HELLO! BOOT0 is starting! boot0 commit : 045061a8bb2580cb3fa02e301f52a015040c158f boot0 version : 4.0.0 set pll start set pll end rtc[0] value = 0x00000000 rtc[1] value = 0x00000000 rtc[2] value = 0x00000000 rtc[3] value = 0x00000000 rtc[4] value = 0x00000000 rtc[5] value = 0x00000000 DRAM driver version: V1.1 rsb_send_initseq: rsb clk 400Khz -> 3Mhz PMU: AXP81X ddr voltage = 1500 mv DRAM Type = 3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3) DRAM clk = 672 MHz DRAM zq value: 003b3bbb DRAM single rank full DQ OK DRAM size = 1024 MB DRAM init ok dram size =1024 card boot number = 0, boot0 copy = 0 card no is 0 sdcard 0 line count 4 [mmc]: mmc driver ver 2015-05-08 20:06 [mmc]: sdc0 spd mode error, 2 [mmc]: Wrong media type 0x00000000 [mmc]: ***Try SD card 0*** [mmc]: HSSDR52/SDR25 4 bit [mmc]: 50000000 Hz [mmc]: 30528 MB [mmc]: ***SD/MMC 0 init OK!!!*** sdcard 0 init ok The size of uboot is 000ec000. sum=e99e0b56 src_sum=e99e0b56 Succeed in loading uboot from sdmmc flash. boot0: start load other image boot0: Loading BL3-1 Loading file 0 at address 0x40000000,size 0x00008400 success boot0: Loading scp Loading file 2 at address 0x00040000,size 0x00019c00 success set arisc reset to de-assert state Ready to disable icache. Jump to secend Boot. U-Boot 2014.07-4-pine64-longsleep (Apr 17 2016 - 20:46:05) Allwinner Technology uboot commit : b95bd2301e5765a3866a3447327ecf53deb0270b rsb: secure monitor exist [ 0.336]pmbus: ready [ 0.338][ARISC] :arisc initialize [ 0.669][ARISC] :arisc_dvfs_cfg_vf_table: support only one vf_table [ 0.784][ARISC] :sunxi-arisc driver startup succeeded [ 0.817]PMU: AXP81X [ 0.819]PMU: AXP81X found bat_vol=0, ratio=100 [ 0.826]PMU: dcdc2 1100 [ 0.829]PMU: cpux 1008 Mhz,AXI=336 Mhz PLL6=600 Mhz,AHB1=200 Mhz, APB1=100Mhz AHB2=300Mhz MBus=400Mhz device_type = 3253, onoff=1 dcdc1_vol = 3300, onoff=1 dcdc2_vol = 1100, onoff=1 dcdc6_vol = 1100, onoff=1 aldo1_vol = 2800, onoff=0 aldo2_vol = 1800, onoff=1 aldo3_vol = 3000, onoff=1 dldo1_vol = 3300, onoff=0 dldo2_vol = 3300, onoff=0 dldo3_vol = 2800, onoff=0 dldo4_vol = 3300, onoff=1 eldo1_vol = 1800, onoff=1 eldo2_vol = 1800, onoff=0 eldo3_vol = 1800, onoff=0 fldo1_vol = 1200, onoff=0 fldo2_vol = 1100, onoff=1 gpio0_vol = 3100, onoff=0 vbus not exist no battery, limit to dc run key detect no key found no uart input DRAM: 1008 MiB fdt addr: 0x76ebc080 Relocation Offset is: 35f0e000 In: serial Out: serial Err: serial gic: sec monitor mode [ 1.136]start drv_disp_init init_clocks: finish init_clocks. enable power vcc-hdmi-33, ret=0 drv_disp_init finish boot_disp.output_disp=0 boot_disp.output_type=3 boot_disp.output_type=10 fetch script data boot_disp.auto_hpd fail disp0 device type(4) enable attched ok, mgr0<-->device1, type=4, mode=10 [ 1.485]end workmode = 0,storage type = 1 [ 1.489]MMC: 0 [mmc]: mmc driver ver 2015-06-03 13:50:00 SUNXI SD/MMC: 0 [mmc]: start mmc_calibrate_delay_unit, don't access device... [mmc]: delay chain cal done, sample: 192(ps) [mmc]: media type 0x0 [mmc]: Wrong media type 0x0 [mmc]: ************Try SD card 0************ [mmc]: host caps: 0x27 [mmc]: MID 1b PSN 824c5d4d [mmc]: PNM 00000 -- 0x30-30-30-30-30 [mmc]: PRV 1.0 [mmc]: MDT m-11 y-2015 [mmc]: speed mode : HSSDR52/SDR25 [mmc]: clock : 50000000 Hz [mmc]: bus_width : 4 bit [mmc]: user capacity : 30528 MB [mmc]: ************SD/MMC 0 init OK!!!************ [mmc]: erase_grp_size : 0x1WrBlk*0x200=0x200 Byte [mmc]: secure_feature : 0x0 [mmc]: secure_removal_type : 0x0 [ 1.674]sunxi flash init ok [mmc]: Has init [ 1.706]---drivers/mmc/mmc.c 2733 mmc_init reading uboot.env ** Unable to read "uboot.env" from mmc0:1 ** Using default environment --------fastboot partitions-------- mbr not exist base bootcmd=run mmcbootcmd bootcmd set setargs_mmc key 0 recovery key high 12, low 10 fastboot key high 6, low 4 no misc partition is found to be run cmd=run mmcbootcmd update dtb dram start update dtb dram end serial is: 8400519008005c19014b get Pine64 model from DRAM size DRAM >512M Pine64 model: pine64-plus no battery exist sunxi_bmp_logo_display ** Bad device size - sunxi_flash 0 ** sunxi bmp info error : unable to open logo file bootlogo.bmp [ 1.911]inter uboot shell Hit any key to stop autoboot: 0 [mmc]: Has init [ 5.021]---drivers/mmc/mmc.c 2733 mmc_init reading uEnv.txt [mmc]: blkcnt should not be 0 137 bytes read in 5 ms (26.4 KiB/s) Loading boot environment ... [mmc]: Has init [ 5.041]---drivers/mmc/mmc.c 2733 mmc_init reading boot.scr ** Unable to read file boot.scr ** Booting with defaults ... [mmc]: Has init [ 5.059]---drivers/mmc/mmc.c 2733 mmc_init reading pine64/sun50i-a64-pine64-plus.dtb 69134 bytes read in 9 ms (7.3 MiB/s) [mmc]: Has init [ 5.113]---drivers/mmc/mmc.c 2733 mmc_init reading pine64/Image 11170152 bytes read in 562 ms (19 MiB/s) [mmc]: Has init [ 5.686]---drivers/mmc/mmc.c 2733 mmc_init reading initrd.img 1076058 bytes read in 56 ms (18.3 MiB/s) Image lacks image_size field, assuming 16MiB ## Flattened Device Tree blob at 45000000 Booting using the fdt blob at 0x45000000 reserving fdt memory region: addr=41010000 size=10000 reserving fdt memory region: addr=41020000 size=800 reserving fdt memory region: addr=40100000 size=4000 reserving fdt memory region: addr=40104000 size=1000 reserving fdt memory region: addr=40105000 size=1000 reserving fdt memory region: addr=45000000 size=11000 Loading Ramdisk to 76dad000, end 76eb3b5a ... OK Loading Device Tree to 44feb000, end 44ffefff ... OK Starting kernel ... [mmc]: MMC Device 2 not found [mmc]: mmc 2 not find, so not exit [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.10.65-7-pine64-longsleep (longsleep@mose2) (gcc version 5.3.1 20160413 (Ubuntu/Linaro 5.3.1-14ubuntu2) ) #28 SMP PREEMPT Sat Apr 23 20:13:25 CEST 2016 [ 0.000000] CPU: AArch64 Processor [410fd034] revision 4 [ 0.000000] Machine: sun50iw1p1 [ 0.000000] cma: CMA: reserved 64 MiB at 7c000000 [ 0.000000] script_init enter! [ 0.000000] script buffer is NULL! [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] PERCPU: Embedded 12 pages/cpu @ffffffc03af98000 s19712 r8192 d21248 u49152 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 254520 [ 0.000000] Kernel command line: console=tty0 console=ttyS0,115200n8 no_console_suspend earlycon=uart,mmio32,0x01c28000 mac_addr=7a:6e:63:ac:21:f1 root=/dev/mmcblk0p2 ro rootwait [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) [ 0.000000] Memory: 1008MB = 1008MB total [ 0.000000] Memory: 937300k/937300k available, 94892k reserved [ 0.000000] Virtual kernel memory layout: [ 0.000000] vmalloc : 0xffffff8000000000 - 0xffffffbbffff0000 (245759 MB) [ 0.000000] vmemmap : 0xffffffbc00e38000 - 0xffffffbc01c00000 ( 13 MB) [ 0.000000] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc03f000000 ( 1008 MB) [ 0.000000] .init : 0xffffffc000957000 - 0xffffffc0009d0d00 ( 488 kB) [ 0.000000] .text : 0xffffffc000080000 - 0xffffffc0009569b4 ( 9051 kB) [ 0.000000] .data : 0xffffffc0009d1000 - 0xffffffc000b27168 ( 1369 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] allocated 4194304 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 6.362806] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 6.362837] pid_max: default: 32768 minimum: 301 [ 6.362939] Security Framework initialized [ 6.362973] AppArmor: AppArmor initialized [ 6.363017] Mount-cache hash table entries: 256 [ 6.373415] Initializing cgroup subsys memory [ 6.373476] Initializing cgroup subsys devices [ 6.373494] Initializing cgroup subsys freezer [ 6.373509] Initializing cgroup subsys blkio [ 6.373524] Initializing cgroup subsys perf_event [ 6.373546] Initializing cgroup subsys hugetlb [ 6.373598] ftrace: allocating 25847 entries in 101 pages [ 6.403781] CPU0: update cpu_power 1968128 [ 6.403815] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available [ 6.404741] virtual base = 0xffffff800000a000. [ 6.404760] gicd_base = 0xffffff800000c000. [ 6.404773] gicc_base = 0xffffff800000e000. [ 6.405349] CPU1: Booted secondary processor [ 6.405372] CPU1: update cpu_power 1968128 [ 6.407974] CPU2: Booted secondary processor [ 6.407985] CPU2: update cpu_power 1968128 [ 6.412093] CPU3: Booted secondary processor [ 6.412104] CPU3: update cpu_power 1968128 [ 6.412183] Brought up 4 CPUs [ 6.412257] SMP: Total of 4 processors activated (192.00 BogoMIPS). [ 6.412791] devtmpfs: initialized [ 6.417591] atomic64 test passed [ 6.417612] pinctrl core: initialized pinctrl subsystem [ 6.420584] NET: Registered protocol family 16 [ 6.420894] script_sysfs_init success [ 6.421735] dump_class_init,806, success [ 6.422374] vdso: 2 pages (1 code, 1 data) at base ffffffc0009d9000 [ 6.422406] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 6.423712] software IO TLB [mem 0x79c00000-0x7a000000] (4MB) mapped at [ffffffc038c00000-ffffffc038ffffff] [ 6.424654] DMA: preallocated 256 KiB pool for atomic allocations [ 6.424837] Serial: AMBA PL011 UART driver [ 6.425203] axp81x_board_init: axp regl_devs num = 23 [ 6.425418] pll_audio-set_default_rate=24576000 success! [ 6.425449] pll_video0-set_default_rate=297000000 success! [ 6.425533] pll_video1-set_default_rate=297000000 success! [ 6.425601] pll_de-set_default_rate=297000000 success! [ 6.426333] de-set_default_source=pll_de success! [ 6.426350] de-set_default_rate=297000000 success! [ 6.426403] tcon0-set_default_source=pll_mipi success! [ 6.426446] tcon1-set_default_source=pll_video0 success! [ 6.426676] hdmi-set_default_source=pll_video0 success! [ 6.429211] sun50i-r-pinctrl 1f02c00.pinctrl: initialized sunXi PIO driver [ 6.429461] [sun50iw1p1_pinctrl_probe][838] [ 6.431212] sun50i-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver [ 6.432504] sunxi hwspinlock vbase:0xffffff800005c000 [ 6.442406] sunxi_chipid_probe,150: soc bin:0 [ 6.459561] bio: create slab at 0 [ 6.459984] pwm module init! [ 6.462290] SCSI subsystem initialized [ 6.462787] usbcore: registered new interface driver usbfs [ 6.462904] usbcore: registered new interface driver hub [ 6.463040] usbcore: registered new device driver usb [ 6.464325] Linux video capture interface: v2.00 [ 6.465295] [ARISC] :sunxi-arisc driver v1.10 [ 6.477072] [ARISC] :sunxi-arisc driver v1.10 startup succeeded [ 6.477472] Advanced Linux Sound Architecture Driver Initialized. [ 6.478046] NetLabel: Initializing [ 6.478060] NetLabel: domain hash size = 128 [ 6.478072] NetLabel: protocols = UNLABELED CIPSOv4 [ 6.478118] NetLabel: unlabeled traffic allowed by default [ 6.478367] [pm]aw_pm_init! [ 6.478450] rtc physical base = 0x0000000001f00000 . [ 6.478496] np name = /soc@01c00000/rtc@01f00000. [ 6.478511] base = ffffff8000070100, len = 4. [ 6.478525] pmu name: pmu0 . [ 6.478569] pmu0_enable = 0x1. [ 6.478582] pmux_id = 0x6. [ 6.478594] pmux_twi_id = 0x1. [ 6.478606] pmux_twi_addr = 0x34. [ 6.478617] pmu name: pmu1 . [ 6.478674] Warning: can not find np for pmu1. [ 6.478910] add_sys_pwr_dm: get ldo name for id: vcc-lpddr failed [ 6.479076] after inited: sys_mask config = 0x4a55. [ 6.479110] Warning: can not find np for dynamic_standby_para. [ 6.479235] [pm]valid [ 6.479245] [pm]valid [ 6.479255] Notice: sun9i&sun8iw5&sun50i not need support normal standby, change to super standby. [ 6.479454] Switching to clocksource arch_sys_counter [ 6.490002] AppArmor: AppArmor Filesystem Enabled [ 6.502392] NET: Registered protocol family 2 [ 6.503036] TCP established hash table entries: 8192 (order: 5, 131072 bytes) [ 6.503180] TCP bind hash table entries: 8192 (order: 5, 131072 bytes) [ 6.503331] TCP: Hash tables configured (established 8192 bind 8192) [ 6.503413] TCP: reno registered [ 6.503430] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 6.503470] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 6.503691] NET: Registered protocol family 1 [ 6.503956] RPC: Registered named UNIX socket transport module. [ 6.503974] RPC: Registered udp transport module. [ 6.503987] RPC: Registered tcp transport module. [ 6.504001] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 6.504160] Unpacking initramfs... [ 6.547787] Freeing initrd memory: 1048K (ffffffc035dad000 - ffffffc035eb3000) [ 6.548508] kvm [1]: Using HYP init bounce page @7aaf8000 [ 6.548974] kvm [1]: interrupt-controller@1c84000 IRQ25 [ 6.549323] kvm [1]: timer IRQ27 [ 6.549342] kvm [1]: Hyp mode initialized successfully [ 6.550704] lock super standby defaultly! [ 6.550728] lookup_scene_lock_name: new scene lock super_standby [ 6.550744] scene_lock_init name=super_standby [ 6.550759] scene_lock: super_standby, type 5, count 1 [ 6.551423] audit: initializing netlink socket (disabled) [ 6.551482] type=2000 audit(0.170:1): initialized [ 6.552371] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 6.552825] VFS: Disk quotas dquot_6.5.2 [ 6.552949] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 6.553371] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 6.553769] NFS: Registering the id_resolver key type [ 6.553816] Key type id_resolver registered [ 6.553830] Key type id_legacy registered [ 6.553850] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 6.554006] NTFS driver 2.1.30 [Flags: R/W]. [ 6.554271] fuse init (API version 7.22) [ 6.554668] msgmni has been set to 1960 [ 6.555459] io scheduler noop registered [ 6.555476] io scheduler deadline registered [ 6.555520] io scheduler cfq registered (default) [ 6.556327] [DISP]disp_module_init [ 6.556880] [DISP] boot_disp:0x40a [ 6.557456] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail [ 6.557617] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail [ 6.557774] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail [ 6.558901] [DISP] fb_base:0x47400000 [ 6.566476] [DISP] Fb_map_kernel_logo,line:885:this is not a bmp picture. [ 6.596354] Console: switching to colour frame buffer device 240x67 [ 6.625319] [DISP]disp_module_init finish [ 6.625847] uart0: ttyS0 at MMIO 0x1c28000 (irq = 32) is a SUNXI [ 6.626002] sw_console_setup()1173 - console setup baud 115200 parity n bits 8, flow n [ 7.585607] console [ttyS0] enabled [ 7.590048] uart1: ttyS1 at MMIO 0x1c28400 (irq = 33) is a SUNXI [ 7.597084] uart2: ttyS2 at MMIO 0x1c28800 (irq = 34) is a SUNXI [ 7.604189] uart3: ttyS3 at MMIO 0x1c28c00 (irq = 35) is a SUNXI [ 7.611264] uart4: ttyS4 at MMIO 0x1c29000 (irq = 36) is a SUNXI [ 7.618467] misc dump reg init [ 7.622218] [drm] Initialized drm 1.1.0 20060810 [ 7.630897] loop: module loaded [ 7.634666] sunxi-bt bt.27: Missing bt_power. [ 7.639525] sunxi-bt bt.27: bt_power_name ((null)) [ 7.644886] sunxi-bt bt.27: io_regulator_name (vcc-wifi-io) [ 7.651136] sunxi-bt bt.27: bt_rst gpio=356 mul-sel=1 pull=-1 drv_level=-1 data=0 [ 7.659898] sunxi-bt bt.27: clk not config [ 7.664604] sunxi-bt bt.27: block state already is 1 [ 7.670544] sunxi-wlan wlan.26: wlan_busnum (1) [ 7.675594] sunxi-wlan wlan.26: Missing wlan_power. [ 7.681039] sunxi-wlan wlan.26: wlan_power_name ((null)) [ 7.686960] sunxi-wlan wlan.26: io_regulator_name (vcc-wifi-io) [ 7.693589] sunxi-wlan wlan.26: wlan_regon gpio=354 mul-sel=1 pull=-1 drv_level=-1 data=0 [ 7.703128] sunxi-wlan wlan.26: wlan_hostwake gpio=355 mul-sel=6 pull=-1 drv_level=-1 data=0 [ 7.712946] sunxi-wlan wlan.26: clk not config [ 7.718543] tun: Universal TUN/TAP device driver, 1.6 [ 7.724184] tun: (C) 1999-2004 Max Krasnyansky [ 7.731787] WARNING: Get ephy clock is failed [ 7.737264] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 7.744707] get ehci0-controller drv_vbus_gpio is fail [ 7.750445] get ehci0-controller, regulator_io is no nocare [ 7.756704] [sunxi-ehci0]: probe, pdev->name: 1c1a000.ehci0-controller, sunxi_ehci: 0xffffffc000bd16a8, 0x:ffffff80000ae000, irq_no:68 [ 7.770234] sunxi-ehci 1c1a000.ehci0-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 7.780345] sunxi-ehci 1c1a000.ehci0-controller: new USB bus registered, assigned bus number 1 [ 7.790238] sunxi-ehci 1c1a000.ehci0-controller: irq 104, io mem 0xffffffc0004bf654 [ 7.817758] sunxi-ehci 1c1a000.ehci0-controller: USB 0.0 started, EHCI 1.00 [ 7.826093] hub 1-0:1.0: USB hub found [ 7.830292] hub 1-0:1.0: 1 port detected [ 7.840792] scene_lock_init name=ehci_standby [ 7.851653] get ehci1-controller drv_vbus_gpio is fail [ 7.863261] get ehci1-controller, regulator_io is no nocare [ 7.875337] [sunxi-ehci1]: probe, pdev->name: 1c1b000.ehci1-controller, sunxi_ehci: 0xffffffc000bd18f8, 0x:ffffff80000b6000, irq_no:6a [ 7.894812] sunxi-ehci 1c1b000.ehci1-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 7.911015] sunxi-ehci 1c1b000.ehci1-controller: new USB bus registered, assigned bus number 2 [ 7.927051] sunxi-ehci 1c1b000.ehci1-controller: irq 106, io mem 0xffffffc0004bf654 [ 7.955518] sunxi-ehci 1c1b000.ehci1-controller: USB 0.0 started, EHCI 1.00 [ 7.969948] hub 2-0:1.0: USB hub found [ 7.980305] hub 2-0:1.0: 1 port detected [ 7.990945] scene_lock_init name=ehci_standby [ 8.002220] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 8.015510] get ohci0-controller drv_vbus_gpio is fail [ 8.027513] get ohci0-controller, regulator_io is no nocare [ 8.040013] [sunxi-ohci0]: probe, pdev->name: 1c1a000.ohci0-controller, sunxi_ohci: 0xffffffc000bd1208 [ 8.056810] sunxi-ohci 1c1a000.ohci0-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 8.072962] sunxi-ohci 1c1a000.ohci0-controller: new USB bus registered, assigned bus number 3 [ 8.089006] sunxi-ohci 1c1a000.ohci0-controller: irq 105, io mem 0x6a626e6b61ff726b [ 8.166610] hub 3-0:1.0: USB hub found [ 8.177127] hub 3-0:1.0: 1 port detected [ 8.187838] scene_lock_init name=ohci_standby [ 8.198930] get ohci1-controller drv_vbus_gpio is fail [ 8.210812] get ohci1-controller, regulator_io is no nocare [ 8.223168] [sunxi-ohci1]: probe, pdev->name: 1c1b000.ohci1-controller, sunxi_ohci: 0xffffffc000bd1458 [ 8.239744] sunxi-ohci 1c1b000.ohci1-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 8.255674] sunxi-ohci 1c1b000.ohci1-controller: new USB bus registered, assigned bus number 4 [ 8.271515] sunxi-ohci 1c1b000.ohci1-controller: irq 107, io mem 0x6a626e6b61ff726b [ 8.343724] hub 4-0:1.0: USB hub found [ 8.354085] hub 4-0:1.0: 1 port detected [ 8.364673] scene_lock_init name=ohci_standby [ 8.376121] usbcore: registered new interface driver usb-storage [ 8.389168] usbcore: registered new interface driver ums-alauda [ 8.402096] usbcore: registered new interface driver ums-cypress [ 8.415047] usbcore: registered new interface driver ums-datafab [ 8.427951] usbcore: registered new interface driver ums_eneub6250 [ 8.441005] usbcore: registered new interface driver ums-freecom [ 8.453821] usbcore: registered new interface driver ums-isd200 [ 8.466544] usbcore: registered new interface driver ums-jumpshot [ 8.479394] usbcore: registered new interface driver ums-karma [ 8.491879] usbcore: registered new interface driver ums-onetouch [ 8.504581] usbcore: registered new interface driver ums-realtek [ 8.517154] usbcore: registered new interface driver ums-sddr09 [ 8.529603] usbcore: registered new interface driver ums-sddr55 [ 8.542012] usbcore: registered new interface driver ums-usbat [ 8.554413] usbcore: registered new interface driver usbserial [ 8.566657] usbcore: registered new interface driver usbserial_generic [ 8.579583] usbserial: USB Serial support registered for generic [ 8.592255] mousedev: PS/2 mouse device common for all mice [ 8.604636] input: sunxi-keyboard as /devices/virtual/input/input0 [ 8.617777] sunxi-rtc 1f00000.rtc: rtc core: registered rtc-sunxi as rtc0 [ 8.630966] sunxi-rtc 1f00000.rtc: RTC enabled [ 8.684300] input: axp81x-supplyer as /devices/platform/axp81x_board/axp81x-supplyer.47/input/input1 [ 8.706970] sunxi budget cooling probe start ! [ 8.717736] CPU freq cooling register Success [ 8.728378] CPU hotplug cooling register Success [ 8.739223] CPU budget cooling register Success [ 8.750153] sunxi gpu cooling probe start ! [ 8.760537] CPU gpu cooling register Success [ 8.773507] cpuidle: using governor ladder [ 8.782746] cpuidle: using governor menu [ 8.792512] sunxi-mmc 1c0f000.sdmmc: SD/MMC/SDIO Host Controller Driver(v0.20 2015-7-13 16:28) Compiled in Apr 23 2016 at 17:56:40 [ 8.810359] sunxi-mmc 1c0f000.sdmmc: regulator prop vmmc,str none [ 8.822006] sunxi-mmc 1c0f000.sdmmc: regulator prop vqmmc,str none [ 8.833676] sunxi-mmc 1c0f000.sdmmc: regulator prop vdmmc,str vcc-sdc [ 8.845719] sunxi-mmc 1c0f000.sdmmc: No vmmc regulator found [ 8.856650] sunxi-mmc 1c0f000.sdmmc: No vqmmc regulator found [ 8.867919] sunxi-mmc 1c0f000.sdmmc: Got CD GPIO #166. [ 8.878270] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 8.893886] sunxi-mmc 1c0f000.sdmmc: no vqmmc,Check if there is regulator [ 8.919837] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 8.939533] sunxi-mmc 1c0f000.sdmmc: base:0xffffff80000ca000 irq:92 [ 8.951536] sunxi-mmc 1c10000.sdmmc: SD/MMC/SDIO Host Controller Driver(v0.20 2015-7-13 16:28) Compiled in Apr 23 2016 at 17:56:40 [ 8.969344] sunxi-mmc 1c10000.sdmmc: Can't get vmmc regulator string [ 8.981206] sunxi-mmc 1c10000.sdmmc: Can't get vqmmc regulator string [ 8.993115] sunxi-mmc 1c10000.sdmmc: Can't get vdmmc regulator string [ 9.004979] get() with no identifier [ 9.013621] get() with no identifier [ 9.022115] get() with no identifier [ 9.030540] sunxi-mmc 1c10000.sdmmc: No vmmc regulator found [ 9.038720] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 52, RTO !! [ 9.039533] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 52, RTO !! [ 9.039548] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 9.041927] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 9.044052] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 5, RTO !! [ 9.044861] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 5, RTO !! [ 9.045670] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 5, RTO !! [ 9.046479] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 5, RTO !! [ 9.047110] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing LEGACY(SDR12) dt B [ 9.047150] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing LEGACY(SDR12) dt B [ 9.049521] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing LEGACY(SDR12) dt B [ 9.074124] mmc0: host does not support reading read-only switch. assuming write-enable. [ 9.075816] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing SD-HS(SDR25) dt B [ 9.075855] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 50000000Hz bm PP pm ON vdd 16 width 1 timing SD-HS(SDR25) dt B [ 9.075946] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 50000000Hz bm PP pm ON vdd 16 width 4 timing SD-HS(SDR25) dt B [ 9.075964] mmc0: new high speed SDHC card at address 0001 [ 9.256947] sunxi-mmc 1c10000.sdmmc: No vqmmc regulator found [ 9.267747] sunxi-mmc 1c10000.sdmmc: No vdmmc regulator found [ 9.278549] mmcblk0: mmc0:0001 00000 29.8 GiB [ 9.288469] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 9.289064] mmcblk0: p1 p2 [ 9.312020] sunxi-mmc 1c10000.sdmmc: no vqmmc,Check if there is regulator [ 9.342954] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 9.372485] sunxi-mmc 1c10000.sdmmc: base:0xffffff80000d2000 irq:93 [ 9.372749] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 52, RE !! [ 9.372771] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 9.375425] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 9.376708] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 8, RE !! [ 9.376733] mmc1: host doesn't support card's voltages [ 9.376737] mmc1: error -22 whilst initialising SDIO card [ 9.376981] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 55, RE !! [ 9.377249] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 55, RE !! [ 9.377276] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 9.377834] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 1, RE !! [ 9.377847] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 0Hz bm OD pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [ 9.532783] usbcore: registered new interface driver usbhid [ 9.544131] usbhid: USB HID core driver [ 9.554707] usbcore: registered new interface driver snd-usb-audio [ 9.568822] sndhdmi sound.7: sndhdmi <-> 1c22800.daudio mapping ok [ 9.582034] TCP: cubic registered [ 9.591202] NET: Registered protocol family 10 [ 9.601952] sit: IPv6 over IPv4 tunneling driver [ 9.612935] NET: Registered protocol family 17 [ 9.623133] Key type dns_resolver registered [ 9.633231] Registering SWP/SWPB emulation handler [ 9.644519] [DISP] boot_disp:0x40a [ 9.654254] [HDMI] power vcc-hdmi-33 [ 9.663849] [HDMI] cec support = 0 [ 9.672853] [DISP] disp_device_attached,line:94:attched ok, mgr0<-->device1, type=4 [ 9.686650] sunxi-rtc 1f00000.rtc: setting system clock to 2010-01-01 00:25:11 UTC (1262305511) [ 9.702421] input: sunxi-ths as /devices/virtual/input/input2 [ 9.714271] thermal thermal_zone0: failed to read out thermal zone 0 [ 9.727003] ALSA device list: [ 9.735479] #0: sndhdmi [ 9.743842] Freeing unused kernel memory: 484K (ffffffc000957000 - ffffffc0009d0000) [ 10.523760] [ehci0-controller]: sunxi_usb_disable_ehci [ 10.534678] [sunxi-ehci0]: remove, pdev->name: 1c1a000.ehci0-controller, sunxi_ehci: 0xffffffc000bd16a8 [ 10.550397] scene_lock_destroy name=ehci_standby [ 10.560839] sunxi-ehci 1c1a000.ehci0-controller: remove, state 4 [ 10.572912] usb usb1: USB disconnect, device number 1 [ 10.584644] sunxi-ehci 1c1a000.ehci0-controller: USB bus 1 deregistered [ 10.597520] [ohci0-controller]: sunxi_usb_disable_ohci [ 10.608763] [sunxi-ohci0]: remove, pdev->name: 1c1a000.ohci0-controller, sunxi_ohci: 0xffffffc000bd1208 [ 10.624878] scene_lock_destroy name=ohci_standby [ 10.635728] sunxi-ohci 1c1a000.ohci0-controller: remove, state 4 [ 10.648198] usb usb3: USB disconnect, device number 1 [ 10.660013] sunxi-ohci 1c1a000.ohci0-controller: USB bus 3 deregistered [ 10.673270] [ehci0-controller]: sunxi_usb_enable_ehci [ 10.684835] [sunxi-ehci0]: probe, pdev->name: 1c1a000.ehci0-controller, sunxi_ehci: 0xffffffc000bd16a8, 0x:ffffff80000ae000, irq_no:68 [ 10.704445] sunxi-ehci 1c1a000.ehci0-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 10.720727] sunxi-ehci 1c1a000.ehci0-controller: new USB bus registered, assigned bus number 1 [ 10.737001] sunxi-ehci 1c1a000.ehci0-controller: irq 104, io mem 0xffffffc0006b0664 [ 10.754775] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities [ 10.769770] sunxi-ehci 1c1a000.ehci0-controller: USB 0.0 started, EHCI 1.00 [ 10.784570] hub 1-0:1.0: USB hub found [ 10.785062] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities [ 10.810554] hub 1-0:1.0: 1 port detected [ 10.821480] scene_lock_init name=ehci_standby [ 10.832696] [ohci0-controller]: sunxi_usb_enable_ohci [ 10.832978] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 10.860334] [sunxi-ohci0]: probe, pdev->name: 1c1a000.ohci0-controller, sunxi_ohci: 0xffffffc000bd1208 [ 10.877280] sunxi-ohci 1c1a000.ohci0-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 10.893495] sunxi-ohci 1c1a000.ohci0-controller: new USB bus registered, assigned bus number 3 [ 10.909595] sunxi-ohci 1c1a000.ohci0-controller: irq 105, io mem 0xffffff9c [ 10.981066] hub 3-0:1.0: USB hub found [ 10.991720] hub 3-0:1.0: 1 port detected [ 11.002651] scene_lock_init name=ohci_standby [ 11.047295] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR) [ 11.068899] systemd[1]: Detected architecture 'arm64'. Welcome to Debian GNU/Linux 8 (jessie)! [ 11.105402] systemd[1]: Set hostname to . [ 11.325484] systemd[1]: [/etc/systemd/system/eth0-mackeeper.service:6] Unknown lvalue 'After' in section 'Service' [ 11.343972] systemd[1]: [/etc/systemd/system/eth0-mackeeper.service:7] Unknown lvalue 'After' in section 'Service' [ 11.377465] systemd[1]: Expecting device dev-ttyS0.device... Expecting device dev-ttyS0.device... [ 11.409469] systemd[1]: Starting Forward Password Requests to Wall Directory Watch. [ 11.424881] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 11.440038] systemd[1]: Starting Remote File Systems (Pre). [ OK ] Reached target Remote File Systems (Pre). [ 11.468446] systemd[1]: Reached target Remote File Systems (Pre). [ 11.481878] systemd[1]: Starting Encrypted Volumes. [ OK ] Reached target Encrypted Volumes. [ 11.517638] systemd[1]: Reached target Encrypted Volumes. [ 11.530271] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch. [ 11.545871] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ 11.561276] systemd[1]: Starting Paths. [ OK ] Reached target Paths. [ 11.586519] systemd[1]: Reached target Paths. [ 11.598016] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [ 11.615120] systemd[1]: Starting Swap. [ OK ] Reached target Swap. [ 11.645557] systemd[1]: Reached target Swap. [ 11.657002] systemd[1]: Expecting device dev-mmcblk0p1.device... Expecting device dev-mmcblk0p1.device... [ 11.684922] systemd[1]: Starting Root Slice. [ OK ] Created slice Root Slice. [ 11.714432] systemd[1]: Created slice Root Slice. [ 11.726423] systemd[1]: Starting User and Session Slice. [ OK ] Created slice User and Session Slice. [ 11.753802] systemd[1]: Created slice User and Session Slice. [ 11.766817] systemd[1]: Starting Delayed Shutdown Socket. [ OK ] Listening on Delayed Shutdown Socket. [ 11.802995] systemd[1]: Listening on Delayed Shutdown Socket. [ 11.815933] systemd[1]: Starting /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ 11.852195] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ 11.866509] systemd[1]: Starting Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 11.901403] systemd[1]: Listening on Journal Socket (/dev/log). [ 11.914496] systemd[1]: Starting udev Control Socket. [ OK ] Listening on udev Control Socket. [ 11.940756] systemd[1]: Listening on udev Control Socket. [ 11.953081] systemd[1]: Starting udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 11.980117] systemd[1]: Listening on udev Kernel Socket. [ 11.992335] systemd[1]: Starting Journal Socket. [ OK ] Listening on Journal Socket. [ 12.019484] systemd[1]: Listening on Journal Socket. [ 12.031277] systemd[1]: Starting System Slice. [ OK ] Created slice System Slice. [ 12.058841] systemd[1]: Created slice System Slice. [ 12.070306] systemd[1]: Started File System Check on Root Device. [ 12.083029] systemd[1]: Starting system-systemd\x2dfsck.slice. [ OK ] Created slice system-systemd\x2dfsck.slice. [ 12.117875] systemd[1]: Created slice system-systemd\x2dfsck.slice. [ 12.130791] systemd[1]: Starting system-getty.slice. [ OK ] Created slice system-getty.slice. [ 12.157243] systemd[1]: Created slice system-getty.slice. [ 12.169004] systemd[1]: Starting system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 12.196602] systemd[1]: Created slice system-serial\x2dgetty.slice. [ 12.209252] systemd[1]: Starting Increase datagram queue length... Starting Increase datagram queue length... [ 12.237477] systemd[1]: Starting Restore / save the current clock... Starting Restore / save the current clock... [ 12.288743] systemd[1]: Starting Create list of required static device nodes for the current kernel... Starting Create list of required static device nodes...rrent kernel... [ 12.338533] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 12.376745] systemd[1]: Started Set Up Additional Binary Formats. [ 12.389322] systemd[1]: Mounting POSIX Message Queue File System... Mounting POSIX Message Queue File System... [ 12.424577] systemd[1]: Mounting Huge Pages File System... Mounting Huge Pages File System... [ 12.454114] systemd[1]: Mounting Debug File System... Mounting Debug File System... [ 12.483536] systemd[1]: Starting udev Coldplug all Devices... Starting udev Coldplug all Devices... [ 12.513238] systemd[1]: Starting Slices. [ OK ] Reached target Slices. [ 12.541168] systemd[1]: Reached target Slices. [ OK ] Mounted Debug File System. [ 12.570630] systemd[1]: Mounted Debug File System. [ OK ] Mounted Huge Pages File System. [ 12.600161] systemd[1]: Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ 12.629659] systemd[1]: Mounted POSIX Message Queue File System. [ OK ] Started Increase datagram queue length. [ 12.659215] systemd[1]: Started Increase datagram queue length. [ OK ] Started Restore / save the current clock. [ 12.688694] systemd[1]: Started Restore / save the current clock. [ OK ] Started Create list of required static device nodes ...current kernel. [ 12.728049] systemd[1]: Started Create list of required static device nodes for the current kernel. [ 12.747633] systemd[1]: Time has been changed [ 12.793046] systemd[1]: Starting Create Static Device Nodes in /dev... Starting Create Static Device Nodes in /dev... [ 12.829666] systemd[1]: Starting Syslog Socket. [ OK ] Listening on Syslog Socket. [ 12.856223] systemd[1]: Listening on Syslog Socket. [ 12.867124] systemd[1]: Starting Journal Service... Starting Journal Service... [ OK ] Started Journal Service. [ 12.900695] cfg80211: Calling CRDA to update world regulatory domain [ 12.915020] systemd[1]: Started Journal Service. [ OK ] Started udev Coldplug all Devices. [ OK ] Started Create Static Device Nod[ 13.055370] RTL871X: module init start es in /dev. [ 13.065394] RTL871X: rtl8723bs v4.3.16_13854.20150410_BTCOEX20150119-5844 [ 13.078917] RTL871X: build time: Apr 23 2016 17:32:18 [ 13.089458] RTL871X: rtl8723bs BT-Coex version = BTCOEX20150119-5844 Starting udev Kernel De[ 13.101383] sunxi-wlan wlan.26: bus_index: 1 vice Manager... [ 13.113851] sunxi-wlan wlan.26: check wlan io_regulator voltage: 1800000 [ 13.149647] systemd-udevd[1434]: starting version 215 [ OK ] Started udev Kernel Device Manager. Starting Copy rules generated while the root was ro... Starting LSB: Tune IDE hard disks... Starting LSB: Set preliminary keymap... [ OK ] Started Copy rules generated while the root was ro. [ 13.235832] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 13.253149] sunxi-mmc 1c10000.sdmmc: no vqmmc,Check if there is regulator [ OK ] Started LSB: Set preliminary keymap. [ 13.266109] RTL871X: module init ret=0 [ 13.279036] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ OK ] Started Load Kernel Modules. [ 13.308761] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 52, RE !! [ 13.320857] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 52, RE !! [ 13.332609] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ OK ] Started LSB: Tune IDE hard dis[ 13.353474] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B ks. [ 13.371731] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 8, RE !! [ 13.383790] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 5, RE !! [ 13.395811] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 5, RE !! Mounting Configuration [ 13.407846] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 5, RE !! File System... [ 13.421914] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 5, RE !! [ 13.434714] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 55, RE !! Starting Apply Kernel V[ 13.446547] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 55, RE !! ariables... [ 13.460656] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 55, RE !! [ 13.473019] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 55, RE !! [ 13.484350] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B Mounting FUSE Control File System... [ 13.501669] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 1, RE !! [ 13.513043] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 0Hz bm OD pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B Starting Remount Root and Kernel File Systems... [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Configuration File System. [ 13.573432] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) [ OK ] Started Apply Kernel Variables. [ OK ] Started Remount Root and Kernel File Systems. [ 13.922761] sunxi cedar version 0.1 [ 13.932126] [cedar]: install start!!! [ 13.941626] ycy the get irq is 90 [ 13.951622] ycy clk_bass_vir 0x18 is ffffff80000fc018, the value:3006207 [ 13.964607] ycy clk_bass_vir 0x13c is ffffff80000fc13c, the value:0 [ 13.976611] ycy clk_bass_vir 0x64 is ffffff80000fc064, the value:601810 [ 13.989360] ycy clk_bass_vir 0x2c4 is ffffff80000fc2c4, the value:601c10 [ 14.001792] ycy clk_bass_vir 0x100 is ffffff80000fc100, the value:0 HELLO! BOOT0 is starting! boot0 commit : 045061a8bb2580cb3fa02e301f52a015040c158f boot0 version : 4.0.0 set pll start set pll end rtc[0] value = 0x00000000 rtc[1] value = 0x00000000 rtc[2] value = 0x00000000 rtc[3] value = 0x00000000 rtc[4] value = 0x00000000 rtc[5] value = 0x00000000 DRAM driver version: V1.1 rsb_send_initseq: rsb clk 400Khz -> 3Mhz PMU: AXP81X ddr voltage = 1500 mv DRAM Type = 3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3) DRAM clk = 672 MHz DRAM zq value: 003b3bbb DRAM single rank full DQ OK DRAM size = 1024 MB DRAM init ok dram size =1024 card boot number = 0, boot0 copy = 0 card no is 0 sdcard 0 line count 4 [mmc]: mmc driver ver 2015-05-08 20:06 [mmc]: sdc0 spd mode error, 2 [mmc]: Wrong media type 0x00000000 [mmc]: ***Try SD card 0*** [mmc]: HSSDR52/SDR25 4 bit [mmc]: 50000000 Hz [mmc]: 30528 MB [mmc]: ***SD/MMC 0 init OK!!!*** sdcard 0 init ok The size of uboot is 000ec000. sum=e99e0b56 src_sum=e99e0b56 Succeed in loading uboot from sdmmc flash. boot0: start load other image boot0: Loading BL3-1 Loading file 0 at address 0x40000000,size 0x00008400 success boot0: Loading scp Loading file 2 at address 0x00040000,size 0x00019c00 success set arisc reset to de-assert state Ready to disable icache. Jump to secend Boot. U-Boot 2014.07-4-pine64-longsleep (Apr 17 2016 - 20:46:05) Allwinner Technology uboot commit : b95bd2301e5765a3866a3447327ecf53deb0270b rsb: secure monitor exist [ 0.336]pmbus: ready [ 0.338][ARISC] :arisc initialize [ 0.669][ARISC] :arisc_dvfs_cfg_vf_table: support only one vf_table [ 0.784][ARISC] :sunxi-arisc driver startup succeeded [ 0.817]PMU: AXP81X [ 0.819]PMU: AXP81X found bat_vol=193, ratio=100 [ 0.826]PMU: dcdc2 1100 [ 0.829]PMU: cpux 1008 Mhz,AXI=336 Mhz PLL6=600 Mhz,AHB1=200 Mhz, APB1=100Mhz AHB2=300Mhz MBus=400Mhz device_type = 3253, onoff=1 dcdc1_vol = 3300, onoff=1 dcdc2_vol = 1100, onoff=1 dcdc6_vol = 1100, onoff=1 aldo1_vol = 2800, onoff=0 aldo2_vol = 1800, onoff=1 aldo3_vol = 3000, onoff=1 dldo1_vol = 3300, onoff=0 dldo2_vol = 3300, onoff=0 dldo3_vol = 2800, onoff=0 dldo4_vol = 3300, onoff=1 eldo1_vol = 1800, onoff=1 eldo2_vol = 1800, onoff=0 eldo3_vol = 1800, onoff=0 fldo1_vol = 1200, onoff=0 fldo2_vol = 1100, onoff=1 gpio0_vol = 3100, onoff=0 vbus not exist no battery, limit to dc run key detect no key found no uart input DRAM: 1008 MiB fdt addr: 0x76ebc080 Relocation Offset is: 35f0e000 In: serial Out: serial Err: serial gic: sec monitor mode [ 1.637]start drv_disp_init init_clocks: finish init_clocks. enable power vcc-hdmi-33, ret=0 drv_disp_init finish boot_disp.output_disp=0 boot_disp.output_type=3 boot_disp.output_type=10 fetch script data boot_disp.auto_hpd fail disp0 device type(4) enable attched ok, mgr0<-->device1, type=4, mode=10 [ 1.986]end workmode = 0,storage type = 1 [ 1.990]MMC: 0 [mmc]: mmc driver ver 2015-06-03 13:50:00 SUNXI SD/MMC: 0 [mmc]: start mmc_calibrate_delay_unit, don't access device... [mmc]: delay chain cal done, sample: 192(ps) [mmc]: media type 0x0 [mmc]: Wrong media type 0x0 [mmc]: ************Try SD card 0************ [mmc]: host caps: 0x27 [mmc]: MID 1b PSN 824c5d4d [mmc]: PNM 00000 -- 0x30-30-30-30-30 [mmc]: PRV 1.0 [mmc]: MDT m-11 y-2015 [mmc]: speed mode : HSSDR52/SDR25 [mmc]: clock : 50000000 Hz [mmc]: bus_width : 4 bit [mmc]: user capacity : 30528 MB [mmc]: ************SD/MMC 0 init OK!!!************ [mmc]: erase_grp_size : 0x1WrBlk*0x200=0x200 Byte [mmc]: secure_feature : 0x0 [mmc]: secure_removal_type : 0x0 [ 2.175]sunxi flash init ok [mmc]: Has init [ 2.207]---drivers/mmc/mmc.c 2733 mmc_init reading uboot.env ** Unable to read "uboot.env" from mmc0:1 ** Using default environment --------fastboot partitions-------- mbr not exist base bootcmd=run mmcbootcmd bootcmd set setargs_mmc key 0 recovery key high 12, low 10 fastboot key high 6, low 4 no misc partition is found to be run cmd=run mmcbootcmd update dtb dram start update dtb dram end serial is: 8400519008005c19014b get Pine64 model from DRAM size DRAM >512M Pine64 model: pine64-plus no battery exist sunxi_bmp_logo_display ** Bad device size - sunxi_flash 0 ** sunxi bmp info error : unable to open logo file bootlogo.bmp [ 2.412]inter uboot shell Hit any key to stop autoboot: 0 [mmc]: Has init [ 5.523]---drivers/mmc/mmc.c 2733 mmc_init reading uEnv.txt [mmc]: blkcnt should not be 0 137 bytes read in 5 ms (26.4 KiB/s) Loading boot environment ... [mmc]: Has init [ 5.542]---drivers/mmc/mmc.c 2733 mmc_init reading boot.scr ** Unable to read file boot.scr ** Booting with defaults ... [mmc]: Has init [ 5.560]---drivers/mmc/mmc.c 2733 mmc_init reading pine64/sun50i-a64-pine64-plus.dtb 69134 bytes read in 10 ms (6.6 MiB/s) [mmc]: Has init [ 5.615]---drivers/mmc/mmc.c 2733 mmc_init reading pine64/Image 11170152 bytes read in 561 ms (19 MiB/s) [mmc]: Has init [ 6.187]---drivers/mmc/mmc.c 2733 mmc_init reading initrd.img 1076058 bytes read in 57 ms (18 MiB/s) Image lacks image_size field, assuming 16MiB ## Flattened Device Tree blob at 45000000 Booting using the fdt blob at 0x45000000 reserving fdt memory region: addr=41010000 size=10000 reserving fdt memory region: addr=41020000 size=800 reserving fdt memory region: addr=40100000 size=4000 reserving fdt memory region: addr=40104000 size=1000 reserving fdt memory region: addr=40105000 size=1000 reserving fdt memory region: addr=45000000 size=11000 Loading Ramdisk to 76dad000, end 76eb3b5a ... OK Loading Device Tree to 44feb000, end 44ffefff ... OK Starting kernel ... [mmc]: MMC Device 2 not found [mmc]: mmc 2 not find, so not exit [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.10.65-7-pine64-longsleep (longsleep@mose2) (gcc version 5.3.1 20160413 (Ubuntu/Linaro 5.3.1-14ubuntu2) ) #28 SMP PREEMPT Sat Apr 23 20:13:25 CEST 2016 [ 0.000000] CPU: AArch64 Processor [410fd034] revision 4 [ 0.000000] Machine: sun50iw1p1 [ 0.000000] cma: CMA: reserved 64 MiB at 7c000000 [ 0.000000] script_init enter! [ 0.000000] script buffer is NULL! [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] PERCPU: Embedded 12 pages/cpu @ffffffc03af98000 s19712 r8192 d21248 u49152 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 254520 [ 0.000000] Kernel command line: console=tty0 console=ttyS0,115200n8 no_console_suspend earlycon=uart,mmio32,0x01c28000 mac_addr=7a:6e:63:ac:21:f1 root=/dev/mmcblk0p2 ro rootwait [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) [ 0.000000] Memory: 1008MB = 1008MB total [ 0.000000] Memory: 937300k/937300k available, 94892k reserved [ 0.000000] Virtual kernel memory layout: [ 0.000000] vmalloc : 0xffffff8000000000 - 0xffffffbbffff0000 (245759 MB) [ 0.000000] vmemmap : 0xffffffbc00e38000 - 0xffffffbc01c00000 ( 13 MB) [ 0.000000] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc03f000000 ( 1008 MB) [ 0.000000] .init : 0xffffffc000957000 - 0xffffffc0009d0d00 ( 488 kB) [ 0.000000] .text : 0xffffffc000080000 - 0xffffffc0009569b4 ( 9051 kB) [ 0.000000] .data : 0xffffffc0009d1000 - 0xffffffc000b27168 ( 1369 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] allocated 4194304 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 6.860846] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 6.860877] pid_max: default: 32768 minimum: 301 [ 6.860979] Security Framework initialized [ 6.861013] AppArmor: AppArmor initialized [ 6.861057] Mount-cache hash table entries: 256 [ 6.871472] Initializing cgroup subsys memory [ 6.871532] Initializing cgroup subsys devices [ 6.871549] Initializing cgroup subsys freezer [ 6.871565] Initializing cgroup subsys blkio [ 6.871581] Initializing cgroup subsys perf_event [ 6.871602] Initializing cgroup subsys hugetlb [ 6.871654] ftrace: allocating 25847 entries in 101 pages [ 6.901839] CPU0: update cpu_power 1968128 [ 6.901874] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available [ 6.902796] virtual base = 0xffffff800000a000. [ 6.902816] gicd_base = 0xffffff800000c000. [ 6.902829] gicc_base = 0xffffff800000e000. [ 6.903392] CPU1: Booted secondary processor [ 6.903415] CPU1: update cpu_power 1968128 [ 6.906019] CPU2: Booted secondary processor [ 6.906030] CPU2: update cpu_power 1968128 [ 6.910137] CPU3: Booted secondary processor [ 6.910148] CPU3: update cpu_power 1968128 [ 6.910226] Brought up 4 CPUs [ 6.910302] SMP: Total of 4 processors activated (192.00 BogoMIPS). [ 6.910833] devtmpfs: initialized [ 6.915626] atomic64 test passed [ 6.915647] pinctrl core: initialized pinctrl subsystem [ 6.918620] NET: Registered protocol family 16 [ 6.918935] script_sysfs_init success [ 6.919776] dump_class_init,806, success [ 6.920415] vdso: 2 pages (1 code, 1 data) at base ffffffc0009d9000 [ 6.920448] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 6.921757] software IO TLB [mem 0x79c00000-0x7a000000] (4MB) mapped at [ffffffc038c00000-ffffffc038ffffff] [ 6.922693] DMA: preallocated 256 KiB pool for atomic allocations [ 6.922875] Serial: AMBA PL011 UART driver [ 6.923240] axp81x_board_init: axp regl_devs num = 23 [ 6.923453] pll_audio-set_default_rate=24576000 success! [ 6.923484] pll_video0-set_default_rate=297000000 success! [ 6.923568] pll_video1-set_default_rate=297000000 success! [ 6.923636] pll_de-set_default_rate=297000000 success! [ 6.924365] de-set_default_source=pll_de success! [ 6.924382] de-set_default_rate=297000000 success! [ 6.924435] tcon0-set_default_source=pll_mipi success! [ 6.924477] tcon1-set_default_source=pll_video0 success! [ 6.924709] hdmi-set_default_source=pll_video0 success! [ 6.927267] sun50i-r-pinctrl 1f02c00.pinctrl: initialized sunXi PIO driver [ 6.927515] [sun50iw1p1_pinctrl_probe][838] [ 6.929266] sun50i-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver [ 6.930554] sunxi hwspinlock vbase:0xffffff800005c000 [ 6.940467] sunxi_chipid_probe,150: soc bin:0 [ 6.957600] bio: create slab at 0 [ 6.958029] pwm module init! [ 6.960330] SCSI subsystem initialized [ 6.960810] usbcore: registered new interface driver usbfs [ 6.960927] usbcore: registered new interface driver hub [ 6.961063] usbcore: registered new device driver usb [ 6.962351] Linux video capture interface: v2.00 [ 6.963275] [ARISC] :sunxi-arisc driver v1.10 [ 6.975006] [ARISC] :sunxi-arisc driver v1.10 startup succeeded [ 6.975409] Advanced Linux Sound Architecture Driver Initialized. [ 6.975980] NetLabel: Initializing [ 6.975994] NetLabel: domain hash size = 128 [ 6.976007] NetLabel: protocols = UNLABELED CIPSOv4 [ 6.976051] NetLabel: unlabeled traffic allowed by default [ 6.976301] [pm]aw_pm_init! [ 6.976384] rtc physical base = 0x0000000001f00000 . [ 6.976430] np name = /soc@01c00000/rtc@01f00000. [ 6.976445] base = ffffff8000070100, len = 4. [ 6.976458] pmu name: pmu0 . [ 6.976502] pmu0_enable = 0x1. [ 6.976515] pmux_id = 0x6. [ 6.976527] pmux_twi_id = 0x1. [ 6.976539] pmux_twi_addr = 0x34. [ 6.976550] pmu name: pmu1 . [ 6.976608] Warning: can not find np for pmu1. [ 6.976843] add_sys_pwr_dm: get ldo name for id: vcc-lpddr failed [ 6.977009] after inited: sys_mask config = 0x4a55. [ 6.977042] Warning: can not find np for dynamic_standby_para. [ 6.977181] [pm]valid [ 6.977190] [pm]valid [ 6.977200] Notice: sun9i&sun8iw5&sun50i not need support normal standby, change to super standby. [ 6.977396] Switching to clocksource arch_sys_counter [ 6.987948] AppArmor: AppArmor Filesystem Enabled [ 7.000341] NET: Registered protocol family 2 [ 7.000990] TCP established hash table entries: 8192 (order: 5, 131072 bytes) [ 7.001134] TCP bind hash table entries: 8192 (order: 5, 131072 bytes) [ 7.001284] TCP: Hash tables configured (established 8192 bind 8192) [ 7.001366] TCP: reno registered [ 7.001383] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 7.001423] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 7.001642] NET: Registered protocol family 1 [ 7.001903] RPC: Registered named UNIX socket transport module. [ 7.001921] RPC: Registered udp transport module. [ 7.001935] RPC: Registered tcp transport module. [ 7.001948] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 7.002107] Unpacking initramfs... [ 7.045709] Freeing initrd memory: 1048K (ffffffc035dad000 - ffffffc035eb3000) [ 7.046433] kvm [1]: Using HYP init bounce page @7aa99000 [ 7.046907] kvm [1]: interrupt-controller@1c84000 IRQ25 [ 7.047254] kvm [1]: timer IRQ27 [ 7.047273] kvm [1]: Hyp mode initialized successfully [ 7.048634] lock super standby defaultly! [ 7.048659] lookup_scene_lock_name: new scene lock super_standby [ 7.048675] scene_lock_init name=super_standby [ 7.048690] scene_lock: super_standby, type 5, count 1 [ 7.049355] audit: initializing netlink socket (disabled) [ 7.049413] type=2000 audit(0.170:1): initialized [ 7.050298] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 7.050751] VFS: Disk quotas dquot_6.5.2 [ 7.050874] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 7.051295] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 7.051691] NFS: Registering the id_resolver key type [ 7.051739] Key type id_resolver registered [ 7.051753] Key type id_legacy registered [ 7.051773] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 7.051928] NTFS driver 2.1.30 [Flags: R/W]. [ 7.052196] fuse init (API version 7.22) [ 7.052592] msgmni has been set to 1960 [ 7.053380] io scheduler noop registered [ 7.053397] io scheduler deadline registered [ 7.053441] io scheduler cfq registered (default) [ 7.054250] [DISP]disp_module_init [ 7.054807] [DISP] boot_disp:0x40a [ 7.055387] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail [ 7.055547] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail [ 7.055704] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail [ 7.056831] [DISP] fb_base:0x47400000 [ 7.064388] [DISP] Fb_map_kernel_logo,line:885:this is not a bmp picture. [ 7.094266] Console: switching to colour frame buffer device 240x67 [ 7.123215] [DISP]disp_module_init finish [ 7.123745] uart0: ttyS0 at MMIO 0x1c28000 (irq = 32) is a SUNXI [ 7.123901] sw_console_setup()1173 - console setup baud 115200 parity n bits 8, flow n [ 8.083134] console [ttyS0] enabled [ 8.087575] uart1: ttyS1 at MMIO 0x1c28400 (irq = 33) is a SUNXI [ 8.094611] uart2: ttyS2 at MMIO 0x1c28800 (irq = 34) is a SUNXI [ 8.101716] uart3: ttyS3 at MMIO 0x1c28c00 (irq = 35) is a SUNXI [ 8.108775] uart4: ttyS4 at MMIO 0x1c29000 (irq = 36) is a SUNXI [ 8.115987] misc dump reg init [ 8.119739] [drm] Initialized drm 1.1.0 20060810 [ 8.128368] loop: module loaded [ 8.132153] sunxi-bt bt.27: Missing bt_power. [ 8.137011] sunxi-bt bt.27: bt_power_name ((null)) [ 8.142366] sunxi-bt bt.27: io_regulator_name (vcc-wifi-io) [ 8.148613] sunxi-bt bt.27: bt_rst gpio=356 mul-sel=1 pull=-1 drv_level=-1 data=0 [ 8.157373] sunxi-bt bt.27: clk not config [ 8.162078] sunxi-bt bt.27: block state already is 1 [ 8.167896] sunxi-wlan wlan.26: wlan_busnum (1) [ 8.172956] sunxi-wlan wlan.26: Missing wlan_power. [ 8.178397] sunxi-wlan wlan.26: wlan_power_name ((null)) [ 8.184316] sunxi-wlan wlan.26: io_regulator_name (vcc-wifi-io) [ 8.190940] sunxi-wlan wlan.26: wlan_regon gpio=354 mul-sel=1 pull=-1 drv_level=-1 data=0 [ 8.200476] sunxi-wlan wlan.26: wlan_hostwake gpio=355 mul-sel=6 pull=-1 drv_level=-1 data=0 [ 8.210289] sunxi-wlan wlan.26: clk not config [ 8.215884] tun: Universal TUN/TAP device driver, 1.6 [ 8.221524] tun: (C) 1999-2004 Max Krasnyansky [ 8.229122] WARNING: Get ephy clock is failed [ 8.234604] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.242048] get ehci0-controller drv_vbus_gpio is fail [ 8.247784] get ehci0-controller, regulator_io is no nocare [ 8.254042] [sunxi-ehci0]: probe, pdev->name: 1c1a000.ehci0-controller, sunxi_ehci: 0xffffffc000bd16a8, 0x:ffffff80000ae000, irq_no:68 [ 8.267565] sunxi-ehci 1c1a000.ehci0-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.277672] sunxi-ehci 1c1a000.ehci0-controller: new USB bus registered, assigned bus number 1 [ 8.287563] sunxi-ehci 1c1a000.ehci0-controller: irq 104, io mem 0xffffffc0004bf654 [ 8.315702] sunxi-ehci 1c1a000.ehci0-controller: USB 0.0 started, EHCI 1.00 [ 8.324044] hub 1-0:1.0: USB hub found [ 8.328242] hub 1-0:1.0: 1 port detected [ 8.338734] scene_lock_init name=ehci_standby [ 8.349596] get ehci1-controller drv_vbus_gpio is fail [ 8.361201] get ehci1-controller, regulator_io is no nocare [ 8.373273] [sunxi-ehci1]: probe, pdev->name: 1c1b000.ehci1-controller, sunxi_ehci: 0xffffffc000bd18f8, 0x:ffffff80000b6000, irq_no:6a [ 8.392741] sunxi-ehci 1c1b000.ehci1-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.408939] sunxi-ehci 1c1b000.ehci1-controller: new USB bus registered, assigned bus number 2 [ 8.424968] sunxi-ehci 1c1b000.ehci1-controller: irq 106, io mem 0xffffffc0004bf654 [ 8.453461] sunxi-ehci 1c1b000.ehci1-controller: USB 0.0 started, EHCI 1.00 [ 8.467881] hub 2-0:1.0: USB hub found [ 8.478238] hub 2-0:1.0: 1 port detected [ 8.488880] scene_lock_init name=ehci_standby [ 8.500159] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 8.513445] get ohci0-controller drv_vbus_gpio is fail [ 8.525450] get ohci0-controller, regulator_io is no nocare [ 8.537953] [sunxi-ohci0]: probe, pdev->name: 1c1a000.ohci0-controller, sunxi_ohci: 0xffffffc000bd1208 [ 8.554754] sunxi-ohci 1c1a000.ohci0-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 8.570912] sunxi-ohci 1c1a000.ohci0-controller: new USB bus registered, assigned bus number 3 [ 8.586962] sunxi-ohci 1c1a000.ohci0-controller: irq 105, io mem 0x6a626e6b61ff726b [ 8.664557] hub 3-0:1.0: USB hub found [ 8.675080] hub 3-0:1.0: 1 port detected [ 8.685795] scene_lock_init name=ohci_standby [ 8.696888] get ohci1-controller drv_vbus_gpio is fail [ 8.708773] get ohci1-controller, regulator_io is no nocare [ 8.721130] [sunxi-ohci1]: probe, pdev->name: 1c1b000.ohci1-controller, sunxi_ohci: 0xffffffc000bd1458 [ 8.737706] sunxi-ohci 1c1b000.ohci1-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 8.753638] sunxi-ohci 1c1b000.ohci1-controller: new USB bus registered, assigned bus number 4 [ 8.769488] sunxi-ohci 1c1b000.ohci1-controller: irq 107, io mem 0x6a626e6b61ff726b [ 8.841671] hub 4-0:1.0: USB hub found [ 8.852034] hub 4-0:1.0: 1 port detected [ 8.862630] scene_lock_init name=ohci_standby [ 8.874084] usbcore: registered new interface driver usb-storage [ 8.887135] usbcore: registered new interface driver ums-alauda [ 8.900067] usbcore: registered new interface driver ums-cypress [ 8.913024] usbcore: registered new interface driver ums-datafab [ 8.925933] usbcore: registered new interface driver ums_eneub6250 [ 8.938994] usbcore: registered new interface driver ums-freecom [ 8.951816] usbcore: registered new interface driver ums-isd200 [ 8.964541] usbcore: registered new interface driver ums-jumpshot [ 8.977392] usbcore: registered new interface driver ums-karma [ 8.989880] usbcore: registered new interface driver ums-onetouch [ 9.002588] usbcore: registered new interface driver ums-realtek [ 9.015169] usbcore: registered new interface driver ums-sddr09 [ 9.027625] usbcore: registered new interface driver ums-sddr55 [ 9.040037] usbcore: registered new interface driver ums-usbat [ 9.052447] usbcore: registered new interface driver usbserial [ 9.064697] usbcore: registered new interface driver usbserial_generic [ 9.077623] usbserial: USB Serial support registered for generic [ 9.090303] mousedev: PS/2 mouse device common for all mice [ 9.102693] input: sunxi-keyboard as /devices/virtual/input/input0 [ 9.115843] sunxi-rtc 1f00000.rtc: rtc core: registered rtc-sunxi as rtc0 [ 9.129026] sunxi-rtc 1f00000.rtc: RTC enabled [ 9.182239] input: axp81x-supplyer as /devices/platform/axp81x_board/axp81x-supplyer.47/input/input1 [ 9.204928] sunxi budget cooling probe start ! [ 9.215692] CPU freq cooling register Success [ 9.226339] CPU hotplug cooling register Success [ 9.237183] CPU budget cooling register Success [ 9.248109] sunxi gpu cooling probe start ! [ 9.258489] CPU gpu cooling register Success [ 9.271461] cpuidle: using governor ladder [ 9.280704] cpuidle: using governor menu [ 9.290472] sunxi-mmc 1c0f000.sdmmc: SD/MMC/SDIO Host Controller Driver(v0.20 2015-7-13 16:28) Compiled in Apr 23 2016 at 17:56:40 [ 9.308326] sunxi-mmc 1c0f000.sdmmc: regulator prop vmmc,str none [ 9.319971] sunxi-mmc 1c0f000.sdmmc: regulator prop vqmmc,str none [ 9.331634] sunxi-mmc 1c0f000.sdmmc: regulator prop vdmmc,str vcc-sdc [ 9.343674] sunxi-mmc 1c0f000.sdmmc: No vmmc regulator found [ 9.354604] sunxi-mmc 1c0f000.sdmmc: No vqmmc regulator found [ 9.365870] sunxi-mmc 1c0f000.sdmmc: Got CD GPIO #166. [ 9.376215] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 9.391847] sunxi-mmc 1c0f000.sdmmc: no vqmmc,Check if there is regulator [ 9.417780] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 9.437477] sunxi-mmc 1c0f000.sdmmc: base:0xffffff80000ca000 irq:92 [ 9.449476] sunxi-mmc 1c10000.sdmmc: SD/MMC/SDIO Host Controller Driver(v0.20 2015-7-13 16:28) Compiled in Apr 23 2016 at 17:56:40 [ 9.467278] sunxi-mmc 1c10000.sdmmc: Can't get vmmc regulator string [ 9.479135] sunxi-mmc 1c10000.sdmmc: Can't get vqmmc regulator string [ 9.491037] sunxi-mmc 1c10000.sdmmc: Can't get vdmmc regulator string [ 9.502898] get() with no identifier [ 9.511529] get() with no identifier [ 9.520012] get() with no identifier [ 9.528426] sunxi-mmc 1c10000.sdmmc: No vmmc regulator found [ 9.536662] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 52, RTO !! [ 9.537475] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 52, RTO !! [ 9.537490] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 9.539871] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 9.541996] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 5, RTO !! [ 9.542805] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 5, RTO !! [ 9.543614] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 5, RTO !! [ 9.544423] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 5, RTO !! [ 9.545051] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing LEGACY(SDR12) dt B [ 9.545091] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing LEGACY(SDR12) dt B [ 9.547462] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing LEGACY(SDR12) dt B [ 9.572068] mmc0: host does not support reading read-only switch. assuming write-enable. [ 9.573760] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing SD-HS(SDR25) dt B [ 9.573800] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 50000000Hz bm PP pm ON vdd 16 width 1 timing SD-HS(SDR25) dt B [ 9.573891] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 50000000Hz bm PP pm ON vdd 16 width 4 timing SD-HS(SDR25) dt B [ 9.573909] mmc0: new high speed SDHC card at address 0001 [ 9.585388] mmcblk0: mmc0:0001 00000 29.8 GiB [ 9.764054] sunxi-mmc 1c10000.sdmmc: No vqmmc regulator found [ 9.764897] mmcblk0: p1 p2 [ 9.782522] sunxi-mmc 1c10000.sdmmc: No vdmmc regulator found [ 9.793979] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 9.809801] sunxi-mmc 1c10000.sdmmc: no vqmmc,Check if there is regulator [ 9.840894] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 9.870426] sunxi-mmc 1c10000.sdmmc: base:0xffffff80000da000 irq:93 [ 9.870694] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 52, RE !! [ 9.870718] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 9.873372] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 9.874656] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 8, RE !! [ 9.874682] mmc1: host doesn't support card's voltages [ 9.874686] mmc1: error -22 whilst initialising SDIO card [ 9.874931] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 55, RE !! [ 9.875199] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 55, RE !! [ 9.875228] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 9.875784] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 1, RE !! [ 9.875799] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 0Hz bm OD pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [ 10.030573] usbcore: registered new interface driver usbhid [ 10.041934] usbhid: USB HID core driver [ 10.052542] usbcore: registered new interface driver snd-usb-audio [ 10.066685] sndhdmi sound.7: sndhdmi <-> 1c22800.daudio mapping ok [ 10.079889] TCP: cubic registered [ 10.089027] NET: Registered protocol family 10 [ 10.099760] sit: IPv6 over IPv4 tunneling driver [ 10.110720] NET: Registered protocol family 17 [ 10.120893] Key type dns_resolver registered [ 10.130955] Registering SWP/SWPB emulation handler [ 10.142229] [DISP] boot_disp:0x40a [ 10.151940] [HDMI] power vcc-hdmi-33 [ 10.161531] [HDMI] cec support = 0 [ 10.170562] [DISP] disp_device_attached,line:94:attched ok, mgr0<-->device1, type=4 [ 10.185136] sunxi-rtc 1f00000.rtc: setting system clock to 2010-01-01 00:25:26 UTC (1262305526) [ 10.200851] input: sunxi-ths as /devices/virtual/input/input2 [ 10.212704] thermal thermal_zone0: failed to read out thermal zone 0 [ 10.225429] ALSA device list: [ 10.233917] #0: sndhdmi [ 10.242310] Freeing unused kernel memory: 484K (ffffffc000957000 - ffffffc0009d0000) [ 11.021703] [ehci0-controller]: sunxi_usb_disable_ehci [ 11.032619] [sunxi-ehci0]: remove, pdev->name: 1c1a000.ehci0-controller, sunxi_ehci: 0xffffffc000bd16a8 [ 11.048333] scene_lock_destroy name=ehci_standby [ 11.058778] sunxi-ehci 1c1a000.ehci0-controller: remove, state 4 [ 11.070853] usb usb1: USB disconnect, device number 1 [ 11.082576] sunxi-ehci 1c1a000.ehci0-controller: USB bus 1 deregistered [ 11.095467] [ohci0-controller]: sunxi_usb_disable_ohci [ 11.106711] [sunxi-ohci0]: remove, pdev->name: 1c1a000.ohci0-controller, sunxi_ohci: 0xffffffc000bd1208 [ 11.122827] scene_lock_destroy name=ohci_standby [ 11.133679] sunxi-ohci 1c1a000.ohci0-controller: remove, state 4 [ 11.146155] usb usb3: USB disconnect, device number 1 [ 11.157993] sunxi-ohci 1c1a000.ohci0-controller: USB bus 3 deregistered [ 11.171248] [ehci0-controller]: sunxi_usb_enable_ehci [ 11.182823] [sunxi-ehci0]: probe, pdev->name: 1c1a000.ehci0-controller, sunxi_ehci: 0xffffffc000bd16a8, 0x:ffffff80000ae000, irq_no:68 [ 11.202429] sunxi-ehci 1c1a000.ehci0-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 11.218724] sunxi-ehci 1c1a000.ehci0-controller: new USB bus registered, assigned bus number 1 [ 11.235051] sunxi-ehci 1c1a000.ehci0-controller: irq 104, io mem 0xffffffc0006b0664 [ 11.255266] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities [ 11.267705] sunxi-ehci 1c1a000.ehci0-controller: USB 0.0 started, EHCI 1.00 [ 11.285318] hub 1-0:1.0: USB hub found [ 11.285565] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities [ 11.311273] hub 1-0:1.0: 1 port detected [ 11.322199] scene_lock_init name=ehci_standby [ 11.322322] EXT4-fs (mmcblk0p2): recovery complete [ 11.324203] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 11.360622] [ohci0-controller]: sunxi_usb_enable_ohci [ 11.372692] [sunxi-ohci0]: probe, pdev->name: 1c1a000.ohci0-controller, sunxi_ohci: 0xffffffc000bd1208 [ 11.389561] sunxi-ohci 1c1a000.ohci0-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 11.405748] sunxi-ohci 1c1a000.ohci0-controller: new USB bus registered, assigned bus number 3 [ 11.421874] sunxi-ohci 1c1a000.ohci0-controller: irq 105, io mem 0xffffffc00019fc5c [ 11.498625] hub 3-0:1.0: USB hub found [ 11.509352] hub 3-0:1.0: 1 port detected [ 11.520244] scene_lock_init name=ohci_standby [ 11.538621] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR) [ 11.560192] systemd[1]: Detected architecture 'arm64'. Welcome to Debian GNU/Linux 8 (jessie)! [ 11.603320] systemd[1]: Set hostname to . [ 11.823335] systemd[1]: [/etc/systemd/system/eth0-mackeeper.service:6] Unknown lvalue 'After' in section 'Service' [ 11.841650] systemd[1]: [/etc/systemd/system/eth0-mackeeper.service:7] Unknown lvalue 'After' in section 'Service' [ 11.875231] systemd[1]: Expecting device dev-ttyS0.device... Expecting device dev-ttyS0.device... [ 11.907384] systemd[1]: Starting Forward Password Requests to Wall Directory Watch. [ 11.922810] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 11.937980] systemd[1]: Starting Remote File Systems (Pre). [ OK ] Reached target Remote File Systems (Pre). [ 11.966388] systemd[1]: Reached target Remote File Systems (Pre). [ 11.979823] systemd[1]: Starting Encrypted Volumes. [ OK ] Reached target Encrypted Volumes. [ 12.015581] systemd[1]: Reached target Encrypted Volumes. [ 12.028195] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch. [ 12.043815] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ 12.059255] systemd[1]: Starting Paths. [ OK ] Reached target Paths. [ 12.084460] systemd[1]: Reached target Paths. [ 12.096004] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [ 12.113152] systemd[1]: Starting Swap. [ OK ] Reached target Swap. [ 12.143499] systemd[1]: Reached target Swap. [ 12.154990] systemd[1]: Expecting device dev-mmcblk0p1.device... Expecting device dev-mmcblk0p1.device... [ 12.182876] systemd[1]: Starting Root Slice. [ OK ] Created slice Root Slice. [ 12.212374] systemd[1]: Created slice Root Slice. [ 12.224356] systemd[1]: Starting User and Session Slice. [ OK ] Created slice User and Session Slice. [ 12.251744] systemd[1]: Created slice User and Session Slice. [ 12.264725] systemd[1]: Starting Delayed Shutdown Socket. [ OK ] Listening on Delayed Shutdown Socket. [ 12.300936] systemd[1]: Listening on Delayed Shutdown Socket. [ 12.313885] systemd[1]: Starting /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ 12.350135] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ 12.364435] systemd[1]: Starting Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 12.399346] systemd[1]: Listening on Journal Socket (/dev/log). [ 12.412392] systemd[1]: Starting udev Control Socket. [ OK ] Listening on udev Control Socket. [ 12.438697] systemd[1]: Listening on udev Control Socket. [ 12.451043] systemd[1]: Starting udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 12.478056] systemd[1]: Listening on udev Kernel Socket. [ 12.490271] systemd[1]: Starting Journal Socket. [ OK ] Listening on Journal Socket. [ 12.517422] systemd[1]: Listening on Journal Socket. [ 12.529165] systemd[1]: Starting System Slice. [ OK ] Created slice System Slice. [ 12.556780] systemd[1]: Created slice System Slice. [ 12.568283] systemd[1]: Started File System Check on Root Device. [ 12.581045] systemd[1]: Starting system-systemd\x2dfsck.slice. [ OK ] Created slice system-systemd\x2dfsck.slice. [ 12.615820] systemd[1]: Created slice system-systemd\x2dfsck.slice. [ 12.628736] systemd[1]: Starting system-getty.slice. [ OK ] Created slice system-getty.slice. [ 12.655188] systemd[1]: Created slice system-getty.slice. [ 12.666848] systemd[1]: Starting system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 12.694543] systemd[1]: Created slice system-serial\x2dgetty.slice. [ 12.707215] systemd[1]: Starting Increase datagram queue length... Starting Increase datagram queue length... [ 12.735433] systemd[1]: Starting Restore / save the current clock... Starting Restore / save the current clock... [ 12.786516] systemd[1]: Starting Create list of required static device nodes for the current kernel... Starting Create list of required static device nodes...rrent kernel... [ 12.852394] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 12.884530] systemd[1]: Started Set Up Additional Binary Formats. [ 12.897002] systemd[1]: Mounting POSIX Message Queue File System... Mounting POSIX Message Queue File System... [ 12.932412] systemd[1]: Mounting Huge Pages File System... Mounting Huge Pages File System... [ 12.961947] systemd[1]: Mounting Debug File System... Mounting Debug File System... [ 12.991339] systemd[1]: Starting udev Coldplug all Devices... Starting udev Coldplug all Devices... [ 13.020937] systemd[1]: Starting Slices. [ OK ] Reached target Slices. [ 13.048902] systemd[1]: Reached target Slices. [ OK ] Mounted Debug File System. [ 13.078406] systemd[1]: Mounted Debug File System. [ OK ] Mounted Huge Pages File System. [ 13.107954] systemd[1]: Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ 13.137459] systemd[1]: Mounted POSIX Message Queue File System. [ OK ] Started Increase datagram queue length. [ 13.167029] systemd[1]: Started Increase datagram queue length. [ OK ] Started Restore / save the current clock. [ 13.196465] systemd[1]: Started Restore / save the current clock. [ OK ] Started Create list of required static device nodes ...current kernel. [ 13.235887] systemd[1]: Started Create list of required static device nodes for the current kernel. [ 13.255424] systemd[1]: Time has been changed [ 13.301478] systemd[1]: Starting Create Static Device Nodes in /dev... Starting Create Static Device Nodes in /dev... [ 13.337014] systemd[1]: Starting Syslog Socket. [ OK ] Listening on Syslog Socket. [ 13.363808] systemd[1]: Listening on Syslog Socket. [ 13.374513] systemd[1]: Starting Journal Service... Starting Journal Service... [ OK ] Started Journal Service. [ 13.407883] cfg80211: Calling CRDA to update world regulatory domain [ 13.422849] systemd[1]: Started Journal Service. [ OK ] Started udev Coldplug all Devices. [ OK ] Started Create Static Device Nodes in /dev. Starting udev Kernel Device Manager... [ 13.565189] RTL871X: module init start [ 13.571662] systemd-udevd[1433]: starting version 215 [ 13.584659] RTL871X: rtl8723bs v4.3.16_13854.20150410_BTCOEX20150119-5844 [ OK ] Started udev Kernel Device Manager. [ 13.597101] RTL871X: build time: Apr 23 2016 17:32:18 [ 13.607720] RTL871X: rtl8723bs BT-Coex version = BTCOEX20150119-5844 [ 13.619704] sunxi-wlan wlan.26: bus_index: 1 Starting Copy rules generated while the root was ro... [ 13.629530] sunxi-wlan wlan.26: check wlan io_regulator voltage: 1800000 Starting LSB: Tune IDE hard disks... Starting LSB: Set preliminary keymap... [ OK ] Started Copy rules generated while the root was ro. [ OK ] Started LSB: Set preliminary keymap. Starting Remount Root and Kernel File Systems... [ 13.750903] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 13.751136] RTL871X: module init ret=0 [ 13.776928] sunxi-mmc 1c10000.sdmmc: no vqmmc,Check if there is regulator [ OK ] Started LSB: Tune IDE hard disks. [ 13.806481] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ OK ] Started Load Kernel Modules. [ 13.842337] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) [ 13.846123] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 52, RE !! [ 13.846402] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 52, RE !! [ 13.846419] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B HELLO! BOOT0 is starting! boot0 commit : 045061a8bb2580cb3fa02e301f52a015040c158f boot0 version : 4.0.0 set pll start set pll end rtc[0] value = 0x00000000 rtc[1] value = 0x00000000 rtc[2] value = 0x00000000 rtc[3] value = 0x00000000 rtc[4] value = 0x00000000 rtc[5] value = 0x00000000 DRAM driver version: V1.1 rsb_send_initseq: rsb clk 400Khz -> 3Mhz PMU: AXP81X ddr voltage = 1500 mv DRAM Type = 3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3) DRAM clk = 672 MHz DRAM zq value: 003b3bbb DRAM single rank full DQ OK DRAM size = 1024 MB DRAM init ok dram size =1024 card boot number = 0, boot0 copy = 0 card no is 0 sdcard 0 line count 4 [mmc]: mmc driver ver 2015-05-08 20:06 [mmc]: sdc0 spd mode error, 2 [mmc]: Wrong media type 0x00000000 [mmc]: ***Try SD card 0*** [mmc]: HSSDR52/SDR25 4 bit [mmc]: 50000000 Hz [mmc]: 30528 MB [mmc]: ***SD/MMC 0 init OK!!!*** sdcard 0 init ok The size of uboot is 000ec000. sum=e99e0b56 src_sum=e99e0b56 Succeed in loading uboot from sdmmc flash. boot0: start load other image boot0: Loading BL3-1 Loading file 0 at address 0x40000000,size 0x00008400 success boot0: Loading scp Loading file 2 at address 0x00040000,size 0x00019c00 success set arisc reset to de-assert state Ready to disable icache. Jump to secend Boot. U-Boot 2014.07-4-pine64-longsleep (Apr 17 2016 - 20:46:05) Allwinner Technology uboot commit : b95bd2301e5765a3866a3447327ecf53deb0270b rsb: secure monitor exist [ 0.336]pmbus: ready [ 0.338][ARISC] :arisc initialize [ 0.669][ARISC] :arisc_dvfs_cfg_vf_table: support only one vf_table [ 0.784][ARISC] :sunxi-arisc driver startup succeeded [ 0.817]PMU: AXP81X [ 0.819]PMU: AXP81X found bat_vol=167, ratio=100 [ 0.826]PMU: dcdc2 1100 [ 0.829]PMU: cpux 1008 Mhz,AXI=336 Mhz PLL6=600 Mhz,AHB1=200 Mhz, APB1=100Mhz AHB2=300Mhz MBus=400Mhz device_type = 3253, onoff=1 dcdc1_vol = 3300, onoff=1 dcdc2_vol = 1100, onoff=1 dcdc6_vol = 1100, onoff=1 aldo1_vol = 2800, onoff=0 aldo2_vol = 1800, onoff=1 aldo3_vol = 3000, onoff=1 dldo1_vol = 3300, onoff=0 dldo2_vol = 3300, onoff=0 dldo3_vol = 2800, onoff=0 dldo4_vol = 3300, onoff=1 eldo1_vol = 1800, onoff=1 eldo2_vol = 1800, onoff=0 eldo3_vol = 1800, onoff=0 fldo1_vol = 1200, onoff=0 fldo2_vol = 1100, onoff=1 gpio0_vol = 3100, onoff=0 vbus not exist no battery, limit to dc run key detect no key found 0x20 DRAM: 1008 MiB fdt addr: 0x76ebc080 Relocation Offset is: 35f0e000 In: serial Out: serial Err: serial gic: sec monitor mode [ 1.636]start drv_disp_init init_clocks: finish init_clocks. enable power vcc-hdmi-33, ret=0 drv_disp_init finish boot_disp.output_disp=0 boot_disp.output_type=3 boot_disp.output_type=10 fetch script data boot_disp.auto_hpd fail disp0 device type(4) enable attched ok, mgr0<-->device1, type=4, mode=10 [ 1.986]end workmode = 0,storage type = 1 [ 1.990]MMC: 0 [mmc]: mmc driver ver 2015-06-03 13:50:00 SUNXI SD/MMC: 0 [mmc]: start mmc_calibrate_delay_unit, don't access device... [mmc]: delay chain cal done, sample: 192(ps) [mmc]: media type 0x0 [mmc]: Wrong media type 0x0 [mmc]: ************Try SD card 0************ [mmc]: host caps: 0x27 [mmc]: MID 1b PSN 824c5d4d [mmc]: PNM 00000 -- 0x30-30-30-30-30 [mmc]: PRV 1.0 [mmc]: MDT m-11 y-2015 [mmc]: speed mode : HSSDR52/SDR25 [mmc]: clock : 50000000 Hz [mmc]: bus_width : 4 bit [mmc]: user capacity : 30528 MB [mmc]: ************SD/MMC 0 init OK!!!************ [mmc]: erase_grp_size : 0x1WrBlk*0x200=0x200 Byte [mmc]: secure_feature : 0x0 [mmc]: secure_removal_type : 0x0 [ 2.175]sunxi flash init ok [mmc]: Has init [ 2.207]---drivers/mmc/mmc.c 2733 mmc_init reading uboot.env ** Unable to read "uboot.env" from mmc0:1 ** Using default environment --------fastboot partitions-------- mbr not exist base bootcmd=run mmcbootcmd bootcmd set setargs_mmc key 0 recovery key high 12, low 10 fastboot key high 6, low 4 no misc partition is found to be run cmd=run mmcbootcmd update dtb dram start update dtb dram end serial is: 8400519008005c19014b get Pine64 model from DRAM size DRAM >512M Pine64 model: pine64-plus no battery exist sunxi_bmp_logo_display ** Bad device size - sunxi_flash 0 ** sunxi bmp info error : unable to open logo file bootlogo.bmp [ 2.412]inter uboot shell Hit any key to stop autoboot: 0 sunxi#