kreyren@dreamon ~$ sudo picocom -b 1500000 /dev/ttyUSB0 Password: picocom v3.1 port is : /dev/ttyUSB0 flowcontrol : none baudrate is : 1500000 parity is : none databits are : 8 stopbits are : 1 escape is : C-a local echo is : no noinit is : no noreset is : no hangup is : no nolock is : no send_cmd is : sz -vv receive_cmd is : rz -vv -E imap is : omap is : emap is : crcrlf,delbs, logfile is : none initstring : none exit_after is : not set exit is : no Type [C-a] [C-h] to see available commands Terminal ready DDR Version 1.24 20191016 In channel 0 CS = 0 MR0=0x98 MR4=0x1 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 1 CS = 0 MR0=0x98 MR4=0x1 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 0 training pass! channel 1 training pass! change freq to 416MHz 0,1 Channel 0: LPDDR4,416MHz Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB Channel 1: LPDDR4,416MHz Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB 256B stride channel 0 CS = 0 MR0=0x98 MR4=0x1 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 1 CS = 0 MR0=0x98 MR4=0x1 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 0 training pass! channel 1 training pass! channel 0, cs 0, advanced training done channel 1, cs 0, advanced training done change freq to 856MHz 1,0 ch 0 ddrconfig = 0x101, ddrsize = 0x20 ch 1 ddrconfig = 0x101, ddrsize = 0x20 pmugrf_os_reg[2] = 0x3281F281, stride = 0x9 ddr_set_rate to 328MHZ ddr_set_rate to 666MHZ ddr_set_rate to 416MHZ, ctl_index 0 ddr_set_rate to 856MHZ, ctl_index 1 support 416 856 328 666 MHz, current 856MHz OUT Boot1 Release Time: Dec 24 2019 18:00:26, version: 1.24 CPUId = 0x0 ChipType = 0x10, 338 mmc: ERROR: SDHCI ERR:cmd:0x102,stat:0x18000 mmc: ERROR: Card did not respond to voltage select! emmc reinit mmc: ERROR: SDHCI ERR:cmd:0x102,stat:0x18000 mmc: ERROR: Card did not respond to voltage select! emmc reinit mmc: ERROR: SDHCI ERR:cmd:0x102,stat:0x18000 mmc: ERROR: Card did not respond to voltage select! SdmmcInit=2 1 mmc0:cmd5,20 SdmmcInit=0 0 BootCapSize=0 UserCapSize=3781MB FwPartOffset=2000 , 0 StorageInit ok = 66526 SecureMode = 0 SecureInit read PBA: 0x4 SecureInit read PBA: 0x404 SecureInit read PBA: 0x804 SecureInit read PBA: 0xc04 SecureInit read PBA: 0x1004 SecureInit read PBA: 0x1404 SecureInit read PBA: 0x1804 SecureInit read PBA: 0x1c04 SecureInit ret = 0, SecureMode = 0 atags_set_bootdev: ret:(0) GPT 0x3380ea0 signature is wrong recovery gpt... GPT 0x3380ea0 signature is wrong recovery gpt fail! LoadTrust Addr:0x4000 No find bl30.bin No find bl32.bin Load uboot, ReadLba = 2000 Load OK, addr=0x200000, size=0xa44f8 RunBL31 0x40000 @ 177286 us NOTICE: BL31: v1.3(debug):734d84297 NOTICE: BL31: Built : 15:30:40, Dec 12 2019 NOTICE: BL31: Rockchip release version: v1.1 INFO: GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3 INFO: Using opteed sec cpu_context! INFO: boot cpu mask: 0 INFO: plat_rockchip_pmu_init(1190): pd status 3e INFO: BL31: Initializing runtime services WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK ERROR: Error initializing runtime service opteed_fast INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x200000 INFO: SPSR = 0x3c9 U-Boot 2017.09 (Mar 05 2022 - 14:01:11 +0100), Build: jenkins-RK3399-919 Model: Rockchip RK3399 Evaluation Board DRAM: 2 GiB Relocation Offset is: 7fd1a000 PMIC: RK808 pwm-regulator(vdd-center): init 950000 uV vdd_center 950000 uV regulator(vdd-center) init 950000 uV MMC: dwmmc@fe320000: 1, sdhci@fe330000: 0 Using default environment In: serial@ff1a0000 Out: serial@ff1a0000 Err: serial@ff1a0000 Model: Rockchip RK3399 Evaluation Board Net: eth0: ethernet@fe300000 Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found /extlinux/extlinux.conf Retrieving file: /extlinux/extlinux.conf reading /extlinux/extlinux.conf 228 bytes read in 5 ms (43.9 KiB/s) 1: LibreELEC Retrieving file: /KERNEL reading /KERNEL 24158216 bytes read in 2010 ms (11.5 MiB/s) append: boot=UUID=0503-4902 disk=UUID=8ff85d86-0886-4367-affc-e7e92877481a quiet console=uart8250,mmio32,0xff1a0000 console=tty0 coherent_pool=2M cec.debounce_ms=5000 Retrieving file: /rk3399-rockpro64.dtb reading /rk3399-rockpro64.dtb 76456 bytes read in 12 ms (6.1 MiB/s) ## Flattened Device Tree blob at 01f00000 Booting using the fdt blob at 0x1f00000 Loading Device Tree to 000000007deeb000, end 000000007df00aa7 ... OK Adding bank: start=0x00200000, size=0x7fe00000 Starting kernel ... [ 0.501628] reg-fixed-voltage vcc1v8-s3: Failed to register regulator: -517 [ 0.502032] reg-fixed-voltage vcc3v0-sd: Failed to register regulator: -517 [ 0.503788] reg-fixed-voltage vcc3v3-sys: Failed to register regulator: -517 [ 0.504216] reg-fixed-voltage vcc5v0-host-regulator: Failed to register regulator: -517 [ 0.504476] reg-fixed-voltage vcc5v0-typec-regulator: Failed to register regulator: -517 [ 0.728216] rockchip-usb2phy ff770000.syscon:usb2-phy@e450: failed to create phy [ 0.730942] rockchip-usb2phy ff770000.syscon:usb2-phy@e460: failed to create phy [ 0.775414] panfrost ff9a0000.gpu: [drm:panfrost_devfreq_init] *ERROR* Couldn't set OPP regulators [ 0.797848] rk_gmac-dwmac fe300000.ethernet: phy regulator is not available yet, deferred probing [ 0.877006] rk808 0-001b: failed to register 12 regulator [ 0.940877] rockchip-saradc ff100000.saradc: failed to get regulator, -517 [ 1.016601] reg-fixed-voltage vcc1v8-s3: Failed to register regulator: -517 [ 1.018157] reg-fixed-voltage vcc3v0-sd: Failed to register regulator: -517 [ 1.043032] rk_gmac-dwmac fe300000.ethernet: phy regulator is not available yet, deferred probing [ 1.257448] rockchip-saradc ff100000.saradc: failed to get regulator, -517 [ 1.332664] rk_gmac-dwmac fe300000.ethernet: cannot get clock clk_mac_speed [ 1.435022] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! [ 1.435748] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! [ 1.436456] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! [ 1.437221] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! [ 1.437929] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! [ 1.438635] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! [ 1.439339] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! [ 1.440064] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! [ 1.440771] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! [ 1.441475] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! [ 1.442178] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! [ 1.442882] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! [ 1.443602] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! [ 1.444307] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! [ 1.445012] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! [ 1.445717] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! [ 1.446421] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! [ 1.447303] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! [ 1.448033] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! [ 35.612440] Disabling IRQ #78