommu: Adding device ff370000.vop to group 4
[    0.241574] rk_iommu ff330200.iommu: can't get aclk
[    0.242055] rk_iommu ff330200.iommu: can't get hclk
[    0.243508] SCSI subsystem initialized
[    0.244169] usbcore: registered new interface driver usbfs
[    0.244762] usbcore: registered new interface driver hub
[    0.245394] usbcore: registered new device driver usb
[    0.246064] Linux cec interface: v0.10
[    0.246511] pps_core: LinuxPPS API ver. 1 registered
[    0.246987] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.247865] PTP clock support registered
[    0.249912] Advanced Linux Sound Architecture Driver Initialized.
[    0.251263] Bluetooth: Core ver 2.21
[    0.251652] NET: Registered protocol family 31
[    0.252111] Bluetooth: HCI device and connection manager initialized
[    0.252710] Bluetooth: HCI socket layer initialized
[    0.253179] Bluetooth: L2CAP socket layer initialized
[    0.253683] Bluetooth: SCO socket layer initialized
[    0.254563] cfg80211: World regulatory domain updated:
[    0.255050] cfg80211:  DFS Master region: unset
[    0.255471] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[    0.256404] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[    0.257161] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[    0.258038] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[    0.258793] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[    0.259698] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[    0.260588] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[    0.261352] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[    0.262105] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[    0.263360] rockchip-cpuinfo cpuinfo: Serial        : bbc99184ba566da9
[    0.264822] clocksource: Switched to clocksource arch_sys_counter
[    0.337887] FS-Cache: Loaded
[    0.352060] NET: Registered protocol family 2
[    0.353133] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[    0.354287] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes)
[    0.356449] TCP: Hash tables configured (established 32768 bind 32768)
[    0.357172] UDP hash table entries: 2048 (order: 5, 196608 bytes)
[    0.357997] UDP-Lite hash table entries: 2048 (order: 5, 196608 bytes)
[    0.359188] NET: Registered protocol family 1
[    0.360076] RPC: Registered named UNIX socket transport module.
[    0.360637] RPC: Registered udp transport module.
[    0.361087] RPC: Registered tcp transport module.
[    0.361580] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.362253] PCI: CLS 0 bytes, default 64
[    0.495750] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[    0.514780] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.516530] FS-Cache: Netfs 'nfs' registered for caching
[    0.517711] NFS: Registering the id_resolver key type
[    0.518258] Key type id_resolver registered
[    0.518664] Key type id_legacy registered
[    0.519073] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.520027] FS-Cache: Netfs 'cifs' registered for caching
[    0.527387] NET: Registered protocol family 38
[    0.527866] Key type asymmetric registered
[    0.528297] Asymmetric key parser 'x509' registered
[    0.529060] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    0.529987] io scheduler noop registered
[    0.530386] io scheduler deadline registered
[    0.530848] io scheduler cfq registered (default)
[    0.532638] phy phy-ff450000.syscon:usb2-phy@100.0: Looking up phy-supply from device tree
[    0.532662] phy phy-ff450000.syscon:usb2-phy@100.0: Looking up phy-supply property in node /syscon@ff450000/usb2-phy@100/host-port failed
[    0.533106] phy phy-ff450000.syscon:usb2-phy@100.1: Looking up phy-supply from device tree
[    0.533127] phy phy-ff450000.syscon:usb2-phy@100.1: Looking up phy-supply property in node /syscon@ff450000/usb2-phy@100/otg-port failed
[    0.533472] rockchip-usb2phy ff450000.syscon:usb2-phy@100: GPIO lookup for consumer otg-vbus
[    0.533489] rockchip-usb2phy ff450000.syscon:usb2-phy@100: using device tree for GPIO lookup
[    0.533528] of_get_named_gpiod_flags: parsed 'otg-vbus-gpios' property of node '/syscon@ff450000/usb2-phy@100[0]' - status (0)
[    0.534224] rockchip-u3phy ff470000.usb3-phy: GPIO lookup for consumer vbus-drv
[    0.534242] rockchip-u3phy ff470000.usb3-phy: using device tree for GPIO lookup
[    0.534275] of_get_named_gpiod_flags: parsed 'vbus-drv-gpios' property of node '/usb3-phy@ff470000[0]' - status (0)
[    0.534678] phy phy-ff470000.usb3-phy.2: Looking up phy-supply from device tree
[    0.534698] phy phy-ff470000.usb3-phy.2: Looking up phy-supply property in node /usb3-phy@ff470000/utmi@ff470000 failed
[    0.535133] phy phy-ff470000.usb3-phy.3: Looking up phy-supply from device tree
[    0.535153] phy phy-ff470000.usb3-phy.3: Looking up phy-supply property in node /usb3-phy@ff470000/pipe@ff478000 failed
[    0.537505] rockchip-u3phy ff470000.usb3-phy: Rockchip u3phy initialized successfully
[    0.538755] phy phy-ff430000.hdmiphy.4: Looking up phy-supply from device tree
[    0.538776] phy phy-ff430000.hdmiphy.4: Looking up phy-supply property in node /hdmiphy@ff430000 failed
[    0.541518] rk-vcodec ff350000.vpu-service: probe device
[    0.542063] rk-vcodec ff350000.vpu-service: vpu mmu dec ffffffc0f5dea010
[    0.542965] rk-vcodec ff350000.vpu-service: allocator is drm
[    0.543579] rk-vcodec ff350000.vpu-service: checking hw id 0
[    0.544654] rk-vcodec ff350000.vpu-service: init success
[    0.545997] rk-vcodec ff360000.rkvdec: probe device
[    0.546504] rk-vcodec ff360000.rkvdec: vpu mmu dec ffffffc0f5dea810
[    0.547357] rk-vcodec ff360000.rkvdec: allocator is drm
[    0.547930] rk-vcodec ff360000.rkvdec: checking hw id 3410
[    0.549023] rk-vcodec ff360000.rkvdec: init success
[    0.549970] probe device ff330000.h265e
[    0.550663] mpp_dev ff330000.h265e: try to get iommu dev ffffffc0f5deb010
[    0.551738] mpp_dev ff330000.h265e: resource ready, register device
[    0.552651] probe device ff340000.vepu
[    0.553316] mpp_dev ff340000.vepu: try to get iommu dev ffffffc0f5deb810
[    0.554238] rockchip_mpp_vepu_reset_init:143: No aclk reset resource define
[    0.554926] rockchip_mpp_vepu_reset_init:148: No hclk reset resource define
[    0.555576] mpp_dev ff340000.vepu: resource ready, register device
[    0.559193] dma-pl330 ff1f0000.dmac: Loaded driver for PL330 DMAC-241330
[    0.559833] dma-pl330 ff1f0000.dmac:     DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
[    0.561601] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.564705] [drm:drm_core_init] Initialized drm 1.1.0 20060810
[    0.568449] rockchip-vop ff370000.vop: failed to get vop register byname
[    0.569120] rockchip-vop ff370000.vop: invalid resource
[    0.569621] rockchip-vop ff370000.vop: failed to get vop lut registers
[    0.570234] rockchip-vop ff370000.vop: invalid resource
[    0.570733] rockchip-vop ff370000.vop: failed to get vop cabc lut registers
[    0.571651] rockchip-drm display-subsystem: bound ff370000.vop (ops 0xffffff80089bfb08)
[    0.572770] i2c i2c-4: of_i2c: modalias failure on /hdmi@ff3c0000/ports
[    0.573395] dwhdmi-rockchip ff3c0000.hdmi: registered DesignWare HDMI I2C bus driver
[    0.574206] dwhdmi-rockchip ff3c0000.hdmi: Detected HDMI TX controller v2.11a with HDCP (inno_dw_hdmi_phy2)
[    0.576154] rockchip-drm display-subsystem: bound ff3c0000.hdmi (ops 0xffffff80089ba418)
[    0.576937] [drm:drm_vblank_init] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    0.577691] [drm:drm_vblank_init] No driver support for vblank timestamp query.
[    0.578556] rockchip-drm display-subsystem: failed to parse display resources
[    1.231606] Console: switching to colour frame buffer device 160x45
[    1.254472] rockchip-drm display-subsystem: fb0:  frame buffer device
[    1.259237] Registered IR keymap rc-cec
[    1.260318] input: RC for dw_hdmi as /devices/platform/ff3c0000.hdmi/rc/rc0/input0
[    1.261287] rc0: RC for dw_hdmi as /devices/platform/ff3c0000.hdmi/rc/rc0
[    1.262661] Unable to detect cache hierarchy from DT for CPU 0
[    1.264580] brd: module loaded
[    1.273524] loop: module loaded
[    1.275028] zram: Added device: zram0
[    1.275847] lkdtm: No crash points registered, enable through debugfs
[    1.276893] Loading iSCSI transport class v2.0-870.
[    1.277978] iscsi: registered transport (tcp)
[    1.280018] rockchip-spi ff190000.spi: Failed to request TX DMA channel
[    1.280879] rockchip-spi ff190000.spi: Failed to request RX DMA channel
[    1.282647] m25p80 spi32766.0: gd25q128 (16384 Kbytes)
[    1.283362] 6 ofpart partitions found on MTD device spi32766.0
[    1.284098] Creating 6 MTD partitions on "spi32766.0":
[    1.284756] 0x000000000000-0x000000008000 : "system"
[    1.285914] 0x000000008000-0x000000400000 : "loader"
[    1.286982] 0x000000400000-0x0000007c0000 : "reserved"
[    1.288057] 0x0000007c0000-0x000000800000 : "vendor"
[    1.297192] 0x000000800000-0x000000c00000 : "uboot"
[    1.306211] 0x000000c00000-0x000001000000 : "atf"
[    1.316664] rk_gmac-dwmac ff540000.ethernet: Looking up phy-supply from device tree
[    1.316788] rk_gmac-dwmac ff540000.ethernet: clock input or output? (input).
[    1.325494] rk_gmac-dwmac ff540000.ethernet: TX delay(0x26).
[    1.333886] rk_gmac-dwmac ff540000.ethernet: RX delay(0x11).
[    1.342114] rk_gmac-dwmac ff540000.ethernet: integrated PHY? (no).
[    1.350567] rk_gmac-dwmac ff540000.ethernet: clock input from PHY
[    1.363789] rk_gmac-dwmac ff540000.ethernet: init for RGMII
[    1.371985] stmmac - user ID: 0x10, Synopsys ID: 0x35
[    1.380069]  Ring mode enabled
[    1.387862]  DMA HW capability register supported
[    1.388460]  Normal descriptors
[    1.403380]  RX Checksum Offload Engine supported (type 2)
[    1.411206]  TX Checksum insertion supported
[    1.418765]  Wake-Up On Lan supported
[    1.426262]  Enable RX Mitigation via HW Watchdog Timer
[    1.433950] of_get_named_gpiod_flags: parsed 'snps,reset-gpio' property of node '/ethernet@ff540000[0]' - status (0)
[    1.506985] libphy: stmmac: probed
[    1.514193] eth%d: PHY ID 001cc916 at 0 IRQ POLL (stmmac-0:00) active
[    1.521650] eth%d: PHY ID 001cc916 at 1 IRQ POLL (stmmac-0:01)
[    1.530074] usbcore: registered new interface driver rndis_wlan
[    1.537494] Rockchip WiFi SYS interface (V1.00) ...
[    1.544636] usbcore: registered new interface driver rtl8150
[    1.551698] usbcore: registered new interface driver r8152
[    1.558564] usbcore: registered new interface driver asix
[    1.565228] usbcore: registered new interface driver ax88179_178a
[    1.571817] usbcore: registered new interface driver cdc_ether
[    1.578262] usbcore: registered new interface driver rndis_host
[    1.584562] usbcore: registered new interface driver cdc_ncm
[    1.590614] usbcore: registered new interface driver cdc_mbim
[    1.598327] phy phy-ff470000.usb3-phy.2: u3phy u2 power on
[    1.604228] phy phy-ff470000.usb3-phy.3: u3phy u3 power on
[    1.611002] dwc2 ff580000.usb: Looking up vusb_d-supply from device tree
[    1.611024] dwc2 ff580000.usb: Looking up vusb_d-supply property in node /usb@ff580000 failed
[    1.611042] ff580000.usb supply vusb_d not found, using dummy regulator
[    1.617146] dwc2 ff580000.usb: Looking up vusb_a-supply from device tree
[    1.617167] dwc2 ff580000.usb: Looking up vusb_a-supply property in node /usb@ff580000 failed
[    1.617183] ff580000.usb supply vusb_a not found, using dummy regulator
[    1.851734] dwc2 ff580000.usb: DWC OTG Controller
[    1.857430] dwc2 ff580000.usb: new USB bus registered, assigned bus number 1
[    1.863408] dwc2 ff580000.usb: irq 40, io mem 0x00000000
[    1.869370] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.875408] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.881451] usb usb1: Product: DWC OTG Controller
[    1.887196] usb usb1: Manufacturer: Linux 4.4.83 dwc2_hsotg
[    1.893021] usb usb1: SerialNumber: ff580000.usb
[    1.899561] hub 1-0:1.0: USB hub found
[    1.905278] hub 1-0:1.0: 1 port detected
[    1.912329] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.918553] ehci-pci: EHCI PCI platform driver
[    1.924644] ehci-platform: EHCI generic platform driver
[    1.933406] ehci-platform ff5c0000.usb: EHCI Host Controller
[    1.939877] ehci-platform ff5c0000.usb: new USB bus registered, assigned bus number 2
[    1.946502] ehci-platform ff5c0000.usb: irq 41, io mem 0xff5c0000
[    1.961529] ehci-platform ff5c0000.usb: USB 2.0 started, EHCI 1.00
[    1.968209] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    1.974786] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.981487] usb usb2: Product: EHCI Host Controller
[    1.987909] usb usb2: Manufacturer: Linux 4.4.83 ehci_hcd
[    1.994379] usb usb2: SerialNumber: ff5c0000.usb
[    2.001600] hub 2-0:1.0: USB hub found
[    2.007942] hub 2-0:1.0: 1 port detected
[    2.014875] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.021467] ohci-platform: OHCI generic platform driver
[    2.028469] ohci-platform ff5d0000.usb: Generic Platform OHCI controller
[    2.035445] ohci-platform ff5d0000.usb: new USB bus registered, assigned bus number 3
[    2.042394] ohci-platform ff5d0000.usb: irq 42, io mem 0xff5d0000
[    2.105762] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    2.112597] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.119408] usb usb3: Product: Generic Platform OHCI controller
[    2.126090] usb usb3: Manufacturer: Linux 4.4.83 ohci_hcd
[    2.132684] usb usb3: SerialNumber: ff5d0000.usb
[    2.140079] hub 3-0:1.0: USB hub found
[    2.146739] hub 3-0:1.0: 1 port detected
[    2.154515] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[    2.161823] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 4
[    2.169329] xhci-hcd xhci-hcd.9.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x00210010
[    2.176933] xhci-hcd xhci-hcd.9.auto: irq 180, io mem 0xff600000
[    2.184506] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[    2.191977] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.199627] usb usb4: Product: xHCI Host Controller
[    2.206993] usb usb4: Manufacturer: Linux 4.4.83 xhci-hcd
[    2.207002] usb usb4: SerialNumber: xhci-hcd.9.auto
[    2.207847] hub 4-0:1.0: USB hub found
[    2.207894] hub 4-0:1.0: 1 port detected
[    2.208412] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[    2.208682] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 5
[    2.208792] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.208970] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003
[    2.208981] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.208990] usb usb5: Product: xHCI Host Controller
[    2.208998] usb usb5: Manufacturer: Linux 4.4.83 xhci-hcd
[    2.209006] usb usb5: SerialNumber: xhci-hcd.9.auto
[    2.209795] hub 5-0:1.0: USB hub found
[    2.209838] hub 5-0:1.0: 1 port detected
[    2.210534] usbcore: registered new interface driver cdc_acm
[    2.210539] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    2.210611] usbcore: registered new interface driver cdc_wdm
[    2.210689] usbcore: registered new interface driver uas
[    2.210925] usbcore: registered new interface driver usb-storage
[    2.211059] usbcore: registered new interface driver usbserial
[    2.211113] usbcore: registered new interface driver usbserial_generic
[    2.211155] usbserial: USB Serial support registered for generic
[    2.211225] usbcore: registered new interface driver cp210x
[    2.211272] usbserial: USB Serial support registered for cp210x
[    2.211404] usbcore: registered new interface driver ftdi_sio
[    2.211446] usbserial: USB Serial support registered for FTDI USB Serial Device
[    2.211926] usbcore: registered new interface driver keyspan
[    2.211973] usbserial: USB Serial support registered for Keyspan - (without firmware)
[    2.212015] usbserial: USB Serial support registered for Keyspan 1 port adapter
[    2.212056] usbserial: USB Serial support registered for Keyspan 2 port adapter
[    2.212098] usbserial: USB Serial support registered for Keyspan 4 port adapter
[    2.212190] usbcore: registered new interface driver option
[    2.212238] usbserial: USB Serial support registered for GSM modem (1-port)
[    2.212782] usbcore: registered new interface driver oti6858
[    2.212824] usbserial: USB Serial support registered for oti6858
[    2.212899] usbcore: registered new interface driver pl2303
[    2.212942] usbserial: USB Serial support registered for pl2303
[    2.213033] usbcore: registered new interface driver qcserial
[    2.213081] usbserial: USB Serial support registered for Qualcomm USB modem
[    2.213200] usbcore: registered new interface driver sierra
[    2.213242] usbserial: USB Serial support registered for Sierra USB modem
[    2.214475] usbcore: registered new interface driver iforce
[    2.214588] usbcore: registered new interface driver xpad
[    2.214840] usbcore: registered new interface driver usbtouchscreen
[    2.215457] i2c /dev entries driver
[    2.218100] rk808 1-0018: Pmic Chip id: 0x8050
[    2.219191] rk808 1-0018: source: on=0x40, off=0x00
[    2.223325] rk808 1-0018: Looking up vcc1-supply from device tree
[    2.223442] DCDC_REG1: supplied by vcc_sys
[    2.223455] vcc_sys: could not add device link regulator.4 err -2
[    2.225331] vdd_logic: 712 <--> 1450 mV at 1150 mV
[    2.225633] reg-fixed-voltage sdmmc-regulator: Looking up vin-supply from device tree
[    2.225661] vcc_sd: unable to resolve supply
[    2.225683] rk808 1-0018: Looking up vcc2-supply from device tree
[    2.225764] DCDC_REG2: supplied by vcc_sys
[    2.225775] vcc_sys: could not add device link regulator.5 err -2
[    2.227131] vdd_arm: 712 <--> 1450 mV at 1000 mV
[    2.227398] reg-fixed-voltage sdmmc-regulator: Looking up vin-supply from device tree
[    2.227420] vcc_sd: unable to resolve supply
[    2.227441] rk808 1-0018: Looking up vcc3-supply from device tree
[    2.227504] DCDC_REG3: supplied by vcc_sys
[    2.227514] vcc_sys: could not add device link regulator.6 err -2
[    2.228730] vcc_ddr: at 5000 mV
[    2.228953] reg-fixed-voltage sdmmc-regulator: Looking up vin-supply from device tree
[    2.228973] vcc_sd: unable to resolve supply
[    2.228995] rk808 1-0018: Looking up vcc4-supply from device tree
[    2.229051] DCDC_REG4: supplied by vcc_sys
[    2.229061] vcc_sys: could not add device link regulator.7 err -2
[    2.229938] vcc_io: 3300 mV
[    2.230230] reg-fixed-voltage sdmmc-regulator: Looking up vin-supply from device tree
[    2.230252] vcc_sd: supplied by vcc_io
[    2.230322] rk808 1-0018: Looking up vcc5-supply from device tree
[    2.230339] LDO_REG1: supplied by vcc_io
[    2.230349] vcc_io: could not add device link regulator.8 err -2
[    2.232677] vcc_18: 1800 mV
[    2.232938] rk808 1-0018: Looking up vcc5-supply from device tree
[    2.232957] LDO_REG2: supplied by vcc_io
[    2.232967] vcc_io: could not add device link regulator.9 err -2
[    2.235298] vcc18_emmc: 1800 mV
[    2.235594] rk808 1-0018: Looking up vcc6-supply from device tree
[    2.235691] LDO_REG3: supplied by vcc_sys
[    2.235702] vcc_sys: could not add device link regulator.10 err -2
[    2.238038] vdd_10: 1000 mV
[    2.238338] rk808 1-0018: register rk8050 regulators
[    2.238550] gpiochip_find_base: cannot find free range
[    2.238557] gpiochip_add: GPIOs -1..0 (rk8xx-gpio) failed to register
[    2.238566] rk8xx-gpio rk8xx-gpio: register rk8xx gpiochip fail: -28
[    2.238583] rk8xx-gpio: probe of rk8xx-gpio failed with error -28
[    2.240650] input: rk8xx_pwrkey as /devices/platform/ff160000.i2c/i2c-1/1-0018/input/input1
[    2.241138] rk808-rtc rk808-rtc: device is disabled
[    2.241154] rk808-rtc: probe of rk808-rtc failed with error -22
[    2.241218] rk3x-i2c ff160000.i2c: Initialized RK3xxx I2C bus at ffffff800956c000
[    2.242963] lirc_dev: IR Remote Control driver registered, major 239
[    2.242979] IR NEC protocol handler initialized
[    2.242994] IR RC5(x/sz) protocol handler initialized
[    2.243009] IR RC6 protocol handler initialized
[    2.243023] IR JVC protocol handler initialized
[    2.243037] IR Sony protocol handler initialized
[    2.243051] IR SANYO protocol handler initialized
[    2.243065] IR Sharp protocol handler initialized
[    2.243079] IR MCE Keyboard/mouse protocol handler initialized
[    2.243093] IR LIRC bridge handler initialized
[    2.243107] IR XMP protocol handler initialized
[    2.243516] of_get_named_gpiod_flags: parsed 'gpios' property of node '/ir-receiver[0]' - status (0)
[    2.243577] Registered IR keymap rc-pine64
[    2.243994] input: gpio_ir_recv as /devices/platform/ir-receiver/rc/rc1/input2
[    2.244257] rc1: gpio_ir_recv as /devices/platform/ir-receiver/rc/rc1
[    2.244713] input: MCE IR Keyboard/Mouse (gpio-rc-recv) as /devices/virtual/input/input3
[    2.245184] rc rc1: lirc_dev: driver ir-lirc-codec (gpio-rc-recv) registered at minor = 0
[    2.246207] rockchip-iodomain ff100000.syscon:io-domains: Looking up vccio1-supply from device tree
[    2.246334] rockchip-iodomain ff100000.syscon:io-domains: Looking up vccio2-supply from device tree
[    2.246921] rockchip-iodomain ff100000.syscon:io-domains: Looking up vccio3-supply from device tree
[    2.247032] rockchip-iodomain ff100000.syscon:io-domains: Looking up vccio4-supply from device tree
[    2.247589] rockchip-iodomain ff100000.syscon:io-domains: Looking up vccio5-supply from device tree
[    2.247665] rockchip-iodomain ff100000.syscon:io-domains: Looking up vccio6-supply from device tree
[    2.247736] rockchip-iodomain ff100000.syscon:io-domains: Looking up pmuio-supply from device tree
[    2.249552] rockchip-thermal ff250000.tsadc: Missing tshut mode property, using default (cru)
[    2.249564] rockchip-thermal ff250000.tsadc: Missing tshut-polarity property, using default (low)
[    2.250425] Bluetooth: Virtual HCI driver ver 1.5
[    2.250669] Bluetooth: HCI UART driver ver 2.3
[    2.250676] Bluetooth: HCI UART protocol H4 registered
[    2.250680] Bluetooth: HCI UART protocol Three-wire (H5) registered
[    2.250791] usbcore: registered new interface driver bfusb
[    2.250900] usbcore: registered new interface driver btusb
[    2.250911] Bluetooth: Generic Bluetooth SDIO driver ver 0.1
[    2.251374] cpu cpu0: leakage=12
[    2.251413] cpu cpu0: Looking up cpu-supply from device tree
[    2.252015] cpu cpu0: Looking up cpu-supply from device tree
[    2.252228] cpu cpu0: Looking up cpu-supply from device tree
[    2.254247] sdhci: Secure Digital Host Controller Interface driver
[    2.254249] sdhci: Copyright(c) Pierre Ossman
[    2.254253] Synopsys Designware Multimedia Card Interface Driver
[    2.254937] dwmmc_rockchip ff500000.rksdmmc: IDMAC supports 32-bit address mode.
[    2.254958] dwmmc_rockchip ff500000.rksdmmc: Using internal DMA controller.
[    2.254968] dwmmc_rockchip ff500000.rksdmmc: Version ID is 270a
[    2.255007] dwmmc_rockchip ff500000.rksdmmc: DW MMC controller at irq 37,32 bit host data width,256 deep fifo
[    2.255028] dwmmc_rockchip ff500000.rksdmmc: Looking up vmmc-supply from device tree
[    2.255120] dwmmc_rockchip ff500000.rksdmmc: Looking up vqmmc-supply from device tree
[    2.255178] dwmmc_rockchip ff500000.rksdmmc: GPIO lookup for consumer cd
[    2.255182] dwmmc_rockchip ff500000.rksdmmc: using device tree for GPIO lookup
[    2.255198] of_get_named_gpiod_flags: parsed 'cd-gpios' property of node '/rksdmmc@ff500000[0]' - status (0)
[    2.255224] dwmmc_rockchip ff500000.rksdmmc: Got CD GPIO
[    2.255229] dwmmc_rockchip ff500000.rksdmmc: GPIO lookup for consumer wp
[    2.255233] dwmmc_rockchip ff500000.rksdmmc: using device tree for GPIO lookup
[    2.255238] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/rksdmmc@ff500000[0]'
[    2.255243] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/rksdmmc@ff500000[0]'
[    2.255247] dwmmc_rockchip ff500000.rksdmmc: using lookup tables for GPIO lookup
[    2.255251] dwmmc_rockchip ff500000.rksdmmc: lookup for GPIO wp failed
[    2.268198] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    2.282717] dwmmc_rockchip ff500000.rksdmmc: 1 slots initialized
[    2.285275] dwmmc_rockchip ff520000.rksdmmc: IDMAC supports 32-bit address mode.
[    2.285306] dwmmc_rockchip ff520000.rksdmmc: Using internal DMA controller.
[    2.285315] dwmmc_rockchip ff520000.rksdmmc: Version ID is 270a
[    2.285359] dwmmc_rockchip ff520000.rksdmmc: DW MMC controller at irq 38,32 bit host data width,256 deep fifo
[    2.285388] dwmmc_rockchip ff520000.rksdmmc: Looking up vmmc-supply from device tree
[    2.285492] dwmmc_rockchip ff520000.rksdmmc: Looking up vqmmc-supply from device tree
[    2.286021] dwmmc_rockchip ff520000.rksdmmc: GPIO lookup for consumer wp
[    2.286026] dwmmc_rockchip ff520000.rksdmmc: using device tree for GPIO lookup
[    2.286032] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/rksdmmc@ff520000[0]'
[    2.286037] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/rksdmmc@ff520000[0]'
[    2.286041] dwmmc_rockchip ff520000.rksdmmc: using lookup tables for GPIO lookup
[    2.286046] dwmmc_rockchip ff520000.rksdmmc: lookup for GPIO wp failed
[    2.288172] usb 1-1: new high-speed USB device number 2 using dwc2
[    2.298200] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    2.310746] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[    2.310795] mmc0: new high speed SDHC card at address 59b4
[    2.311308] mmcblk0: mmc0:59b4 EB2MW 29.8 GiB
[    2.312636] dwmmc_rockchip ff520000.rksdmmc: 1 slots initialized
[    2.312754] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.314015]  mmcblk0: p1 p2
[    2.315260] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/standby-led[0]' - status (-517)
[    2.315366] ledtrig-cpu: registered to indicate activity on CPUs
[    2.315421] hidraw: raw HID events driver (C) Jiri Kosina
[    2.315743] usbcore: registered new interface driver usbhid
[    2.315745] usbhid: USB HID core driver
[    2.318481] rk3328-codec ff410000.codec: spk_depop_time use default value.
[    2.321804] NET: Registered protocol family 10
[    2.322576] NET: Registered protocol family 17
[    2.322682] Bluetooth: RFCOMM socket layer initialized
[    2.322711] Bluetooth: RFCOMM ver 1.11
[    2.322725] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    2.322732] Bluetooth: HIDP socket layer initialized
[    2.322931] [WLAN_RFKILL]: Enter rfkill_wlan_init
[    2.323056] [BT_RFKILL]: Enter rfkill_rk_init
[    2.323162] Key type dns_resolver registered
[    2.324475] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/standby-led[0]' - status (-517)
[    2.324762] of_get_named_gpiod_flags: can't parse 'simple-audio-card,hp-det-gpio' property of node '/hdmi-sound[0]'
[    2.324766] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpio' property of node '/hdmi-sound[0]'
[    2.325228] asoc-simple-card hdmi-sound: i2s-hifi <-> ff000000.i2s mapping ok
[    2.326274] of_get_named_gpiod_flags: can't parse 'simple-audio-card,hp-det-gpio' property of node '/sound[0]'
[    2.326279] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpio' property of node '/sound[0]'
[    2.328219] mmc_host mmc1: Bus speed (slot 0) = 300000Hz (slot req 300000Hz, actual 300000HZ div = 0)
[    2.346804] asoc-simple-card sound: rk3328-hifi <-> ff010000.i2s mapping ok
[    2.347246] asoc-simple-card sound: snd-soc-dummy-dai <-> ff010000.i2s mapping ok
[    2.348440] of_get_named_gpiod_flags: can't parse 'simple-audio-card,hp-det-gpio' property of node '/spdif-sound[0]'
[    2.348445] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpio' property of node '/spdif-sound[0]'
[    2.348861] asoc-simple-card spdif-sound: dit-hifi <-> ff030000.spdif mapping ok
[    2.349593] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/standby-led[0]' - status (-517)
[    2.349896] hctosys: unable to open rtc device (rtc0)
[    2.358273] mmc_host mmc1: Bus speed (slot 0) = 200000Hz (slot req 200000Hz, actual 200000HZ div = 0)
[    2.368699] rockchip-pm-domain ff100000.syscon:power-controller: failed to get ack on domain 'pd_video', val=0x10040
[    2.378723] rockchip-pm-domain ff100000.syscon:power-controller: failed to get ack on domain 'pd_vpu', val=0x10040
[    2.380485] ALSA device list:
[    2.380488]   #0: HDMI
[    2.380489]   #1: I2S
[    2.380491]   #2: SPDIF
[    2.398207] mmc_host mmc1: Bus speed (slot 0) = 100000Hz (slot req 100000Hz, actual 100000HZ div = 0)
[    2.428918] vendor storage:20160801 ret = 0
[    2.574823] usb 3-1: new full-speed USB device number 2 using ohci-platform
[    2.752225] usb 1-1: New USB device found, idVendor=0bda, idProduct=8179
[    2.752230] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    2.752234] usb 1-1: Product: 802.11n WLAN NIC
[    2.752238] usb 1-1: Manufacturer: Realtek
[    2.753386] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/standby-led[0]' - status (-517)
[    2.768560] usb 3-1: New USB device found, idVendor=046d, idProduct=c52b
[    2.768565] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.768570] usb 3-1: Product: USB Receiver
[    2.768574] usb 3-1: Manufacturer: Logitech
[    2.777468] input: Logitech USB Receiver as /devices/platform/ff5d0000.usb/usb3/3-1/3-1:1.0/0003:046D:C52B.0001/input/input4
[    2.804653] Freeing unused kernel memory: 2880K
[    2.828849] hid-generic 0003:046D:C52B.0001: input,hidraw0: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-ff5d0000.usb-1/input0
[    2.835151] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/standby-led[0]' - status (-517)
[    2.840298] input: Logitech USB Receiver as /devices/platform/ff5d0000.usb/usb3/3-1/3-1:1.1/0003:046D:C52B.0002/input/input5
[    2.891960] hid-generic 0003:046D:C52B.0002: input,hiddev0,hidraw1: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-ff5d0000.usb-1/input1
[    2.892292] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/standby-led[0]' - status (-517)
[    2.899871] hid-generic 0003:046D:C52B.0003: hiddev0,hidraw2: USB HID v1.11 Device [Logitech USB Receiver] on usb-ff5d0000.usb-1/input2
[    2.900175] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/standby-led[0]' - status (-517)
[    4.453861] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
[    4.455008] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities
[    4.646766] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    9.189279] random: nonblocking pool is initialized
[   18.635639] systemd[1]: System time before build time, advancing clock.
[   18.644764] systemd[1]: systemd 232 running in system mode. (-PAM -AUDIT -SELINUX -IMA -APPARMOR -SMACK -SYSVINIT -UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS -ACL -XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN)
[   18.645248] systemd[1]: Detected architecture arm64.
[   18.646758] systemd[1]: Set hostname to <Lakka>.
[   18.705903] systemd[1]: Listening on Journal Socket.
[   18.706520] systemd[1]: Listening on udev Kernel Socket.
[   18.707971] systemd[1]: Created slice System Slice.
[   18.710340] systemd[1]: Mounting Debug File System...
[   18.712798] systemd[1]: Starting Samba Configuration...
[   18.714033] systemd[1]: Created slice User and Session Slice.
[   18.715423] systemd[1]: Listening on udev Control Socket.
[   18.718881] systemd[1]: Starting Debug Shell on /dev/ttyFIQ0...
[   18.722111] systemd[1]: Mounting POSIX Message Queue File System...
[   18.722981] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[   18.723760] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[   18.724474] systemd[1]: Listening on Journal Socket (/dev/log).
[   18.747005] systemd[1]: Starting Load Kernel Modules...
[   18.749723] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[   18.752621] systemd[1]: Starting Setup machine-id...
[   18.753062] systemd[1]: Reached target Slices.
[   18.753491] systemd[1]: Reached target Swap.
[   18.756536] systemd[1]: Mounting Temporary Directory...
[   18.764083] systemd[1]: Starting Remount Root and Kernel File Systems...
[   18.765114] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[   18.767551] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 414; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '-v2.1-rc3-1261-g870ffe9', rk_ko_ver is '5', built at '10:24:13', on 'Sep 29 2017'.
[   18.767782] mali-utgard ff300000.gpu: mali_platform_device->num_resources = 9
[   18.767797] mali-utgard ff300000.gpu: resource[0].start = 0x0x00000000ff300000
[   18.767804] mali-utgard ff300000.gpu: resource[1].start = 0x0x00000000ff300000
[   18.767811] mali-utgard ff300000.gpu: resource[2].start = 0x0x0000000000000011
[   18.767819] mali-utgard ff300000.gpu: resource[3].start = 0x0x0000000000000012
[   18.767826] mali-utgard ff300000.gpu: resource[4].start = 0x0x0000000000000013
[   18.767833] mali-utgard ff300000.gpu: resource[5].start = 0x0x0000000000000014
[   18.767840] mali-utgard ff300000.gpu: resource[6].start = 0x0x0000000000000015
[   18.767847] mali-utgard ff300000.gpu: resource[7].start = 0x0x0000000000000016
[   18.767854] mali-utgard ff300000.gpu: resource[8].start = 0x0x0000000000000017
[   18.767862] D : [File] : drivers/gpu/arm/mali400/mali/platform/rk/rk.c; [Line] : 518; [Func] : mali_platform_device_init(); to add platform_specific_data to platform_device_of_mali.
[   18.767893] mali-utgard ff300000.gpu: Looking up mali-supply from device tree
[   18.768745] devfreq ff300000.gpu: Couldn't update frequency transition information.
[   18.769374] systemd[1]: Mounting Variable Directory...
[   18.769857] systemd[1]: Reached target Paths.
[   18.770862] systemd[1]: Listening on RPCbind Server Activation Socket.
[   18.771581] systemd[1]: Reached target RPC Port Mapper.
[   18.772106] Mali: Mali device driver loaded
[   18.772919] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/standby-led[0]' - status (-517)
[   18.781911] systemd[1]: Mounted Debug File System.
[   18.782500] systemd[1]: Mounted POSIX Message Queue File System.
[   18.783049] systemd[1]: Mounted Variable Directory.
[   18.783571] systemd[1]: Mounted Temporary Directory.
[   18.786197] systemd[1]: Started Samba Configuration.
[   18.788981] systemd[1]: Started Debug Shell on /dev/ttyFIQ0.
[   18.791268] systemd[1]: Started Load Kernel Modules.
[   18.793022] systemd[1]: Started Create list of required static device nodes for the current kernel.
[   18.794731] systemd[1]: Started Setup machine-id.
[   18.796834] systemd[1]: Started Remount Root and Kernel File Systems.
[   18.833100] systemd[1]: Starting udev Coldplug all Devices...
[   18.835884] systemd[1]: Starting Journal Service...
[   18.839698] systemd[1]: Starting Create Static Device Nodes in /dev...
[   18.842724] systemd[1]: Mounting Configuration File System...
[   18.846301] systemd[1]: Starting Apply Kernel Variables...
[   18.849364] systemd[1]: Starting Setup Timezone data...
[   18.860910] systemd[1]: Mounted Configuration File System.
[   18.869431] systemd[1]: Started Create Static Device Nodes in /dev.
[   18.877415] systemd[1]: Reached target Local File Systems (Pre).
[   18.880993] systemd[1]: Reached target Local File Systems.
[   18.885783] systemd[1]: Started Setup Timezone data.
[   18.895175] systemd[1]: Started Apply Kernel Variables.
[   19.001995] systemd[1]: Started Journal Service.
[   19.025756] systemd-journald[259]: Received request to flush runtime journal from PID 1
[   20.229670] rk_gmac-dwmac ff540000.ethernet: rk_get_eth_addr: mac address: 3e:49:bb:ba:56:31
[   20.229687] eth0: device MAC address 3e:49:bb:ba:56:31
[   20.232273] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/standby-led[0]' - status (-517)
[  289.589252] drm_crtc_check_viewport: skip check
[  307.298762] drm_crtc_check_viewport: skip check
[ 1125.902163] rk_gmac-dwmac ff540000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx


The above dmesg log is from my first bootup of the Lakka test image :

Linux Lakka 4.4.83 #1 SMP Fri Sep 29 10:33:18 CDT 2017 aarch64 GUN/Linux

git version  28397b3

Rock64.arm-8.1.2

marcushh_Pb



retroarch does start;  there are a couple of fonts missing, but most gnu+linux stuff works from busybox;  python2.7 runs fine, nano and vim work (filesystem is ok), I am able to play around in the retroarch menu, see system information, exit and reboot;  no problems.

There are no roms apparently;  have not tried to play any games , nor have I tested my game pads yet.  I left you some more detailed messages on  irc  ( use !msg get ) .

I'll be around my lab on Saturday should you have questions, catch me on IRC.

marcushh_Pb

Shy


notes:

   Icons do not appear on the retroarch console menu;  I tried to load content;  and it did download;  but I must be doing something wrong, because can't seem to do anything with it;  I can navigate the console menu however;  

The wifi settings fail to see my wifi dongle ;  scan doesn't see local networks;

marcushh_Pb
Shy
marcushh777    Cool

please join us for a chat @  irc.pine64.xyz:6667   or ssl  irc.pine64.xyz:6697

( I regret that I am not able to respond to personal messages;  let's meet on irc! )
  Reply
#2
My internet is broken, so can't complete the image download - once I have it sorted out I'll test the image.
Marcus, as for ROMs - no distribution can include ROMs, thats why they are not there Smile
You can find me on IRC, Discord and Twitter


  Reply
#3
I'm interested in trying it also, but can not find anywhere to download it. I understand it is BETA, but I'd like to help test it and report bugs.
  Reply
#4
(10-03-2017, 10:24 AM)dudemo Wrote: I'm interested in trying it also, but can not find anywhere to download it. I understand it is BETA, but I'd like to help test it and report bugs.

It hasn't been made public, but given that as much feedback as possible is a good thing at an early stage I think its ok to share it on here. Do keep in mind its pre-release. 

You can download the image here to test out and provide feedback. 
You can find me on IRC, Discord and Twitter


  Reply
#5
Awesome, Luke. Thanks! I'll definitely keep in mind that this is prerelease and treat it as such.
  Reply
#6
Finally got around to trying it out ... sadly, it doesn't load retroarch assets. Also, it doesn't auto-start - i need to launch retroarch manually.
You can find me on IRC, Discord and Twitter


  Reply
#7
RetroArch will probably autostart if you remove textmode (or replace it with quiet) in extlinux/extlinux.conf on the boot partition
  Reply
#8
(10-10-2017, 02:43 PM)Kwiboo Wrote: RetroArch will probably autostart if you remove textmode (or replace it with quiet) in extlinux/extlinux.conf on the boot partition

Yes. Still its weird that the assets don't load ... I experienced this in the past putting together a dedicated Retroarch build for the Pine64 - I remember that it was a permissions issue. Didn't have time to look into this - but I think the nature of the issue is different as the Lakka build runs as root.
You can find me on IRC, Discord and Twitter


  Reply
#9
(10-10-2017, 07:02 AM)Luke Wrote: Finally got around to trying it out ... sadly, it doesn't load retroarch assets. Also, it doesn't auto-start - i need to launch retroarch manually.

hi lukasz;  same two issues.
marcushh777    Cool

please join us for a chat @  irc.pine64.xyz:6667   or ssl  irc.pine64.xyz:6697

( I regret that I am not able to respond to personal messages;  let's meet on irc! )
  Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  arch rock64 does not boot nemnob 1 868 09-20-2024, 11:18 AM
Last Post: AwU2HBg
  DietPi OS for ROCK64 MichaIng 42 41,601 09-01-2024, 06:43 AM
Last Post: RaymondDay
Smile First Lakka image for Rock64! Luke 47 79,477 09-01-2024, 06:05 AM
Last Post: RaymondDay
  problem with debian emmc boot G4zCDzWb 9 1,047 07-30-2024, 05:41 AM
Last Post: Boia11
  irradium (based on crux linux) Rock64 riscv64, aarch64 mara 4 763 07-20-2024, 10:32 PM
Last Post: mara
  Rock64 v2 - did not work song / audio sqw200zu 2 1,769 03-14-2024, 03:09 AM
Last Post: dmitrymyadzelets
  Rock64 won't boot dstallmo 0 574 12-27-2023, 10:34 AM
Last Post: dstallmo
  HDMI doesn't work on rock64 Noung1991 1 991 11-21-2023, 08:33 AM
Last Post: as365n4
  Rock64 + Klipper + KlipperScreen Instructions godzilla62 0 983 10-22-2023, 01:52 AM
Last Post: godzilla62
  Rock64 Debian 11 (Bullseye) install problem jbize 15 10,617 10-12-2023, 05:14 PM
Last Post: tpaul

Forum Jump:


Users browsing this thread: 1 Guest(s)