[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.202 (adam@adam-vb) (gcc version 7.1.1 20170707 (Linaro GCC 7.1-2017.08) ) #1 SMP Thu Nov 21 20:47:27 EST 2019 [ 0.000000] Boot CPU: AArch64 Processor [410fd034] [ 0.000000] earlycon: Early serial console at MMIO32 0xff1a0000 (options '') [ 0.000000] bootconsole [uart0] enabled [ 0.000000] Reserved memory: failed to reserve memory for node 'drm-logo@00000000': base 0x0000000000000000, size 0 MiB [ 0.000000] On node 0 totalpages: 1015296 [ 0.000000] DMA zone: 15864 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 1015296 pages, LIFO batch:31 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] PERCPU: Embedded 20 pages/cpu @ffffffc0f7ed6000 s42024 r8192 d31704 u81920 [ 0.000000] pcpu-alloc: s42024 r8192 d31704 u81920 alloc=20*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: enabling workaround for ARM erratum 845719 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 999432 [ 0.000000] Kernel command line: console=ttyS2,1500000n8 rw root=/dev/mmcblk1p2 rootwait rootfstype=ext4 panic=10 init=/sbin/init coherent_pool=1M ethaddr=06:38:36:17:fd:ea eth1addr=06:38:36:17:fd:0a serial=f9796353be11fe3 cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1 zswap.enabled=1 video=HDMI-A-1:1920x1080@60 video=eDP-1:1920x1080@60 quiet loglevel=3 vga=current earlycon=uart8250,mmio32,0xff1a0000 swiotlb=1 usbcore.autosuspend=-1 net.ifnames=0 [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] software IO TLB: mapped [mem 0xf7e8e000-0xf7ece000] (0MB) [ 0.000000] Memory: 3962272K/4061184K available (15422K kernel code, 1976K rwdata, 6140K rodata, 1216K init, 762K bss, 98912K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000 ( 246 GB) .init : 0xffffff80095a0000 - 0xffffff80096d0000 ( 1216 KB) .text : 0xffffff8008080000 - 0xffffff8008f90000 ( 15424 KB) .rodata : 0xffffff8008f90000 - 0xffffff80095a0000 ( 6208 KB) .data : 0xffffff80096d0000 - 0xffffff80098be008 ( 1977 KB) vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum) 0xffffffbdc0008000 - 0xffffffbdc3e00000 ( 61 MB actual) fixed : 0xffffffbffe7fb000 - 0xffffffbffec00000 ( 4116 KB) PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000 ( 16 MB) memory : 0xffffffc000200000 - 0xffffffc0f8000000 ( 3966 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=6. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=6 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] ITS: /interrupt-controller@fee00000/interrupt-controller@fee20000 [ 0.000000] ITS: allocated 65536 Devices @f3080000 (psz 64K, shr 0) [ 0.000000] ITS: using cache flushing for cmd queue [ 0.000000] GIC: using LPI property table @0x00000000f3010000 [ 0.000000] ITS: Allocated 1792 chunks for LPIs [ 0.000000] CPU0: found redistributor 0 region 0:0x00000000fef00000 [ 0.000000] CPU0: using LPI pending table @0x00000000f3020000 [ 0.000000] GIC: using cache flushing for LPI property table [ 0.000000] GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] } [ 0.000000] GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] } [ 0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop0_frac as parent of dclk_vop0, rate changes may not work [ 0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop1_frac as parent of dclk_vop1, rate changes may not work [ 0.000000] rockchip_cpuclk_pre_rate_change: limiting alt-divider 33 to 31 [ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.001465] Console: colour dummy device 80x25 [ 0.001491] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=24000) [ 0.001504] pid_max: default: 32768 minimum: 301 [ 0.001649] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.001661] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.002463] Initializing cgroup subsys memory [ 0.002493] Initializing cgroup subsys devices [ 0.002508] Initializing cgroup subsys freezer [ 0.002525] Initializing cgroup subsys net_cls [ 0.002538] Initializing cgroup subsys net_prio [ 0.002566] ftrace: allocating 55826 entries in 219 pages [ 0.156294] sched-energy: Sched-energy-costs installed from DT [ 0.156314] CPU0: update cpu_capacity 401 [ 0.156369] ASID allocator initialised with 32768 entries [ 0.160357] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created [ 0.160915] Platform MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created [ 0.162317] Detected VIPT I-cache on CPU1 [ 0.162350] CPU1: found redistributor 1 region 0:0x00000000fef20000 [ 0.162381] CPU1: using LPI pending table @0x00000000f32e0000 [ 0.162423] CPU1: update cpu_capacity 401 [ 0.162427] CPU1: Booted secondary processor [410fd034] [ 0.162978] Detected VIPT I-cache on CPU2 [ 0.162999] CPU2: found redistributor 2 region 0:0x00000000fef40000 [ 0.163026] CPU2: using LPI pending table @0x00000000f3310000 [ 0.163053] CPU2: update cpu_capacity 401 [ 0.163057] CPU2: Booted secondary processor [410fd034] [ 0.163606] Detected VIPT I-cache on CPU3 [ 0.163627] CPU3: found redistributor 3 region 0:0x00000000fef60000 [ 0.163654] CPU3: using LPI pending table @0x00000000f3360000 [ 0.163680] CPU3: update cpu_capacity 401 [ 0.163684] CPU3: Booted secondary processor [410fd034] [ 0.164220] Detected PIPT I-cache on CPU4 [ 0.164249] CPU4: found redistributor 100 region 0:0x00000000fef80000 [ 0.164289] CPU4: using LPI pending table @0x00000000f33a0000 [ 0.164328] CPU4: update cpu_capacity 1024 [ 0.164331] CPU4: Booted secondary processor [410fd082] [ 0.164890] Detected PIPT I-cache on CPU5 [ 0.164910] CPU5: found redistributor 101 region 0:0x00000000fefa0000 [ 0.164946] CPU5: using LPI pending table @0x00000000f33d0000 [ 0.164972] CPU5: update cpu_capacity 1024 [ 0.164976] CPU5: Booted secondary processor [410fd082] [ 0.165064] Brought up 6 CPUs [ 0.165146] SMP: Total of 6 processors activated. [ 0.165155] CPU features: detected feature: GIC system register CPU interface [ 0.165165] CPU features: detected feature: 32-bit EL0 Support [ 0.165177] CPU: All CPU(s) started at EL2 [ 0.165223] alternatives: patching kernel code [ 0.166662] devtmpfs: initialized [ 0.185057] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns [ 0.185078] futex hash table entries: 2048 (order: 5, 131072 bytes) [ 0.185577] xor: measuring software checksum speed [ 0.195571] 8regs : 2860.000 MB/sec [ 0.205627] 8regs_prefetch: 2556.000 MB/sec [ 0.215682] 32regs : 3204.000 MB/sec [ 0.225737] 32regs_prefetch: 2848.000 MB/sec [ 0.225743] xor: using function: 32regs (3204.000 MB/sec) [ 0.225762] pinctrl core: initialized pinctrl subsystem [ 0.225993] regulator-dummy: no parameters [ 0.227811] NET: Registered protocol family 16 [ 0.232475] cpuidle: using governor ladder [ 0.236497] cpuidle: using governor menu [ 0.237281] vdso: 2 pages (1 code @ ffffff8008f96000, 1 data @ ffffff80096d4000) [ 0.237309] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.237848] DMA: preallocated 1024 KiB pool for atomic allocations [ 0.253298] gpiochip_add_data: registered GPIOs 0 to 31 on device: gpio0 [ 0.253377] gpiochip_add_data: registered GPIOs 32 to 63 on device: gpio1 [ 0.253447] gpiochip_add_data: registered GPIOs 64 to 95 on device: gpio2 [ 0.253520] gpiochip_add_data: registered GPIOs 96 to 127 on device: gpio3 [ 0.253594] gpiochip_add_data: registered GPIOs 128 to 159 on device: gpio4 [ 0.260740] console [pstore-1] enabled [ 0.260748] pstore: Registered ramoops as persistent store backend [ 0.260757] ramoops: attached 0xf0000@0x110000, ecc: 0/0 [ 0.313366] raid6: int64x1 gen() 453 MB/s [ 0.330335] raid6: int64x1 xor() 375 MB/s [ 0.347492] raid6: int64x2 gen() 781 MB/s [ 0.364524] raid6: int64x2 xor() 583 MB/s [ 0.381627] raid6: int64x4 gen() 1109 MB/s [ 0.398727] raid6: int64x4 xor() 671 MB/s [ 0.415803] raid6: int64x8 gen() 855 MB/s [ 0.432934] raid6: int64x8 xor() 632 MB/s [ 0.450031] raid6: neonx1 gen() 910 MB/s [ 0.467078] raid6: neonx1 xor() 642 MB/s [ 0.484195] raid6: neonx2 gen() 1558 MB/s [ 0.501289] raid6: neonx2 xor() 955 MB/s [ 0.518366] raid6: neonx4 gen() 2007 MB/s [ 0.535480] raid6: neonx4 xor() 1160 MB/s [ 0.552559] raid6: neonx8 gen() 1695 MB/s [ 0.569649] raid6: neonx8 xor() 1246 MB/s [ 0.569657] raid6: using algorithm neonx4 gen() 2007 MB/s [ 0.569664] raid6: .... xor() 1160 MB/s, rmw enabled [ 0.569672] raid6: using intx1 recovery algorithm [ 0.570230] ACPI: Interpreter disabled. [ 0.570781] of_get_named_gpiod_flags: parsed 'rockchip,power-ctrl' property of node '/rockchip-suspend[0]' - status (0) [ 0.570824] of_get_named_gpiod_flags: parsed 'rockchip,power-ctrl' property of node '/rockchip-suspend[1]' - status (0) [ 0.571124] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/vcc-sys[0]' [ 0.571149] vcc_sys: 5000 mV [ 0.571328] reg-fixed-voltage vcc-sys: vcc_sys supplying 5000000uV [ 0.571383] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/vcc3v3-sys[0]' [ 0.571403] reg-fixed-voltage vcc3v3-sys: Looking up vin-supply from device tree [ 0.571453] vcc3v3_sys: supplied by vcc_sys [ 0.571497] vcc3v3_sys: 3300 mV [ 0.571649] reg-fixed-voltage vcc3v3-sys: vcc3v3_sys supplying 3300000uV [ 0.571811] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/vcc5v0-host-regulator[0]' [ 0.571868] of_get_named_gpiod_flags: parsed 'gpios' property of node '/vcc5v0-host-regulator[0]' - status (0) [ 0.571906] of_get_named_gpiod_flags: parsed 'gpios' property of node '/vcc5v0-host-regulator[1]' - status (0) [ 0.571967] vcc5v0_host: no parameters [ 0.572132] reg-fixed-voltage vcc5v0-host-regulator: vcc5v0_host supplying 0uV [ 0.572264] of_get_named_gpiod_flags: parsed 'gpio' property of node '/vcc-lcd-en-regulator[0]' - status (0) [ 0.572304] reg-fixed-voltage vcc-lcd-en-regulator: Looking up vin-supply from device tree [ 0.572341] vcc_lcd_en: supplied by vcc3v3_sys [ 0.572385] vcc_lcd_en: at 3300 mV [ 0.572539] reg-fixed-voltage vcc-lcd-en-regulator: vcc_lcd_en supplying 0uV [ 0.572603] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/vcc1v8-sdio[0]' [ 0.572623] reg-fixed-voltage vcc1v8-sdio: Looking up vin-supply from device tree [ 0.572640] vcc1v8_sdio: unable to resolve supply [ 0.572649] vcc1v8_sdio: 1800 mV [ 0.572773] reg-fixed-voltage vcc1v8-sdio: Looking up vin-supply from device tree [ 0.572791] vcc1v8_sdio: regulator get failed, ret=-517 [ 0.572803] reg-fixed-voltage vcc1v8-sdio: Looking up vin-supply from device tree [ 0.572818] vcc1v8_sdio: unable to resolve supply [ 0.572829] reg-fixed-voltage vcc1v8-sdio: vcc1v8_sdio supplying 1800000uV [ 0.572955] of_get_named_gpiod_flags: parsed 'gpio' property of node '/vcc3v0-sdio[0]' - status (0) [ 0.572999] reg-fixed-voltage vcc3v0-sdio: Looking up vin-supply from device tree [ 0.573047] vcc3v0_sdio: supplied by vcc3v3_sys [ 0.573095] vcc3v0_sdio: 3000 mV [ 0.573254] reg-fixed-voltage vcc1v8-sdio: Looking up vin-supply from device tree [ 0.573272] vcc1v8_sdio: unable to resolve supply [ 0.573284] reg-fixed-voltage vcc3v0-sdio: vcc3v0_sdio supplying 3000000uV [ 0.573910] iommu: Adding device ff650000.vpu_service to group 0 [ 0.574000] iommu: Adding device ff660000.rkvdec to group 1 [ 0.574126] iommu: Adding device ff8f0000.vop to group 2 [ 0.574225] iommu: Adding device ff900000.vop to group 3 [ 0.574736] rk_iommu ff650800.iommu: can't get sclk [ 0.575008] rk_iommu ff660480.iommu: can't get sclk [ 0.575237] rk_iommu ff8f3f00.iommu: can't get sclk [ 0.575412] rk_iommu ff903f00.iommu: can't get sclk [ 0.575777] SCSI subsystem initialized [ 0.575948] libata version 3.00 loaded. [ 0.576166] usbcore: registered new interface driver usbfs [ 0.576215] usbcore: registered new interface driver hub [ 0.576299] usbcore: registered new device driver usb [ 0.576417] media: Linux media interface: v0.10 [ 0.576455] Linux video capture interface: v2.00 [ 0.576586] pps_core: LinuxPPS API ver. 1 registered [ 0.576595] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.576618] PTP clock support registered [ 0.577910] Advanced Linux Sound Architecture Driver Initialized. [ 0.578445] Bluetooth: Core ver 2.21 [ 0.578476] NET: Registered protocol family 31 [ 0.578484] Bluetooth: HCI device and connection manager initialized [ 0.578498] Bluetooth: HCI socket layer initialized [ 0.578509] Bluetooth: L2CAP socket layer initialized [ 0.578545] Bluetooth: SCO socket layer initialized [ 0.579178] rockchip-cpuinfo cpuinfo: Serial : f9796353be11fe35 [ 0.580336] clocksource: Switched to clocksource arch_sys_counter [ 0.622808] FS-Cache: Loaded [ 0.623007] pnp: PnP ACPI: disabled [ 0.631568] thermal thermal_zone1: power_allocator: sustainable_power will be estimated [ 0.631841] NET: Registered protocol family 2 [ 0.632296] TCP established hash table entries: 32768 (order: 6, 262144 bytes) [ 0.632578] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes) [ 0.633413] TCP: Hash tables configured (established 32768 bind 32768) [ 0.633540] UDP hash table entries: 2048 (order: 5, 196608 bytes) [ 0.633707] UDP-Lite hash table entries: 2048 (order: 5, 196608 bytes) [ 0.634077] NET: Registered protocol family 1 [ 0.634430] RPC: Registered named UNIX socket transport module. [ 0.634440] RPC: Registered udp transport module. [ 0.634447] RPC: Registered tcp transport module. [ 0.634455] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.635112] PCI: CLS 0 bytes, default 64 [ 0.636263] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available [ 0.636376] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available [ 0.637833] kvm [1]: 8-bit VMID [ 0.637843] kvm [1]: Hyp mode initialized successfully [ 0.637971] kvm [1]: interrupt-controller@fff20000 IRQ10 [ 0.638162] kvm [1]: timer IRQ12 [ 0.641542] Initialise system trusted keyring [ 0.647713] zbud: loaded [ 0.649847] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.650640] NFS: Registering the id_resolver key type [ 0.650667] Key type id_resolver registered [ 0.650675] Key type id_legacy registered [ 0.650694] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.651419] fuse init (API version 7.23) [ 0.651803] SGI XFS with security attributes, no debug enabled [ 0.653505] aufs 4.4-20170911 [ 0.658249] NET: Registered protocol family 38 [ 0.658278] async_tx: api initialized (async) [ 0.658300] Key type asymmetric registered [ 0.658314] Asymmetric key parser 'x509' registered [ 0.658490] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 0.658507] io scheduler noop registered [ 0.658521] io scheduler deadline registered [ 0.658646] io scheduler cfq registered (default) [ 0.659707] phy phy-ff770000.syscon:usb2-phy@e460.0: Looking up phy-supply from device tree [ 0.660115] phy phy-ff770000.syscon:usb2-phy@e460.1: Looking up phy-supply from device tree [ 0.660130] phy phy-ff770000.syscon:usb2-phy@e460.1: Looking up phy-supply property in node /syscon@ff770000/usb2-phy@e460/otg-port failed [ 0.660216] phy phy-ff770000.syscon:usb2-phy@e460.1: Looking up vbus-supply from device tree [ 0.660228] phy phy-ff770000.syscon:usb2-phy@e460.1: Looking up vbus-supply property in node /syscon@ff770000/usb2-phy@e460/otg-port failed [ 0.660242] phy phy-ff770000.syscon:usb2-phy@e460.1: Failed to get VBUS supply regulator [ 0.661863] phy phy-ff770000.syscon:phy@f780.2: Looking up phy-supply from device tree [ 0.661877] phy phy-ff770000.syscon:phy@f780.2: Looking up phy-supply property in node /syscon@ff770000/phy@f780 failed [ 0.662718] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_tcpc0-supply from device tree [ 0.662733] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_tcpc0-supply property in node /power-management@ff310000/power-controller failed [ 0.663023] phy phy-ff800000.phy.3: Looking up phy-supply from device tree [ 0.663036] phy phy-ff800000.phy.3: Looking up phy-supply property in node /phy@ff800000/dp-port failed [ 0.663136] phy phy-ff800000.phy.4: Looking up phy-supply from device tree [ 0.663147] phy phy-ff800000.phy.4: Looking up phy-supply property in node /phy@ff800000/usb3-port failed [ 0.663252] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_tcpc1-supply from device tree [ 0.663264] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_tcpc1-supply property in node /power-management@ff310000/power-controller failed [ 0.664692] of_get_named_gpiod_flags: parsed 'gpios' property of node '/dc-charger[0]' - status (0) [ 0.665265] rockchip-iodomain ff320000.syscon:io-domains: Looking up pmu1830-supply from device tree [ 0.665436] rockchip-iodomain ff770000.syscon:io-domains: Looking up bt656-supply from device tree [ 0.665895] universal-charger usb-charger: GPIO lookup for consumer dc-det [ 0.665905] universal-charger usb-charger: using device tree for GPIO lookup [ 0.665916] of_get_named_gpiod_flags: can't parse 'dc-det-gpios' property of node '/usb-charger[0]' [ 0.665926] of_get_named_gpiod_flags: can't parse 'dc-det-gpio' property of node '/usb-charger[0]' [ 0.665936] universal-charger usb-charger: using lookup tables for GPIO lookup [ 0.665945] universal-charger usb-charger: lookup for GPIO dc-det failed [ 0.665955] universal-charger usb-charger: invalid dc det gpio! [ 0.665976] universal-charger usb-charger: init usb failed! [ 0.666510] Boot mode: coldboot [ 0.667531] pwm-backlight edp-backlight: GPIO lookup for consumer enable [ 0.667543] pwm-backlight edp-backlight: using device tree for GPIO lookup [ 0.667555] of_get_named_gpiod_flags: can't parse 'enable-gpios' property of node '/edp-backlight[0]' [ 0.667565] of_get_named_gpiod_flags: can't parse 'enable-gpio' property of node '/edp-backlight[0]' [ 0.667574] pwm-backlight edp-backlight: using lookup tables for GPIO lookup [ 0.667584] pwm-backlight edp-backlight: lookup for GPIO enable failed [ 0.667595] pwm-backlight edp-backlight: Looking up power-supply from device tree [ 0.667910] rk-vcodec ff650000.vpu_service: Looking up vcodec-supply from device tree [ 0.667923] rk-vcodec ff650000.vpu_service: Looking up vcodec-supply property in node /vpu_service@ff650000 failed [ 0.667939] rk-vcodec ff650000.vpu_service: no regulator for vcodec [ 0.668174] rk-vcodec ff650000.vpu_service: probe device [ 0.668435] rk-vcodec ff650000.vpu_service: drm allocator with mmu enabled [ 0.668988] rk-vcodec ff650000.vpu_service: init success [ 0.669217] rk-vcodec ff660000.rkvdec: Looking up vcodec-supply from device tree [ 0.669230] rk-vcodec ff660000.rkvdec: Looking up vcodec-supply property in node /rkvdec@ff660000 failed [ 0.669247] rk-vcodec ff660000.rkvdec: no regulator for vcodec [ 0.669682] rk-vcodec ff660000.rkvdec: probe device [ 0.669876] rk-vcodec ff660000.rkvdec: drm allocator with mmu enabled [ 0.670254] rk-vcodec ff660000.rkvdec: could not find power_model node [ 0.670264] rk-vcodec ff660000.rkvdec: init success [ 0.672072] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 0.672086] dma-pl330 ff6d0000.dma-controller: DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12 [ 0.673585] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 0.673598] dma-pl330 ff6e0000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16 [ 0.673887] rockchip-system-monitor rockchip-system-monitor: system monitor probe [ 0.674297] pwm-regulator vdd-log: GPIO lookup for consumer enable [ 0.674307] pwm-regulator vdd-log: using device tree for GPIO lookup [ 0.674320] of_get_named_gpiod_flags: can't parse 'enable-gpios' property of node '/vdd-log[0]' [ 0.674359] of_get_named_gpiod_flags: can't parse 'enable-gpio' property of node '/vdd-log[0]' [ 0.674369] pwm-regulator vdd-log: using lookup tables for GPIO lookup [ 0.674380] pwm-regulator vdd-log: lookup for GPIO enable failed [ 0.674427] pwm-regulator vdd-log: Looking up pwm-supply from device tree [ 0.674520] pwm-regulator: supplied by vcc_sys [ 0.674573] vdd_log: 800 <--> 1400 mV at 896 mV [ 0.674780] reg-fixed-voltage vcc1v8-sdio: Looking up vin-supply from device tree [ 0.674802] vcc1v8_sdio: unable to resolve supply [ 0.675260] Serial: 8250/16550 driver, 5 ports, IRQ sharing disabled [ 0.675947] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 35, base_baud = 1500000) is a 16550A [ 0.676477] ff1a0000.serial: ttyS2 at MMIO 0xff1a0000 (irq = 36, base_baud = 1500000) is a 16550A [ 0.676517] console [ttyS2] enabled [ 0.676526] bootconsole [uart0] disabled [ 0.677648] [drm] Initialized drm 1.1.0 20060810 [ 0.678320] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_hdcp-supply from device tree [ 0.678352] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_hdcp-supply property in node /power-management@ff310000/power-controller failed [ 0.681767] [drm] Rockchip DRM driver version: v1.0.1 [ 0.682314] usbcore: registered new interface driver udl [ 0.683503] panel-simple edp-panel: Looking up power-supply from device tree [ 0.683529] panel-simple edp-panel: failed to get power regulator: -517 [ 0.684194] Unable to detect cache hierarchy for CPU 0 [ 0.684950] brd: module loaded [ 0.690130] loop: module loaded [ 0.690673] zram: Added device: zram0 [ 0.691038] lkdtm: No crash points registered, enable through debugfs [ 0.692252] rockchip-spi ff1d0000.spi: no high_speed pinctrl state [ 0.693195] CAN device driver interface [ 0.693209] sja1000 CAN netdevice driver [ 0.693276] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI [ 0.693284] e100: Copyright(c) 1999-2006 Intel Corporation [ 0.693377] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI [ 0.693385] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 0.693442] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.693449] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.693500] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.3.0-k [ 0.693507] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.693557] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver - version 4.2.1-k [ 0.693564] ixgbe: Copyright (c) 1999-2015 Intel Corporation. [ 0.694447] Atmel at76x USB Wireless LAN Driver 0.17 loading [ 0.694502] usbcore: registered new interface driver at76c50x-usb [ 0.694560] Broadcom 43xx driver loaded [ Features: PNL ] [ 0.694725] usbcore: registered new interface driver zd1211rw [ 0.694777] usbcore: registered new interface driver rtl8187 [ 0.694831] usbcore: registered new interface driver rtl8xxxu [ 0.694885] usbcore: registered new interface driver rndis_wlan [ 0.694942] usbcore: registered new interface driver usb8xxx [ 0.695126] usbcore: registered new interface driver rt2500usb [ 0.695175] usbcore: registered new interface driver rt73usb [ 0.695225] usbcore: registered new interface driver rt2800usb [ 0.695268] usbcore: registered new interface driver mt7601u [ 0.695433] usbcore: registered new interface driver ath6kl_usb [ 0.695478] usbcore: registered new interface driver ar5523 [ 0.695698] usbcore: registered new interface driver mwifiex_usb [ 0.695772] usbcore: registered new interface driver brcmfmac [ 0.695825] Rockchip WiFi SYS interface (V1.00) ... [ 0.695898] usbcore: registered new interface driver rtl8150 [ 0.695946] usbcore: registered new interface driver r8152 [ 0.695995] usbcore: registered new interface driver asix [ 0.696039] usbcore: registered new interface driver ax88179_178a [ 0.696084] usbcore: registered new interface driver cdc_ether [ 0.696129] usbcore: registered new interface driver rndis_host [ 0.696199] usbcore: registered new interface driver cdc_ncm [ 0.696244] usbcore: registered new interface driver cdc_mbim [ 0.697879] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_usb3-supply from device tree [ 0.697896] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_usb3-supply property in node /power-management@ff310000/power-controller failed [ 0.698047] rockchip-dwc3 usb0: failed to get drvdata dwc3 [ 0.702464] rockchip-dwc3 usb1: fail to get drvdata hcd [ 0.703733] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.703771] ehci-pci: EHCI PCI platform driver [ 0.703841] ehci-platform: EHCI generic platform driver [ 0.707366] ehci-platform fe3c0000.usb: EHCI Host Controller [ 0.707530] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 1 [ 0.707647] ehci-platform fe3c0000.usb: irq 29, io mem 0xfe3c0000 [ 0.713357] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00 [ 0.713525] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 0.713537] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.713547] usb usb1: Product: EHCI Host Controller [ 0.713557] usb usb1: Manufacturer: Linux 4.4.202 ehci_hcd [ 0.713566] usb usb1: SerialNumber: fe3c0000.usb [ 0.714036] hub 1-0:1.0: USB hub found [ 0.714067] hub 1-0:1.0: 1 port detected [ 0.714718] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.714743] ohci-platform: OHCI generic platform driver [ 0.715245] ohci-platform fe3e0000.usb: Generic Platform OHCI controller [ 0.715449] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 2 [ 0.715541] ohci-platform fe3e0000.usb: irq 30, io mem 0xfe3e0000 [ 0.770507] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 0.770519] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.770529] usb usb2: Product: Generic Platform OHCI controller [ 0.770538] usb usb2: Manufacturer: Linux 4.4.202 ohci_hcd [ 0.770547] usb usb2: SerialNumber: fe3e0000.usb [ 0.771003] hub 2-0:1.0: USB hub found [ 0.771036] hub 2-0:1.0: 1 port detected [ 0.772028] usbcore: registered new interface driver cdc_wdm [ 0.772084] usbcore: registered new interface driver uas [ 0.772171] usbcore: registered new interface driver usb-storage [ 0.772215] usbcore: registered new interface driver ums-alauda [ 0.772259] usbcore: registered new interface driver ums-cypress [ 0.772305] usbcore: registered new interface driver ums-datafab [ 0.772367] usbcore: registered new interface driver ums_eneub6250 [ 0.772417] usbcore: registered new interface driver ums-freecom [ 0.772462] usbcore: registered new interface driver ums-isd200 [ 0.772508] usbcore: registered new interface driver ums-jumpshot [ 0.772553] usbcore: registered new interface driver ums-karma [ 0.772598] usbcore: registered new interface driver ums-onetouch [ 0.772651] usbcore: registered new interface driver ums-realtek [ 0.772696] usbcore: registered new interface driver ums-sddr09 [ 0.772737] usbcore: registered new interface driver ums-sddr55 [ 0.772781] usbcore: registered new interface driver ums-usbat [ 0.772863] usbcore: registered new interface driver usbserial [ 0.772902] usbcore: registered new interface driver usbserial_generic [ 0.772933] usbserial: USB Serial support registered for generic [ 0.772976] usbcore: registered new interface driver cp210x [ 0.773004] usbserial: USB Serial support registered for cp210x [ 0.773063] usbcore: registered new interface driver ftdi_sio [ 0.773092] usbserial: USB Serial support registered for FTDI USB Serial Device [ 0.773181] usbcore: registered new interface driver keyspan [ 0.773210] usbserial: USB Serial support registered for Keyspan - (without firmware) [ 0.773239] usbserial: USB Serial support registered for Keyspan 1 port adapter [ 0.773267] usbserial: USB Serial support registered for Keyspan 2 port adapter [ 0.773294] usbserial: USB Serial support registered for Keyspan 4 port adapter [ 0.773352] usbcore: registered new interface driver option [ 0.773385] usbserial: USB Serial support registered for GSM modem (1-port) [ 0.773501] usbcore: registered new interface driver oti6858 [ 0.773529] usbserial: USB Serial support registered for oti6858 [ 0.773575] usbcore: registered new interface driver pl2303 [ 0.773604] usbserial: USB Serial support registered for pl2303 [ 0.773652] usbcore: registered new interface driver qcserial [ 0.773680] usbserial: USB Serial support registered for Qualcomm USB modem [ 0.773734] usbcore: registered new interface driver sierra [ 0.773763] usbserial: USB Serial support registered for Sierra USB modem [ 0.774998] usbcore: registered new interface driver iforce [ 0.775601] usbcore: registered new interface driver xpad [ 0.776014] usbcore: registered new interface driver usbtouchscreen [ 0.776317] sensor_register_slave:mma8452,id=17 [ 0.776349] sensor_register_slave:lis3dh,id=7 [ 0.776361] sensor_register_slave:mma7660,id=18 [ 0.776372] sensor_register_slave:lsm303d,id=22 [ 0.776384] sensor_register_slave:mpu6880_acc,id=24 [ 0.776396] sensor_register_slave:mpu6500_acc,id=25 [ 0.776407] sensor_register_slave:lsm330_acc,id=26 [ 0.776420] sensor_register_slave:akm8975,id=30 [ 0.776431] sensor_register_slave:akm8963,id=31 [ 0.776443] sensor_register_slave:l3g4200d,id=45 [ 0.776454] sensor_register_slave:l3g20d,id=46 [ 0.776466] sensor_register_slave:ewtsa,id=47 [ 0.776477] sensor_register_slave:lsm330_gyro,id=51 [ 0.776489] sensor_register_slave:cm3217,id=53 [ 0.776500] sensor_register_slave:cm3218,id=54 [ 0.777211] i2c /dev entries driver [ 0.778152] fan53555-regulator 0-0040: GPIO lookup for consumer vsel [ 0.778165] fan53555-regulator 0-0040: using device tree for GPIO lookup [ 0.778198] of_get_named_gpiod_flags: parsed 'vsel-gpios' property of node '/i2c@ff3c0000/syr827@40[0]' - status (0) [ 0.778595] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected! [ 0.778615] fan53555-regulator 0-0040: Looking up vin-supply from device tree [ 0.778667] fan53555-reg: supplied by vcc_sys [ 0.780098] vdd_cpu_b: 712 <--> 1400 mV at 1000 mV [ 0.780486] reg-fixed-voltage vcc1v8-sdio: Looking up vin-supply from device tree [ 0.780510] vcc1v8_sdio: unable to resolve supply [ 0.780745] fan53555-regulator 0-0041: GPIO lookup for consumer vsel [ 0.780755] fan53555-regulator 0-0041: using device tree for GPIO lookup [ 0.780784] of_get_named_gpiod_flags: parsed 'vsel-gpios' property of node '/i2c@ff3c0000/syr828@41[0]' - status (0) [ 0.781145] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected! [ 0.781160] fan53555-regulator 0-0041: Looking up vin-supply from device tree [ 0.781201] fan53555-reg: supplied by vcc_sys [ 0.782787] vdd_gpu: 712 <--> 1200 mV at 1000 mV [ 0.783138] reg-fixed-voltage vcc1v8-sdio: Looking up vin-supply from device tree [ 0.783160] vcc1v8_sdio: unable to resolve supply [ 0.783772] rk808 0-001b: Pmic Chip id: 0x0 [ 0.786957] rk808 0-001b: GPIO lookup for consumer dvs [ 0.786967] rk808 0-001b: using device tree for GPIO lookup [ 0.786980] of_get_named_gpiod_flags: can't parse 'dvs-gpios' property of node '/i2c@ff3c0000/pmic@1b[0]' [ 0.786991] of_get_named_gpiod_flags: can't parse 'dvs-gpio' property of node '/i2c@ff3c0000/pmic@1b[0]' [ 0.787001] rk808 0-001b: using lookup tables for GPIO lookup [ 0.787011] rk808 0-001b: lookup for GPIO dvs failed [ 0.787021] rk808-regulator rk808-regulator: there is no dvs0 gpio [ 0.787030] rk808 0-001b: GPIO lookup for consumer dvs [ 0.787039] rk808 0-001b: using device tree for GPIO lookup [ 0.787049] of_get_named_gpiod_flags: can't parse 'dvs-gpios' property of node '/i2c@ff3c0000/pmic@1b[1]' [ 0.787059] of_get_named_gpiod_flags: can't parse 'dvs-gpio' property of node '/i2c@ff3c0000/pmic@1b[1]' [ 0.787068] rk808 0-001b: using lookup tables for GPIO lookup [ 0.787076] rk808 0-001b: lookup for GPIO dvs failed [ 0.787086] rk808-regulator rk808-regulator: there is no dvs1 gpio [ 0.787134] rk808 0-001b: Looking up vcc1-supply from device tree [ 0.787194] DCDC_REG1: supplied by vcc_sys [ 0.787668] vdd_center: 750 <--> 1350 mV at 900 mV [ 0.787880] reg-fixed-voltage vcc1v8-sdio: Looking up vin-supply from device tree [ 0.787901] vcc1v8_sdio: unable to resolve supply [ 0.787946] rk808 0-001b: Looking up vcc2-supply from device tree [ 0.787985] DCDC_REG2: supplied by vcc_sys [ 0.788303] vdd_cpu_l: 750 <--> 1250 mV at 900 mV [ 0.788529] reg-fixed-voltage vcc1v8-sdio: Looking up vin-supply from device tree [ 0.788550] vcc1v8_sdio: unable to resolve supply [ 0.788591] rk808 0-001b: Looking up vcc3-supply from device tree [ 0.788630] DCDC_REG3: supplied by vcc_sys [ 0.788666] vcc_ddr: at 5000 mV [ 0.788850] reg-fixed-voltage vcc1v8-sdio: Looking up vin-supply from device tree [ 0.788871] vcc1v8_sdio: unable to resolve supply [ 0.788918] rk808 0-001b: Looking up vcc4-supply from device tree [ 0.788955] DCDC_REG4: supplied by vcc_sys [ 0.789145] vcc_1v8: 1800 mV [ 0.789370] reg-fixed-voltage vcc1v8-sdio: Looking up vin-supply from device tree [ 0.789392] vcc1v8_sdio: supplied by vcc_1v8 [ 0.789470] rk808 0-001b: Looking up vcc6-supply from device tree [ 0.789510] LDO_REG1: supplied by vcc_sys [ 0.790369] vcc1v8_dvp: 1800 mV [ 0.790610] rk808 0-001b: Looking up vcc6-supply from device tree [ 0.790650] LDO_REG2: supplied by vcc_sys [ 0.790834] LDO_REG2: at 1800 mV [ 0.791077] rk808 0-001b: Looking up vcc7-supply from device tree [ 0.791116] LDO_REG3: supplied by vcc_sys [ 0.791826] vcc1v8_pmu: 1800 mV [ 0.792078] rk808 0-001b: Looking up vcc9-supply from device tree [ 0.792116] LDO_REG4: supplied by vcc_sys [ 0.792300] vcc_sd: Bringing 3300000uV into 3000000-3000000uV [ 0.792436] vcc_sd: ramp_delay not set [ 0.792974] vcc_sd: 1800 <--> 3000 mV at 3000 mV [ 0.793224] rk808 0-001b: Looking up vcc9-supply from device tree [ 0.793263] LDO_REG5: supplied by vcc_sys [ 0.793463] vcca3v0_codec: Bringing 1800000uV into 3000000-3000000uV [ 0.793596] vcca3v0_codec: ramp_delay not set [ 0.794250] vcca3v0_codec: 3000 mV [ 0.794518] rk808 0-001b: Looking up vcc10-supply from device tree [ 0.794557] LDO_REG6: supplied by vcc_sys [ 0.795267] vcc_1v5: 1500 mV [ 0.795538] rk808 0-001b: Looking up vcc7-supply from device tree [ 0.795576] LDO_REG7: supplied by vcc_sys [ 0.796287] vcca1v8_codec: 1800 mV [ 0.796567] rk808 0-001b: Looking up vcc11-supply from device tree [ 0.796607] LDO_REG8: supplied by vcc_sys [ 0.797317] vcc_3v0: 3000 mV [ 0.797596] rk808 0-001b: Looking up vcc8-supply from device tree [ 0.797636] SWITCH_REG1: supplied by vcc3v3_sys [ 0.797671] vcc3v3_s3: at 3300 mV [ 0.797912] rk808 0-001b: Looking up vcc12-supply from device tree [ 0.797953] SWITCH_REG2: supplied by vcc_lcd_en [ 0.898399] vcc3v3_s0: at 3300 mV [ 0.902395] rk808-rtc rk808-rtc: rtc core: registered rk808-rtc as rtc0 [ 0.902898] rk3x-i2c ff3c0000.i2c: Initialized RK3xxx I2C bus at ffffff8009bcc000 [ 0.903968] rk3x-i2c ff110000.i2c: Initialized RK3xxx I2C bus at ffffff8009bce000 [ 0.905246] fusb302 4-0022: GPIO lookup for consumer int-n [ 0.905260] fusb302 4-0022: using device tree for GPIO lookup [ 0.905304] of_get_named_gpiod_flags: parsed 'int-n-gpios' property of node '/i2c@ff3d0000/fusb30x@22[0]' - status (0) [ 0.905362] fusb302 4-0022: GPIO lookup for consumer vbus-5v [ 0.905375] fusb302 4-0022: using device tree for GPIO lookup [ 0.905411] of_get_named_gpiod_flags: parsed 'vbus-5v-gpios' property of node '/i2c@ff3d0000/fusb30x@22[0]' - status (0) [ 0.905443] fusb302 4-0022: GPIO lookup for consumer vbus-other [ 0.905455] fusb302 4-0022: using device tree for GPIO lookup [ 0.905469] of_get_named_gpiod_flags: can't parse 'vbus-other-gpios' property of node '/i2c@ff3d0000/fusb30x@22[0]' [ 0.905482] of_get_named_gpiod_flags: can't parse 'vbus-other-gpio' property of node '/i2c@ff3d0000/fusb30x@22[0]' [ 0.905494] fusb302 4-0022: using lookup tables for GPIO lookup [ 0.905507] fusb302 4-0022: lookup for GPIO vbus-other failed [ 0.905519] fusb302 4-0022: GPIO lookup for consumer discharge [ 0.905530] fusb302 4-0022: using device tree for GPIO lookup [ 0.905543] of_get_named_gpiod_flags: can't parse 'discharge-gpios' property of node '/i2c@ff3d0000/fusb30x@22[0]' [ 0.905556] of_get_named_gpiod_flags: can't parse 'discharge-gpio' property of node '/i2c@ff3d0000/fusb30x@22[0]' [ 0.905567] fusb302 4-0022: using lookup tables for GPIO lookup [ 0.905579] fusb302 4-0022: lookup for GPIO discharge failed [ 0.915191] fusb302 4-0022: port 0 probe success with role ROLE_MODE_DRP, try_role ROLE_MODE_NONE [ 0.915436] input: Typec_Headphone as /devices/platform/ff3d0000.i2c/i2c-4/4-0022/input/input0 [ 0.948461] thermal thermal_zone2: power_allocator: sustainable_power will be estimated [ 0.948756] cw201x 4-0062: cw2015/cw2013 driver v1.2 probe sucess [ 0.948821] rk3x-i2c ff3d0000.i2c: Initialized RK3xxx I2C bus at ffffff8009bd0000 [ 0.950616] IR NEC protocol handler initialized [ 0.950635] IR RC5(x/sz) protocol handler initialized [ 0.950651] IR RC6 protocol handler initialized [ 0.950667] IR JVC protocol handler initialized [ 0.950684] IR Sony protocol handler initialized [ 0.950700] IR SANYO protocol handler initialized [ 0.950716] IR Sharp protocol handler initialized [ 0.950732] IR MCE Keyboard/mouse protocol handler initialized [ 0.950748] IR XMP protocol handler initialized [ 0.952057] usbcore: registered new interface driver uvcvideo [ 0.952067] USB Video Class driver (1.1.1) [ 0.953734] rk_tsadcv2_temp_to_code: Invalid conversion table: code=1023, temperature=2147483647 [ 0.953969] rockchip-thermal ff260000.tsadc: tsadc is probed successfully! [ 0.954907] dw_wdt ff848000.watchdog: Should better to setup a 'resets' property in dt, that must been named with reset [ 0.955259] md: raid0 personality registered for level 0 [ 0.955275] md: raid1 personality registered for level 1 [ 0.955289] md: raid10 personality registered for level 10 [ 0.955588] md: raid6 personality registered for level 6 [ 0.955600] md: raid5 personality registered for level 5 [ 0.955609] md: raid4 personality registered for level 4 [ 0.956012] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com [ 0.956030] device-mapper: raid: Loading target version 1.7.0 [ 0.956046] Bluetooth: Virtual HCI driver ver 1.5 [ 0.956190] Bluetooth: HCI UART driver ver 2.3 [ 0.956203] Bluetooth: HCI UART protocol H4 registered [ 0.956213] Bluetooth: HCI UART protocol ATH3K registered [ 0.956317] usbcore: registered new interface driver bfusb [ 0.956420] usbcore: registered new interface driver btusb [ 0.956435] rtk_btusb: RTKBT_RELEASE_NAME: 20180702_BT_ANDROID_8.1 [ 0.956444] rtk_btusb: Realtek Bluetooth USB driver module init, version 4.1.5 [ 0.956452] rtk_btusb: Register usb char device interface for BT driver [ 0.956738] usbcore: registered new interface driver rtk_btusb [ 0.966477] ISDN subsystem Rev: 1.1.2.3/1.1.2.2/none/none/1.1.2.2 [ 0.966526] HiSax: Linux Driver for passive ISDN cards [ 0.966535] HiSax: Version 3.5 (kernel) [ 0.966544] HiSax: Layer1 Revision 2.46.2.5 [ 0.966553] HiSax: Layer2 Revision 2.30.2.4 [ 0.966562] HiSax: TeiMgr Revision 2.20.2.3 [ 0.966570] HiSax: Layer3 Revision 2.22.2.3 [ 0.966579] HiSax: LinkLayer Revision 2.59.2.4 [ 0.966608] HiSax: Total 1 card defined [ 0.966631] HiSax: Card 1 Protocol EDSS1 Id=HiSax (0) [ 0.966641] HiSax: W6692 driver Rev. 1.18.2.4 [ 0.966653] W6692: No PCI card found [ 0.966672] HiSax: Card Winbond 6692 not installed ! [ 0.966855] hisax_st5481: ST5481 USB ISDN driver $Revision: 2.4.2.3 $ [ 0.966977] usbcore: registered new interface driver st5481_usb [ 0.966999] HFC-S USB: driver module revision 2.3.2.24 date 2007/10/14 loaded, (debug=0) [ 0.967064] usbcore: registered new interface driver hfc_usb [ 0.967080] HFC-4S/8S: Layer 1 driver module for HFC-4S/8S isdn chips, Revision: 1.10 [ 0.967089] HFC-4S/8S: (C) 2003 Cornelius Consult, www.cornelius-consult.de [ 0.967149] HFC-4S/8S: found 0 cards [ 0.967163] hisax_isac: ISAC-S/ISAC-SX ISDN driver v0.1.0 [ 0.967179] hisax_fcpcipnp: Fritz!Card PCI/PCIv2/PnP ISDN driver v0.0.1 [ 0.968291] cpu cpu0: leakage=20 [ 0.968358] cpu cpu0: Looking up cpu-supply from device tree [ 0.970018] cpu cpu4: leakage=32 [ 0.970058] cpu cpu4: Looking up cpu-supply from device tree [ 0.971173] cpu cpu0: Looking up cpu-supply from device tree [ 0.971627] cpu cpu0: Looking up cpu-supply from device tree [ 0.972496] cpu cpu0: avs=0 [ 0.972643] cpu cpu0: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 [ 0.975172] cpu cpu0: failed to find power_model node [ 0.975525] cpu cpu4: Looking up cpu-supply from device tree [ 0.976120] cpu cpu4: avs=0 [ 0.976206] cpu cpu4: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 [ 0.977823] cpu cpu4: failed to find power_model node [ 0.979390] sdhci: Secure Digital Host Controller Interface driver [ 0.979397] sdhci: Copyright(c) Pierre Ossman [ 0.979405] Synopsys Designware Multimedia Card Interface Driver [ 0.980153] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode. [ 0.980187] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller. [ 0.980199] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a [ 0.980255] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 24,32 bit host data width,256 deep fifo [ 0.980279] dwmmc_rockchip fe310000.dwmmc: Looking up vmmc-supply from device tree [ 0.980419] dwmmc_rockchip fe310000.dwmmc: Looking up vqmmc-supply from device tree [ 0.980490] dwmmc_rockchip fe310000.dwmmc: GPIO lookup for consumer wp [ 0.980497] dwmmc_rockchip fe310000.dwmmc: using device tree for GPIO lookup [ 0.980506] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/dwmmc@fe310000[0]' [ 0.980514] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/dwmmc@fe310000[0]' [ 0.980522] dwmmc_rockchip fe310000.dwmmc: using lookup tables for GPIO lookup [ 0.980530] dwmmc_rockchip fe310000.dwmmc: lookup for GPIO wp failed [ 0.980643] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_sdioaudio-supply from device tree [ 0.980653] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_sdioaudio-supply property in node /power-management@ff310000/power-controller failed [ 0.981376] dwmmc_rockchip fe320000.dwmmc: IDMAC supports 32-bit address mode. [ 0.981404] dwmmc_rockchip fe320000.dwmmc: Using internal DMA controller. [ 0.981414] dwmmc_rockchip fe320000.dwmmc: Version ID is 270a [ 0.981458] dwmmc_rockchip fe320000.dwmmc: DW MMC controller at irq 25,32 bit host data width,256 deep fifo [ 0.981475] dwmmc_rockchip fe320000.dwmmc: Looking up vmmc-supply from device tree [ 0.981570] dwmmc_rockchip fe320000.dwmmc: Looking up vqmmc-supply from device tree [ 0.981635] dwmmc_rockchip fe320000.dwmmc: GPIO lookup for consumer cd [ 0.981643] dwmmc_rockchip fe320000.dwmmc: using device tree for GPIO lookup [ 0.981651] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/dwmmc@fe320000[0]' [ 0.981659] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/dwmmc@fe320000[0]' [ 0.981666] dwmmc_rockchip fe320000.dwmmc: using lookup tables for GPIO lookup [ 0.981674] dwmmc_rockchip fe320000.dwmmc: lookup for GPIO cd failed [ 0.981682] dwmmc_rockchip fe320000.dwmmc: GPIO lookup for consumer wp [ 0.981689] dwmmc_rockchip fe320000.dwmmc: using device tree for GPIO lookup [ 0.981696] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/dwmmc@fe320000[0]' [ 0.981703] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/dwmmc@fe320000[0]' [ 0.981710] dwmmc_rockchip fe320000.dwmmc: using lookup tables for GPIO lookup [ 0.981717] dwmmc_rockchip fe320000.dwmmc: lookup for GPIO wp failed [ 0.994492] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) [ 1.007163] dwmmc_rockchip fe320000.dwmmc: 1 slots initialized [ 1.007883] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.008947] sdhci-arasan fe330000.sdhci: GPIO lookup for consumer wp [ 1.008965] sdhci-arasan fe330000.sdhci: using device tree for GPIO lookup [ 1.008985] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/sdhci@fe330000[0]' [ 1.009003] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/sdhci@fe330000[0]' [ 1.009019] sdhci-arasan fe330000.sdhci: using lookup tables for GPIO lookup [ 1.009037] sdhci-arasan fe330000.sdhci: lookup for GPIO wp failed [ 1.010198] sdhci-arasan fe330000.sdhci: Looking up vmmc-supply from device tree [ 1.010221] sdhci-arasan fe330000.sdhci: Looking up vmmc-supply property in node /sdhci@fe330000 failed [ 1.010275] sdhci-arasan fe330000.sdhci: Looking up vqmmc-supply from device tree [ 1.010295] sdhci-arasan fe330000.sdhci: Looking up vqmmc-supply property in node /sdhci@fe330000 failed [ 1.010348] sdhci-arasan fe330000.sdhci: No vmmc regulator found [ 1.010364] sdhci-arasan fe330000.sdhci: No vqmmc regulator found [ 1.041182] mmc1: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using ADMA [ 1.042700] of_get_named_gpiod_flags: parsed 'gpios' property of node '/switches/hpout-en[0]' - status (0) [ 1.043049] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/green-led[0]' - status (0) [ 1.043297] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/red-led[0]' - status (0) [ 1.043931] ledtrig-cpu: registered to indicate activity on CPUs [ 1.044115] hidraw: raw HID events driver (C) Jiri Kosina [ 1.051461] usbcore: registered new interface driver usbhid [ 1.051482] usbhid: USB HID core driver [ 1.055816] usbcore: registered new interface driver snd-usb-audio [ 1.057438] of_get_named_gpiod_flags: parsed 'spk-con-gpio' property of node '/i2c@ff110000/es8316@11[0]' - status (0) [ 1.057537] of_get_named_gpiod_flags: parsed 'hp-det-gpio' property of node '/i2c@ff110000/es8316@11[0]' - status (0) [ 1.069265] u32 classifier [ 1.069313] Netfilter messages via NETLINK v0.30. [ 1.069477] ip_set: protocol 6 [ 1.069868] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1.069965] Initializing XFRM netlink socket [ 1.071084] NET: Registered protocol family 10 [ 1.073039] NET: Registered protocol family 17 [ 1.073117] NET: Registered protocol family 15 [ 1.073220] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 1.073296] Bridge firewalling registered [ 1.073319] can: controller area network core (rev 20120528 abi 9) [ 1.073788] NET: Registered protocol family 29 [ 1.073821] can: raw protocol (rev 20120528) [ 1.073848] can: broadcast manager protocol (rev 20120528 t) [ 1.073883] can: netlink gateway (rev 20130117) max_hops=1 [ 1.075101] Bluetooth: RFCOMM socket layer initialized [ 1.075212] Bluetooth: RFCOMM ver 1.11 [ 1.075263] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 1.075296] Bluetooth: HIDP socket layer initialized [ 1.075480] 8021q: 802.1Q VLAN Support v1.8 [ 1.075547] lib80211: common routines for IEEE802.11 drivers [ 1.075566] lib80211_crypt: registered algorithm 'NULL' [ 1.075594] [WLAN_RFKILL]: Enter rfkill_wlan_init [ 1.076439] [WLAN_RFKILL]: Enter rfkill_wlan_probe [ 1.076559] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6256 [ 1.076579] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control. [ 1.076597] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio. [ 1.076623] of_get_named_gpiod_flags: can't parse 'WIFI,poweren_gpio' property of node '/wireless-wlan[0]' [ 1.076647] of_get_named_gpiod_flags: can't parse 'WIFI,vbat_gpio' property of node '/wireless-wlan[0]' [ 1.076671] of_get_named_gpiod_flags: can't parse 'WIFI,reset_gpio' property of node '/wireless-wlan[0]' [ 1.076772] of_get_named_gpiod_flags: parsed 'WIFI,host_wake_irq' property of node '/wireless-wlan[0]' - status (0) [ 1.076793] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,host_wake_irq = 3, flags = 0. [ 1.076820] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found ! [ 1.076844] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio [ 1.076867] [WLAN_RFKILL]: Exit rfkill_wlan_probe [ 1.077003] [BT_RFKILL]: Enter rfkill_rk_init [ 1.078023] [BT_RFKILL]: Enter rfkill_rk_probe [ 1.078110] of_get_named_gpiod_flags: parsed 'uart_rts_gpios' property of node '/wireless-bluetooth[0]' - status (0) [ 1.078131] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 83. [ 1.078161] of_get_named_gpiod_flags: can't parse 'BT,power_gpio' property of node '/wireless-bluetooth[0]' [ 1.078230] of_get_named_gpiod_flags: parsed 'BT,reset_gpio' property of node '/wireless-bluetooth[0]' - status (0) [ 1.078250] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 9. [ 1.078318] of_get_named_gpiod_flags: parsed 'BT,wake_gpio' property of node '/wireless-bluetooth[0]' - status (0) [ 1.078373] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 91. [ 1.078442] of_get_named_gpiod_flags: parsed 'BT,wake_host_irq' property of node '/wireless-bluetooth[0]' - status (0) [ 1.078462] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 4. [ 1.078509] [RK808]: clkout2_prepare [ 1.080329] [BT_RFKILL]: init gpio [ 1.080528] [BT_RFKILL]: Request irq for bt wakeup host [ 1.080653] [BT_RFKILL]: ** disable irq [ 1.080679] [BT_RFKILL]: setup rfkill [ 1.081041] [BT_RFKILL]: bt_default device registered. [ 1.081245] Key type dns_resolver registered [ 1.081801] sensor_register_slave:mpu6880_gyro,id=50 [ 1.085881] Registered cp15_barrier emulation handler [ 1.086071] Registered setend emulation handler [ 1.088145] Loading compiled-in X.509 certificates [ 1.088317] zswap: loaded using pool lzo/zbud [ 1.089542] phy phy-ff770000.syscon:usb2-phy@e450.5: Looking up phy-supply from device tree [ 1.090430] phy phy-ff770000.syscon:usb2-phy@e450.6: Looking up phy-supply from device tree [ 1.090458] phy phy-ff770000.syscon:usb2-phy@e450.6: Looking up phy-supply property in node /syscon@ff770000/usb2-phy@e450/otg-port failed [ 1.090663] phy phy-ff770000.syscon:usb2-phy@e450.6: Looking up vbus-supply from device tree [ 1.090687] phy phy-ff770000.syscon:usb2-phy@e450.6: Looking up vbus-supply property in node /syscon@ff770000/usb2-phy@e450/otg-port failed [ 1.090733] phy phy-ff770000.syscon:usb2-phy@e450.6: Failed to get VBUS supply regulator [ 1.092739] phy phy-ff7c0000.phy.7: Looking up phy-supply from device tree [ 1.092766] phy phy-ff7c0000.phy.7: Looking up phy-supply property in node /phy@ff7c0000/dp-port failed [ 1.092989] phy phy-ff7c0000.phy.8: Looking up phy-supply from device tree [ 1.093012] phy phy-ff7c0000.phy.8: Looking up phy-supply property in node /phy@ff7c0000/usb3-port failed [ 1.093443] rockchip-iodomain ff320000.syscon:io-domains: Looking up pmu1830-supply from device tree [ 1.093774] rockchip-iodomain ff770000.syscon:io-domains: Looking up bt656-supply from device tree [ 1.093881] rockchip-iodomain ff770000.syscon:io-domains: Looking up audio-supply from device tree [ 1.093986] rockchip-iodomain ff770000.syscon:io-domains: Looking up sdmmc-supply from device tree [ 1.094093] rockchip-iodomain ff770000.syscon:io-domains: Looking up gpio1830-supply from device tree [ 1.094417] universal-charger usb-charger: GPIO lookup for consumer dc-det [ 1.094438] universal-charger usb-charger: using device tree for GPIO lookup [ 1.094460] of_get_named_gpiod_flags: can't parse 'dc-det-gpios' property of node '/usb-charger[0]' [ 1.094479] of_get_named_gpiod_flags: can't parse 'dc-det-gpio' property of node '/usb-charger[0]' [ 1.094498] universal-charger usb-charger: using lookup tables for GPIO lookup [ 1.094517] universal-charger usb-charger: lookup for GPIO dc-det failed [ 1.094536] universal-charger usb-charger: invalid dc det gpio! [ 1.096615] mmc1: new HS200 MMC card at address 0001 [ 1.097854] mmcblk1: mmc1:0001 DA4128 116 GiB [ 1.098202] pwm-backlight edp-backlight: GPIO lookup for consumer enable [ 1.098223] pwm-backlight edp-backlight: using device tree for GPIO lookup [ 1.098245] of_get_named_gpiod_flags: can't parse 'enable-gpios' property of node '/edp-backlight[0]' [ 1.098276] of_get_named_gpiod_flags: can't parse 'enable-gpio' property of node '/edp-backlight[0]' [ 1.098294] pwm-backlight edp-backlight: using lookup tables for GPIO lookup [ 1.098451] pwm-backlight edp-backlight: lookup for GPIO enable failed [ 1.098477] pwm-backlight edp-backlight: Looking up power-supply from device tree [ 1.098690] mmcblk1boot0: mmc1:0001 DA4128 partition 1 4.00 MiB [ 1.099494] mmcblk1boot1: mmc1:0001 DA4128 partition 2 4.00 MiB [ 1.100245] mmcblk1rpmb: mmc1:0001 DA4128 partition 3 16.0 MiB [ 1.101303] rockchip-drm display-subsystem: defer getting devfreq [ 1.101429] mmcblk1: p1 p2 [ 1.103683] rockchip-drm display-subsystem: bound ff900000.vop (ops 0xffffff8009075780) [ 1.104153] rockchip-drm display-subsystem: bound ff8f0000.vop (ops 0xffffff8009075780) [ 1.104328] rockchip-drm display-subsystem: failed to bind ff970000.edp (ops 0xffffff800906c3c0): -517 [ 1.104945] rockchip-drm display-subsystem: master bind failed: -517 [ 1.106001] panel-simple edp-panel: Looking up power-supply from device tree [ 1.106149] panel-simple edp-panel: GPIO lookup for consumer enable [ 1.106169] panel-simple edp-panel: using device tree for GPIO lookup [ 1.106229] of_get_named_gpiod_flags: parsed 'enable-gpios' property of node '/edp-panel[0]' - status (0) [ 1.106261] no flags found for enable [ 1.106283] panel-simple edp-panel: GPIO lookup for consumer reset [ 1.106301] panel-simple edp-panel: using device tree for GPIO lookup [ 1.106322] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/edp-panel[0]' [ 1.106377] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/edp-panel[0]' [ 1.106395] panel-simple edp-panel: using lookup tables for GPIO lookup [ 1.106414] panel-simple edp-panel: lookup for GPIO reset failed [ 1.111851] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 1.112315] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 1.112598] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x00010010 [ 1.112696] xhci-hcd xhci-hcd.2.auto: irq 225, io mem 0xfe800000 [ 1.113098] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.113122] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.113142] usb usb3: Product: xHCI Host Controller [ 1.113160] usb usb3: Manufacturer: Linux 4.4.202 xhci-hcd [ 1.113178] usb usb3: SerialNumber: xhci-hcd.2.auto [ 1.114110] hub 3-0:1.0: USB hub found [ 1.114174] hub 3-0:1.0: 1 port detected [ 1.114778] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 1.115043] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 1.115170] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.115411] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.115434] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.115452] usb usb4: Product: xHCI Host Controller [ 1.115470] usb usb4: Manufacturer: Linux 4.4.202 xhci-hcd [ 1.115487] usb usb4: SerialNumber: xhci-hcd.2.auto [ 1.116365] hub 4-0:1.0: USB hub found [ 1.116426] hub 4-0:1.0: 1 port detected [ 1.118836] xhci-hcd xhci-hcd.2.auto: remove, state 1 [ 1.118880] usb usb4: USB disconnect, device number 1 [ 1.119942] xhci-hcd xhci-hcd.2.auto: USB bus 4 deregistered [ 1.120215] xhci-hcd xhci-hcd.2.auto: remove, state 1 [ 1.120255] usb usb3: USB disconnect, device number 1 [ 1.125425] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller [ 1.125733] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 4 [ 1.125966] xhci-hcd xhci-hcd.3.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x00010010 [ 1.126060] xhci-hcd xhci-hcd.3.auto: irq 226, io mem 0xfe900000 [ 1.126485] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.126508] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.126527] usb usb4: Product: xHCI Host Controller [ 1.126545] usb usb4: Manufacturer: Linux 4.4.202 xhci-hcd [ 1.126562] usb usb4: SerialNumber: xhci-hcd.3.auto [ 1.127447] hub 4-0:1.0: USB hub found [ 1.127511] hub 4-0:1.0: 1 port detected [ 1.128080] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller [ 1.128372] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 5 [ 1.128507] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.128701] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.128722] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.128739] usb usb5: Product: xHCI Host Controller [ 1.128756] usb usb5: Manufacturer: Linux 4.4.202 xhci-hcd [ 1.128773] usb usb5: SerialNumber: xhci-hcd.3.auto [ 1.129658] hub 5-0:1.0: USB hub found [ 1.129718] hub 5-0:1.0: 1 port detected [ 1.133392] ehci-platform fe380000.usb: EHCI Host Controller [ 1.133747] ehci-platform fe380000.usb: new USB bus registered, assigned bus number 6 [ 1.133947] ehci-platform fe380000.usb: irq 27, io mem 0xfe380000 [ 1.137198] xhci-hcd xhci-hcd.2.auto: Host not halted after 16000 microseconds. [ 1.137220] xhci-hcd xhci-hcd.2.auto: Host controller not halted, aborting reset. [ 1.137599] xhci-hcd xhci-hcd.2.auto: USB bus 3 deregistered [ 1.150839] usb 1-1: new high-speed USB device number 2 using ehci-platform [ 1.156683] ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00 [ 1.157104] usb usb6: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.157125] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.157142] usb usb6: Product: EHCI Host Controller [ 1.157159] usb usb6: Manufacturer: Linux 4.4.202 ehci_hcd [ 1.157175] usb usb6: SerialNumber: fe380000.usb [ 1.158468] hub 6-0:1.0: USB hub found [ 1.158524] hub 6-0:1.0: 1 port detected [ 1.160110] ohci-platform fe3a0000.usb: Generic Platform OHCI controller [ 1.160869] ohci-platform fe3a0000.usb: new USB bus registered, assigned bus number 3 [ 1.161121] ohci-platform fe3a0000.usb: irq 28, io mem 0xfe3a0000 [ 1.216251] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 1.216293] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.216318] usb usb3: Product: Generic Platform OHCI controller [ 1.216373] usb usb3: Manufacturer: Linux 4.4.202 ohci_hcd [ 1.216398] usb usb3: SerialNumber: fe3a0000.usb [ 1.218267] hub 3-0:1.0: USB hub found [ 1.218391] hub 3-0:1.0: 1 port detected [ 1.220309] pwrseq_simple sdio-pwrseq: GPIO lookup for consumer reset [ 1.220371] pwrseq_simple sdio-pwrseq: using device tree for GPIO lookup [ 1.220447] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/sdio-pwrseq[0]' - status (0) [ 1.222824] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode. [ 1.222898] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller. [ 1.222932] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a [ 1.223006] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 24,32 bit host data width,256 deep fifo [ 1.223064] dwmmc_rockchip fe310000.dwmmc: Looking up vmmc-supply from device tree [ 1.223379] dwmmc_rockchip fe310000.dwmmc: Looking up vqmmc-supply from device tree [ 1.223638] dwmmc_rockchip fe310000.dwmmc: GPIO lookup for consumer wp [ 1.223664] dwmmc_rockchip fe310000.dwmmc: using device tree for GPIO lookup [ 1.223692] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/dwmmc@fe310000[0]' [ 1.223718] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/dwmmc@fe310000[0]' [ 1.223742] dwmmc_rockchip fe310000.dwmmc: using lookup tables for GPIO lookup [ 1.223767] dwmmc_rockchip fe310000.dwmmc: lookup for GPIO wp failed [ 1.223948] dwmmc_rockchip fe310000.dwmmc: allocated mmc-pwrseq [ 1.237155] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) [ 1.250224] dwmmc_rockchip fe310000.dwmmc: 1 slots initialized [ 1.251794] rockchip-dmc dmc: Looking up center-supply from device tree [ 1.252165] rockchip-dmc dmc: Failed to get leakage [ 1.252198] rockchip-dmc dmc: Looking up center-supply from device tree [ 1.252234] vdd_center: could not add device link dmc err -17 [ 1.252251] vdd_center: Failed to create debugfs directory [ 1.252929] rockchip-dmc dmc: avs=0 [ 1.252980] rockchip-dmc dmc: failed to get vop pn to msch rl [ 1.253279] rockchip-dmc dmc: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0 [ 1.253309] rockchip-dmc dmc: could not find power_model node [ 1.254028] of_get_named_gpiod_flags: can't parse 'simple-audio-card,hp-det-gpio' property of node '/speaker-sound[0]' [ 1.254043] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpio' property of node '/speaker-sound[0]' [ 1.296751] mmc2: queuing unknown CIS tuple 0x80 (2 bytes) [ 1.298419] mmc2: queuing unknown CIS tuple 0x80 (3 bytes) [ 1.301147] mmc2: queuing unknown CIS tuple 0x80 (3 bytes) [ 1.304202] mmc2: queuing unknown CIS tuple 0x80 (7 bytes) [ 1.307853] mmc2: queuing unknown CIS tuple 0x81 (9 bytes) [ 1.362131] mmc_host mmc2: Bus speed (slot 0) = 84500000Hz (slot req 90000000Hz, actual 84500000HZ div = 0) [ 1.377150] asoc-simple-card speaker-sound: ES8316 HiFi <-> ff890000.i2s mapping ok [ 1.377426] es8316 1-0011: ASoC: Failed to create Left Hp mixer debugfs file [ 1.377445] es8316 1-0011: ASoC: Failed to create Right Hp mixer debugfs file [ 1.377473] es8316 1-0011: ASoC: Failed to create HPCP L debugfs file [ 1.377490] es8316 1-0011: ASoC: Failed to create HPCP R debugfs file [ 1.377546] es8316 1-0011: ASoC: Failed to create HPVOL L debugfs file [ 1.377563] es8316 1-0011: ASoC: Failed to create HPVOL R debugfs file [ 1.379983] rockchip-drm display-subsystem: devfreq is ready [ 1.380587] rockchip-drm display-subsystem: bound ff900000.vop (ops 0xffffff8009075780) [ 1.380822] rockchip-drm display-subsystem: bound ff8f0000.vop (ops 0xffffff8009075780) [ 1.380963] rockchip-dp ff970000.edp: Looking up vcc-supply from device tree [ 1.380976] rockchip-dp ff970000.edp: Looking up vcc-supply property in node /edp@ff970000 failed [ 1.381017] rockchip-dp ff970000.edp: Looking up vccio-supply from device tree [ 1.381029] rockchip-dp ff970000.edp: Looking up vccio-supply property in node /edp@ff970000 failed [ 1.381119] rockchip-dp ff970000.edp: no DP phy configured [ 1.381156] rockchip-dp ff970000.edp: GPIO lookup for consumer hpd [ 1.381165] rockchip-dp ff970000.edp: using device tree for GPIO lookup [ 1.381178] of_get_named_gpiod_flags: can't parse 'hpd-gpios' property of node '/edp@ff970000[0]' [ 1.381189] of_get_named_gpiod_flags: can't parse 'hpd-gpio' property of node '/edp@ff970000[0]' [ 1.381199] rockchip-dp ff970000.edp: using lookup tables for GPIO lookup [ 1.381209] rockchip-dp ff970000.edp: lookup for GPIO hpd failed [ 1.382119] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 1.382136] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 1.382149] usb 1-1: Product: USB2.0 Hub [ 1.382516] rockchip-drm display-subsystem: bound ff970000.edp (ops 0xffffff800906c3c0) [ 1.383193] hub 1-1:1.0: USB hub found [ 1.383597] cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work] Not connected. Disabling cdn [ 1.383615] hub 1-1:1.0: 4 ports detected [ 1.383639] rockchip-drm display-subsystem: bound fec00000.dp (ops 0xffffff800906ad10) [ 1.383651] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 1.383659] [drm] No driver support for vblank timestamp query. [ 1.383869] rockchip-drm display-subsystem: failed to parse loader memory [ 1.397495] rockchip-vop ff900000.vop: [drm:vop_crtc_enable] Update mode to 1920x1080p60, type: 14 [ 1.420856] rockchip-dp ff970000.edp: [drm:analogix_dp_link_start] Enable downspread on the sink [ 1.424112] rockchip-dp ff970000.edp: Link Training Clock Recovery success [ 1.425657] rockchip-dp ff970000.edp: Link Training success! [ 1.581273] dwmmc_rockchip fe310000.dwmmc: Successfully tuned phase to 11 [ 1.585404] mmc2: queuing unknown CIS tuple 0x91 (3 bytes) [ 1.585448] mmc2: new ultra high speed SDR104 SDIO card at address 0001 [ 1.593150] vendor storage:20190527 ret = 0 [ 1.670304] Console: switching to colour frame buffer device 240x67 [ 1.729394] usb 3-1: new low-speed USB device number 2 using ohci-platform [ 1.747072] rockchip-drm display-subsystem: fb0: frame buffer device [ 1.754238] rk-hdmi-dp-sound hdmi-dp-sound: i2s-hifi <-> ff8a0000.i2s mapping ok [ 1.754288] hdmi-audio-codec hdmi-audio-codec.5.auto: ASoC: Failed to create Playback debugfs file [ 1.757854] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_isp1-supply from device tree [ 1.757896] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_isp1-supply property in node /power-management@ff310000/power-controller failed [ 1.758015] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_isp0-supply from device tree [ 1.758041] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_isp0-supply property in node /power-management@ff310000/power-controller failed [ 1.758142] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_gmac-supply from device tree [ 1.758165] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_gmac-supply property in node /power-management@ff310000/power-controller failed [ 1.758254] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_gpu-supply from device tree [ 1.758277] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_gpu-supply property in node /power-management@ff310000/power-controller failed [ 1.758404] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_rga-supply from device tree [ 1.758429] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_rga-supply property in node /power-management@ff310000/power-controller failed [ 1.758516] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_iep-supply from device tree [ 1.758537] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_iep-supply property in node /power-management@ff310000/power-controller failed [ 1.758768] dhd_module_init: in Dongle Host Driver, version 1.579.77.41.10 (r) [ 1.758794] ======== dhd_wlan_init_plat_data ======== [ 1.758811] dhd_wlan_init_gpio: WL_REG_ON=-1 [ 1.758826] dhd_wifi_platform_load: Enter [ 1.758865] Power-up adapter 'DHD generic adapter' [ 1.759582] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-keys/power[0]' - status (0) [ 1.759673] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-keys/lid[0]' - status (0) [ 1.759748] gpio-5 (Power): gpiod_set_debounce: missing set() or set_debounce() operations [ 1.759873] gpio-33 (Lid): gpiod_set_debounce: missing set() or set_debounce() operations [ 1.759936] wifi_platform_set_power = 1 [ 1.759954] ======== PULL WL_REG_ON(-1) HIGH! ======== [ 1.759971] [WLAN_RFKILL]: rockchip_wifi_power: 1 [ 1.759986] [WLAN_RFKILL]: wifi turn on power. -1 [ 1.760310] input: gpio-keys as /devices/platform/gpio-keys/input/input1 [ 1.762233] rk808-rtc rk808-rtc: setting system clock to 2019-11-30 18:04:49 UTC (1575137089) [ 1.762391] usb 1-1.2: new high-speed USB device number 3 using ehci-platform [ 1.762419] of_cfs_init [ 1.762480] of_cfs_init: OK [ 1.794403] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_vopl-supply from device tree [ 1.794437] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_vopl-supply property in node /power-management@ff310000/power-controller failed [ 1.794576] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_vdu-supply from device tree [ 1.794603] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_vdu-supply property in node /power-management@ff310000/power-controller failed [ 1.794704] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_vcodec-supply from device tree [ 1.794727] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_vcodec-supply property in node /power-management@ff310000/power-controller failed [ 1.796198] ALSA device list: [ 1.796216] #0: es8316-spk-sound [ 1.796230] #1: rk-hdmi-dp-sound [ 1.796736] dw-apb-uart ff1a0000.serial: got rx and tx dma channels [ 1.796901] md: Waiting for all devices to be available before autodetect [ 1.796909] md: If you don't use raid, use raid=noautodetect [ 1.861944] md: Autodetecting RAID arrays. [ 1.861969] md: Scanned 0 and added 0 devices. [ 1.861984] md: autorun ... [ 1.861998] md: ... autorun DONE. [ 1.905845] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null) [ 1.905919] VFS: Mounted root (ext4 filesystem) on device 179:2. [ 1.907517] devtmpfs: mounted [ 1.908179] Freeing unused kernel memory: 1216K [ 1.989025] usb 1-1.2: New USB device found, idVendor=0c45, idProduct=6321 [ 1.989057] usb 1-1.2: New USB device strings: Mfr=2, Product=1, SerialNumber=0 [ 1.989074] usb 1-1.2: Product: USB Camera [ 1.989091] usb 1-1.2: Manufacturer: Sonix Technology Co., Ltd. [ 1.992768] uvcvideo: Found UVC 1.00 device USB Camera (0c45:6321) [ 2.026958] usb 3-1: New USB device found, idVendor=258a, idProduct=001e [ 2.026990] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.027012] usb 3-1: Product: USB KEYBOARD [ 2.027029] usb 3-1: Manufacturer: HAILUCK CO.,LTD [ 2.036584] input: HAILUCK CO.,LTD USB KEYBOARD as /devices/platform/fe3a0000.usb/usb3/3-1/3-1:1.0/0003:258A:001E.0001/input/input2 [ 2.060520] wifi_platform_bus_enumerate device present 1 [ 2.060541] ======== Card detection to detect SDIO card! ======== [ 2.060550] mmc2:mmc host rescan start! [ 2.076692] bcmsdh_register: register client driver [ 2.076880] bcmsdh_sdmmc_probe: Enter num=1 [ 2.076972] bcmsdh_sdmmc_probe: Enter num=2 [ 2.076981] bus num (host idx)=2, slot num (rca)=1 [ 2.076990] found adapter info 'DHD generic adapter' [ 2.077028] sdioh_attach: set sd_f2_blocksize 256 [ 2.077057] sdioh_attach: sd clock rate = 0 [ 2.077211] dhdsdio_probe : no mutex held. set lock [ 2.077299] F1 signature read @0x18000000=0x15294345 [ 2.080101] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x9 pkg:0x2 [ 2.080608] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000 [ 2.080686] dhd_conf_set_chiprev: chip=0x4345, chiprev=9 [ 2.080958] CFG80211-ERROR) wl_setup_wiphy : Registering Vendor80211 [ 2.081821] CFG80211-ERROR) wl_init_prof : wl_init_prof: No profile [ 2.081989] wl_escan_attach: Enter [ 2.082021] wl_escan_init: Enter [ 2.082398] wl_create_event_handler(): thread:wl_escan_handler:ad started [ 2.082462] tsk Enter, tsk = 0xffffffc0f11f01b0 [ 2.082788] dhd_attach(): thread:dhd_watchdog_thread:ae started [ 2.083133] dhd_attach(): thread:dhd_dpc:af started [ 2.083476] dhd_attach(): thread:dhd_rxf:b0 started [ 2.083506] dhd_deferred_work_init: work queue initialized [ 2.083526] dhd_tcpack_suppress_set: TCP ACK Suppress mode 0 -> mode 2 [ 2.083589] dhd_bus_set_default_min_res_mask: Unhandled chip id [ 2.084037] systemd[1]: Failed to insert module 'autofs4': No such file or directory [ 2.084959] sdioh_cis_read: func_cis_ptr[0]=0x10ac [ 2.088808] hid-generic 0003:258A:001E.0001: input,hidraw0: USB HID v1.10 Keyboard [HAILUCK CO.,LTD USB KEYBOARD] on usb-fe3a0000.usb-1/input0 [ 2.095525] random: systemd: uninitialized urandom read (16 bytes read, 49 bits of entropy available) [ 2.097178] dw-apb-uart ff1a0000.serial: got rx and tx dma channels [ 2.097816] random: systemd: uninitialized urandom read (16 bytes read, 50 bits of entropy available) [ 2.099953] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN) [ 2.100856] systemd[1]: Detected architecture arm64. [ 2.101476] systemd[1]: Set hostname to . [ 2.119855] Dongle Host Driver, version 1.579.77.41.10 (r) [ 2.120697] wl_ext_iapsta_attach_netdev: ifidx=0, bssidx=0 [ 2.120715] Register interface [wlan0] MAC: 6c:21:a2:41:d9:44 [ 2.122304] dhd_tcpack_suppress_set: TCP ACK Suppress mode 2 -> mode 0 [ 2.122349] dhd_wl_ioctl: returning as busstate=0 [ 2.122362] dhd_dbg_detach_pkt_monitor, 2204 [ 2.122381] dhd_bus_devreset: == Power OFF == [ 2.122601] dhd_txglom_enable: enable 0 [ 2.122631] dhd_conf_set_txglom_params: txglom_mode=copy [ 2.122640] dhd_conf_set_txglom_params: txglomsize=0, deferred_tx_len=0 [ 2.122650] dhd_conf_set_txglom_params: txinrx_thres=128, dhd_txminmax=-1 [ 2.122660] dhd_conf_set_txglom_params: tx_max_offset=0, txctl_tmo_fix=300 [ 2.122677] dhd_bus_devreset: WLAN OFF DONE [ 2.125634] wifi_platform_set_power = 0 [ 2.125657] ======== PULL WL_REG_ON(-1) LOW! ======== [ 2.125669] [WLAN_RFKILL]: rockchip_wifi_power: 0 [ 2.125704] [WLAN_RFKILL]: wifi shut off power. [ 2.125716] dhdsdio_probe : the lock is released. [ 2.126990] bcmsdh_sdmmc: probe of mmc2:0001:3 failed with error -110 [ 2.127078] dhd_module_init: Exit err=0 [ 2.133308] input: HAILUCK CO.,LTD USB KEYBOARD Touchpad as /devices/platform/fe3a0000.usb/usb3/3-1/3-1:1.1/0003:258A:001E.0002/input/input3 [ 2.133551] random: systemd-gpt-aut: uninitialized urandom read (16 bytes read, 58 bits of entropy available) [ 2.133833] random: systemd-gpt-aut: uninitialized urandom read (16 bytes read, 58 bits of entropy available) [ 2.134243] dw-apb-uart ff1a0000.serial: got rx and tx dma channels [ 2.145508] random: systemd-cryptse: uninitialized urandom read (16 bytes read, 59 bits of entropy available) [ 2.169744] random: systemd-sysv-ge: uninitialized urandom read (16 bytes read, 60 bits of entropy available) [ 2.185083] hid-multitouch 0003:258A:001E.0002: input,hiddev0,hidraw1: USB HID v1.10 Mouse [HAILUCK CO.,LTD USB KEYBOARD] on usb-fe3a0000.usb-1/input1 [ 2.220857] random: systemd: uninitialized urandom read (16 bytes read, 61 bits of entropy available) [ 2.222442] random: systemd: uninitialized urandom read (16 bytes read, 61 bits of entropy available) [ 2.223227] random: systemd: uninitialized urandom read (16 bytes read, 61 bits of entropy available) [ 2.224901] random: systemd: uninitialized urandom read (16 bytes read, 61 bits of entropy available) [ 2.337830] systemd[1]: Configuration file /lib/systemd/system/partition-bootup.service is marked executable. Please remove executable permission bits. Proceeding anyway. [ 2.340559] systemd[1]: Configuration file /etc/systemd/system/rockpro-hciattach.service is marked executable. Please remove executable permission bits. Proceeding anyway. [ 2.353284] systemd[1]: Listening on Syslog Socket. [ 2.353719] systemd[1]: Listening on udev Control Socket. [ 2.353862] systemd[1]: Listening on Journal Socket (/dev/log). [ 2.354408] systemd[1]: Created slice System Slice. [ 2.354840] systemd[1]: Created slice system-serial\x2dgetty.slice. [ 2.355101] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ 2.355210] systemd[1]: Starting of Arbitrary Executable File Formats File System Automount Point not supported. [ 2.355506] dw-apb-uart ff1a0000.serial: got rx and tx dma channels [ 2.357558] systemd[1]: Reached target Remote File Systems. [ 2.357729] dw-apb-uart ff1a0000.serial: got rx and tx dma channels [ 2.360022] systemd[1]: Listening on Journal Socket. [ 2.360199] dw-apb-uart ff1a0000.serial: got rx and tx dma channels [ 2.365864] systemd[1]: Starting Load Kernel Modules... [ 2.366156] dw-apb-uart ff1a0000.serial: got rx and tx dma channels [ 2.370691] systemd[1]: Starting Remount Root and Kernel File Systems... [ 2.370996] dw-apb-uart ff1a0000.serial: got rx and tx dma channels [ 2.375923] systemd[1]: Starting Create list of required static device nodes for the current kernel... [ 2.376206] dw-apb-uart ff1a0000.serial: got rx and tx dma channels [ 2.385725] systemd[1]: Starting Restore / save the current clock... [ 2.386053] dw-apb-uart ff1a0000.serial: got rx and tx dma channels [ 2.388716] systemd[1]: Reached target User and Group Name Lookups. [ 2.391858] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 2.394584] systemd[1]: Reached target Paths. [ 2.396989] systemd[1]: Created slice User and Session Slice. [ 2.399566] systemd[1]: Reached target Slices. [ 2.401686] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ 2.405946] systemd[1]: Mounting Debug File System... [ 2.418965] systemd[1]: Starting Journal Service... [ 2.420670] systemd[1]: Created slice system-getty.slice. [ 2.424109] systemd[1]: Reached target Encrypted Volumes. [ 2.432671] systemd[1]: Mounting POSIX Message Queue File System... [ 2.435987] systemd[1]: Listening on udev Kernel Socket. [ 2.442644] systemd[1]: Mounted Debug File System. [ 2.452624] systemd[1]: Mounted POSIX Message Queue File System. [ 2.455139] systemd[1]: Started Load Kernel Modules. [ 2.470525] systemd[1]: Started Remount Root and Kernel File Systems. [ 2.474608] systemd[1]: Started Create list of required static device nodes for the current kernel. [ 2.478657] systemd[1]: Started Restore / save the current clock. [ 2.490248] systemd[1]: Starting Create Static Device Nodes in /dev... [ 2.494071] systemd[1]: Starting Load/Save Random Seed... [ 2.500190] systemd[1]: Activating swap /swapfile... [ 2.507644] systemd[1]: Starting Rebuild Hardware Database... [ 2.513690] systemd[1]: Mounting Configuration File System... [ 2.518802] systemd[1]: Mounting FUSE Control File System... [ 2.524158] systemd[1]: Starting Apply Kernel Variables... [ 2.532778] systemd[1]: Mounted Configuration File System. [ 2.539919] systemd[1]: Mounted FUSE Control File System. [ 2.585240] systemd[1]: Started Load/Save Random Seed. [ 2.590738] systemd[1]: Started Apply Kernel Variables. [ 2.590954] Adding 511996k swap on /swapfile. Priority:-1 extents:4 across:524284k SSFS [ 2.594280] systemd[1]: Activated swap /swapfile. [ 2.597509] systemd[1]: Started Create Static Device Nodes in /dev. [ 2.602459] systemd[1]: Starting udev Kernel Device Manager... [ 2.604247] systemd[1]: Reached target Local File Systems (Pre). [ 2.606906] systemd[1]: Reached target Local File Systems. [ 2.612235] systemd[1]: Starting Enable support for additional executable binary formats... [ 2.619714] systemd[1]: Reached target Swap. [ 2.632059] systemd[1]: Starting Raise network interfaces... [ 2.663429] systemd[1]: Started Enable support for additional executable binary formats. [ 2.725089] systemd[1]: Started udev Kernel Device Manager. [ 2.734162] systemd[1]: Started Journal Service. [ 2.749462] phy phy-ff770000.syscon:usb2-phy@e450.6: charger = USB_FLOATING_CHARGER [ 2.765572] systemd-journald[205]: Received request to flush runtime journal from PID 1 [ 3.745321] rockchip-saradc ff100000.saradc: Looking up vref-supply from device tree [ 3.745354] rockchip-saradc ff100000.saradc: Looking up vref-supply property in node /saradc@ff100000 failed [ 3.745382] ff100000.saradc supply vref not found, using dummy regulator [ 3.748319] phy phy-pcie-phy.9: Looking up phy-supply from device tree [ 3.748376] phy phy-pcie-phy.9: Looking up phy-supply property in node /pcie-phy failed [ 3.751309] rockchip-pcie f8000000.pcie: GPIO lookup for consumer ep [ 3.751362] rockchip-pcie f8000000.pcie: using device tree for GPIO lookup [ 3.751456] of_get_named_gpiod_flags: parsed 'ep-gpios' property of node '/pcie@f8000000[0]' - status (0) [ 3.751794] rockchip-pcie f8000000.pcie: Looking up vpcie12v-supply from device tree [ 3.751810] rockchip-pcie f8000000.pcie: Looking up vpcie12v-supply property in node /pcie@f8000000 failed [ 3.751864] rockchip-pcie f8000000.pcie: no vpcie12v regulator found [ 3.751876] rockchip-pcie f8000000.pcie: Looking up vpcie3v3-supply from device tree [ 3.751888] rockchip-pcie f8000000.pcie: Looking up vpcie3v3-supply property in node /pcie@f8000000 failed [ 3.751908] rockchip-pcie f8000000.pcie: no vpcie3v3 regulator found [ 3.751920] rockchip-pcie f8000000.pcie: Looking up vpcie1v8-supply from device tree [ 3.751932] rockchip-pcie f8000000.pcie: Looking up vpcie1v8-supply property in node /pcie@f8000000 failed [ 3.751952] rockchip-pcie f8000000.pcie: no vpcie1v8 regulator found [ 3.751962] rockchip-pcie f8000000.pcie: Looking up vpcie0v9-supply from device tree [ 3.751976] rockchip-pcie f8000000.pcie: Looking up vpcie0v9-supply property in node /pcie@f8000000 failed [ 3.751995] rockchip-pcie f8000000.pcie: no vpcie0v9 regulator found [ 3.752007] rockchip-pcie f8000000.pcie: missing optional "memory-region" property [ 3.752020] rockchip-pcie f8000000.pcie: missing optional "rockchip,dma_trx_enabled" property [ 3.752031] rockchip-pcie f8000000.pcie: missing optional "rockchip,deferred" property [ 3.752053] rockchip-pcie f8000000.pcie: calling really probe [ 3.752063] rockchip-pcie f8000000.pcie: PCIe asserting reset [ 3.752100] rockchip-pcie f8000000.pcie: advertising gen2/1 training [ 3.752137] rockchip-pcie f8000000.pcie: PCIe reset released [ 3.764542] mali ff9a0000.gpu: Looking up mali-supply from device tree [ 3.764710] mali ff9a0000.gpu: leakage=26 [ 3.764724] mali ff9a0000.gpu: Looking up mali-supply from device tree [ 3.764740] vdd_gpu: could not add device link ff9a0000.gpu err -17 [ 3.764748] vdd_gpu: Failed to create debugfs directory [ 3.767455] mali ff9a0000.gpu: avs=0 [ 3.769354] mali ff9a0000.gpu: GPU identified as 0x0860 r2p0 status 0 [ 3.772123] mali ff9a0000.gpu: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 [ 3.772277] I : [File] : drivers/gpu/arm/midgard_for_linux/backend/gpu/mali_kbase_devfreq.c; [Line] : 332; [Func] : kbase_devfreq_init(); success initing power_model_simple. [ 3.773189] mali ff9a0000.gpu: Probed as mali0 [ 3.825619] [BT_RFKILL]: Enter rfkill_rk_set_power [ 3.825645] [BT_RFKILL]: Set blocked:1 [ 3.825653] [BT_RFKILL]: bt shut off power [ 4.139959] dhd_ioctl_entry: Interface is down [ 4.139972] Error getting the SSID [ 4.217759] dhd_open: Enter ffffffc0f16ee000 [ 4.217782] dhd_open : no mutex held. set lock [ 4.217795] Dongle Host Driver, version 1.579.77.41.10 (r) [ 4.217805] wl_ext_iapsta_attach_netdev: ifidx=0, bssidx=0 [ 4.217814] wl_android_wifi_on in 1 [ 4.217822] wl_android_wifi_on in 2: g_wifi_on=0 [ 4.217830] wifi_platform_set_power = 1 [ 4.217838] ======== PULL WL_REG_ON(-1) HIGH! ======== [ 4.217845] [WLAN_RFKILL]: rockchip_wifi_power: 1 [ 4.217854] [WLAN_RFKILL]: wifi turn on power. -1 [ 4.245688] random: nonblocking pool is initialized [ 4.252182] rockchip-pcie f8000000.pcie: PCIe link training gen1 timed out. [ 4.252194] rockchip-pcie f8000000.pcie: init port failed [ 4.252215] rockchip-pcie f8000000.pcie: probe init failed [ 4.252232] rockchip-pcie f8000000.pcie: PCIe probe failed. [ 4.252431] rockchip-pcie: probe of f8000000.pcie failed with error -110 [ 4.267646] [BT_RFKILL]: Enter rfkill_rk_set_power [ 4.267665] [BT_RFKILL]: Set blocked:0 [ 4.267672] [BT_RFKILL]: Enter rfkill_rk_sleep_bt [ 4.267682] [BT_RFKILL]: *** bt sleep: 0 *** [ 4.288402] [BT_RFKILL]: ENABLE UART_RTS [ 4.294678] FAT-fs (mmcblk1p1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! [ 4.389432] [BT_RFKILL]: DISABLE UART_RTS [ 4.389531] [BT_RFKILL]: bt turn on power [ 4.518632] sdio_reset_comm(): [ 4.547326] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) [ 4.564732] mmc_host mmc2: Bus speed (slot 0) = 100000Hz (slot req 100000Hz, actual 100000HZ div = 0) [ 4.625921] mmc2: queuing unknown CIS tuple 0x80 (2 bytes) [ 4.632838] mmc2: queuing unknown CIS tuple 0x80 (3 bytes) [ 4.639406] mmc2: queuing unknown CIS tuple 0x80 (3 bytes) [ 4.651292] mmc2: queuing unknown CIS tuple 0x80 (7 bytes) [ 4.857770] [BT_RFKILL]: Enter rfkill_rk_set_power [ 4.857832] [BT_RFKILL]: Set blocked:0 [ 4.857851] [BT_RFKILL]: Enter rfkill_rk_sleep_bt [ 4.857871] [BT_RFKILL]: *** bt sleep: 0 *** [ 4.857996] [BT_RFKILL]: ENABLE UART_RTS [ 4.891602] mmc_host mmc2: Bus speed (slot 0) = 84500000Hz (slot req 90000000Hz, actual 84500000HZ div = 0) [ 4.958457] [BT_RFKILL]: DISABLE UART_RTS [ 4.958538] [BT_RFKILL]: bt turn on power [ 6.380742] dwmmc_rockchip fe310000.dwmmc: Successfully tuned phase to 93 [ 6.381183] sdioh_start: set sd_f2_blocksize 256 [ 6.384797] dhd_bus_devreset: == WLAN ON == [ 6.385537] F1 signature read @0x18000000=0x15294345 [ 6.398100] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x9 pkg:0x2 [ 6.400930] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000 [ 6.401146] dhd_bus_set_default_min_res_mask: Unhandled chip id [ 6.402382] dhd_conf_read_config: Ignore config file /lib/firmware/brcm/config.txt [ 6.402431] Final fw_path=/lib/firmware/brcm/fw_bcm43456c5_ag.bin [ 6.402449] Final nv_path=/lib/firmware/brcm/nvram_ap6256.txt [ 6.402464] Final clm_path=/lib/firmware/brcm/clm.blob [ 6.402480] Final conf_path=/lib/firmware/brcm/config.txt [ 6.404572] dhd_os_open_image: /lib/firmware/brcm/fw_bcm43456c5_ag.bin (482927 bytes) open success [ 6.481333] dhd_os_open_image: /lib/firmware/brcm/nvram_ap6256.txt (2196 bytes) open success [ 6.482270] NVRAM version: AP6256_NVRAM_V1.1_08252017 [ 6.483231] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded. [ 6.559602] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us) [ 6.560115] dhd_get_memdump_info: File [/data/misc/wifi/.memdump.info] doesn't exist [ 6.560129] dhd_get_memdump_info: MEMDUMP ENABLED = 2 [ 6.562804] Disable tdls_auto_op failed. -1 [ 6.562825] dhd_tcpack_suppress_set: TCP ACK Suppress mode 0 -> mode 1 [ 6.565854] dhd_apply_default_clm: Ignore clm file /lib/firmware/brcm/clm.blob [ 6.568807] Firmware up: op_mode=0x0005, MAC=6c:21:a2:41:d9:44 [ 6.590914] Driver: 1.579.77.41.10 (r) Firmware: wl0: Jun 16 2017 12:38:26 version 7.45.96.2 (66c4e21@sh-git) (r) FWID 01-1813af84 CLM: 9.2.9 [ 6.591536] dhd_txglom_enable: enable 1 [ 6.591553] dhd_conf_set_txglom_params: txglom_mode=copy [ 6.591559] dhd_conf_set_txglom_params: txglomsize=36, deferred_tx_len=0 [ 6.591566] dhd_conf_set_txglom_params: txinrx_thres=128, dhd_txminmax=-1 [ 6.591590] dhd_conf_set_txglom_params: tx_max_offset=0, txctl_tmo_fix=300 [ 6.591602] dhd_conf_get_disable_proptx: fw_proptx=1, disable_proptx=-1 [ 6.593502] dhd_wlfc_hostreorder_init(): successful bdcv2 tlv signaling, 64 [ 6.595994] dhd_pno_init: Support Android Location Service [ 6.616147] CFG80211-ERROR) wl_cfg80211_event : Event handler is not created [ 6.617730] rtt_do_get_ioctl: failed to send getbuf proxd iovar (CMD ID : 1), status=-23 [ 6.617773] dhd_rtt_init : FTM is not supported [ 6.617788] dhd_preinit_ioctls: SensorHub diabled 0 [ 6.618748] dhd_preinit_ioctls failed to set ShubHub disable [ 6.622640] dhd_conf_set_country: set country CN, revision 38 [ 6.622660] CFG80211-ERROR) wl_cfg80211_event : Event handler is not created [ 6.626084] Country code: CN (CN/38) [ 6.630109] CONFIG-ERROR) dhd_conf_set_intiovar: txbf setting failed -23 [ 6.630778] wl_android_wifi_on: Success [ 6.672509] dhd_open : the lock is released. [ 6.672545] dhd_open: Exit ret=0 [ 6.806871] serial8250_request_dma: 99 callbacks suppressed [ 6.806906] dw-apb-uart ff1a0000.serial: got rx and tx dma channels [ 6.878497] dw-apb-uart ff1a0000.serial: got rx and tx dma channels [ 6.991955] dw-apb-uart ff1a0000.serial: got rx and tx dma channels [ 7.135576] dw-apb-uart ff1a0000.serial: got rx and tx dma channels [ 7.190823] dw-apb-uart ff1a0000.serial: got rx and tx dma channels [ 7.236869] P2P interface registered [ 7.236897] wl_cfgp2p_add_p2p_disc_if: wdev: ffffffc0eff32400, wdev->net: (null) [ 7.247233] WLC_E_IF: NO_IF set, event Ignored [ 7.248916] P2P interface started [ 7.282993] wl_run_escan: LEGACY_SCAN sync ID: 0, bssidx: 0 [ 9.453618] dw-apb-uart ff1a0000.serial: got rx and tx dma channels [ 9.461782] dw-apb-uart ff1a0000.serial: got rx and tx dma channels [ 9.534905] dw-apb-uart ff1a0000.serial: got rx and tx dma channels [ 9.652988] wl_run_escan: LEGACY_SCAN sync ID: 1, bssidx: 0 [ 9.713110] dw-apb-uart ff1a0000.serial: got rx and tx dma channels [ 9.716292] dw-apb-uart ff1a0000.serial: got rx and tx dma channels [ 14.769282] serial8250_request_dma: 17 callbacks suppressed [ 14.769319] dw-apb-uart ff1a0000.serial: got rx and tx dma channels [ 14.769908] dw-apb-uart ff1a0000.serial: got rx and tx dma channels [ 14.792049] dw-apb-uart ff1a0000.serial: got rx and tx dma channels [ 14.795315] dw-apb-uart ff1a0000.serial: got rx and tx dma channels [ 20.176943] wl_run_escan: LEGACY_SCAN sync ID: 2, bssidx: 0 [ 22.541691] Connecting with 78:24:af:7a:69:88 ssid "ASUS", len (4) channel=4 [ 22.545226] dhd_dbg_start_pkt_monitor, 1724 [ 22.591210] wl_iw_event: Link UP with 78:24:af:7a:69:88 [ 22.591507] wl_bss_connect_done succeeded with 78:24:af:7a:69:88 [ 22.681257] wl_bss_connect_done succeeded with 78:24:af:7a:69:88 vndr_oui: 00-10-18 [ 26.921975] [BT_RFKILL]: Enter rfkill_rk_set_power [ 26.921990] [BT_RFKILL]: Set blocked:0 [ 26.921995] [BT_RFKILL]: Enter rfkill_rk_sleep_bt [ 26.922003] [BT_RFKILL]: *** bt sleep: 0 *** [ 26.922043] [BT_RFKILL]: ENABLE UART_RTS [ 27.022688] [BT_RFKILL]: DISABLE UART_RTS [ 27.022772] [BT_RFKILL]: bt turn on power [ 33.115935] wl_run_escan: LEGACY_SCAN sync ID: 3, bssidx: 0 [ 75.922726] CFG80211-ERROR) wl_is_linkdown : Link down Reason : WLC_E_DEAUTH_IND [ 75.922797] link down if wlan0 may call cfg80211_disconnected. event : 6, reason=7 from 78:24:af:7a:69:88 [ 75.922821] dhd_dbg_stop_pkt_monitor, 1963 [ 75.926209] wl_iw_event: Link Down with 78:24:af:7a:69:88, reason=2 [ 75.926416] CFG80211-ERROR) wl_cfg80211_tdls_config : No change in tdls state. Do nothing. tdls_enable:1 [ 75.926445] CFG80211-ERROR) wl_is_linkdown : Link down Reason : WLC_E_LINK [ 75.926473] CFG80211-ERROR) wl_cfg80211_tdls_config : No change in tdls state. Do nothing. tdls_enable:1 [ 76.157140] Connecting with 78:24:af:7a:69:88 ssid "ASUS", len (4) channel=4 [ 76.158741] dhd_dbg_start_pkt_monitor, 1724 [ 76.200780] wl_iw_event: Link UP with 78:24:af:7a:69:88 [ 76.200976] wl_bss_connect_done succeeded with 78:24:af:7a:69:88 [ 76.233774] wl_run_escan: LEGACY_SCAN sync ID: 4, bssidx: 0 [ 76.343041] wl_bss_connect_done succeeded with 78:24:af:7a:69:88 vndr_oui: 00-10-18 [ 116.978961] PM: suspend entry 2019-11-30 18:06:44.716505681 UTC [ 116.978987] PM: Syncing filesystems ... done. [ 116.986680] PM: Preparing system for sleep (mem) [ 116.987271] Freezing user space processes ... (elapsed 0.005 seconds) done. [ 116.992443] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 116.994394] PM: Suspending system (mem) [ 116.994402] Suspending console(s) (use no_console_suspend to debug) [ 116.994617] [BT_RFKILL]: Enter rfkill_rk_pm_prepare [ 116.994619] [BT_RFKILL]: Disable UART_RTS [ 116.994708] [BT_RFKILL]: enable irq for bt wakeup host [ 116.999067] bcmsdh_sdmmc_suspend Enter func->num=2 [ 116.999072] dhdsdio_suspend Enter [ 116.999080] bcmsdh_sdmmc_suspend Exit [ 116.999087] bcmsdh_sdmmc_suspend Enter func->num=1 [ 117.099269] [WLAN_RFKILL]: Enter rfkill_wlan_suspend [ 117.236769] rockchip-dmc dmc: failed to get dfi event [ 117.237966] PM: suspend of devices complete after 242.458 msecs [ 117.241722] LDO_REG2: No configuration [ 117.249238] PM: late suspend of devices complete after 3.134 msecs [ 117.251707] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_edp-supply from device tree [ 117.251723] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_edp-supply property in node /power-management@ff310000/power-controller failed [ 117.251786] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_vopb-supply from device tree [ 117.251796] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_vopb-supply property in node /power-management@ff310000/power-controller failed [ 117.251839] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_vo-supply from device tree [ 117.251848] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_vo-supply property in node /power-management@ff310000/power-controller failed [ 117.251945] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_vio-supply from device tree [ 117.251954] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_vio-supply property in node /power-management@ff310000/power-controller failed [ 117.252161] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_sd-supply from device tree [ 117.252170] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_sd-supply property in node /power-management@ff310000/power-controller failed [ 117.252338] PM: noirq suspend of devices complete after 3.089 msecs [ 117.252344] Disabling non-boot CPUs ... [ 117.254004] CPU1: shutdown [ 117.254011] psci: CPU1 killed. [ 117.265978] CPU2: shutdown [ 117.276679] psci: Retrying again to check for CPU kill [ 117.276685] psci: CPU2 killed. [ 117.284444] CPU3: shutdown [ 117.294676] psci: Retrying again to check for CPU kill [ 117.294680] psci: CPU3 killed. [ 117.302006] CPU4: shutdown [ 117.312666] psci: Retrying again to check for CPU kill [ 117.312671] psci: CPU4 killed. [ 117.319475] CPU5: shutdown [ 117.329664] psci: Retrying again to check for CPU kill [ 117.329668] psci: CPU5 killed. [ 117.335188] Enabling non-boot CPUs ... [ 117.338727] Detected VIPT I-cache on CPU1 [ 117.338760] CPU1: found redistributor 1 region 0:0x00000000fef20000 [ 117.338819] CPU1: update cpu_capacity 401 [ 117.338823] CPU1: Booted secondary processor [410fd034] [ 117.339357] CPU1 is up [ 117.344757] Detected VIPT I-cache on CPU2 [ 117.344778] CPU2: found redistributor 2 region 0:0x00000000fef40000 [ 117.344818] CPU2: update cpu_capacity 401 [ 117.344822] CPU2: Booted secondary processor [410fd034] [ 117.345394] CPU2 is up [ 117.350972] Detected VIPT I-cache on CPU3 [ 117.350993] CPU3: found redistributor 3 region 0:0x00000000fef60000 [ 117.351033] CPU3: update cpu_capacity 401 [ 117.351037] CPU3: Booted secondary processor [410fd034] [ 117.351824] CPU3 is up [ 117.360223] Detected PIPT I-cache on CPU4 [ 117.360253] CPU4: found redistributor 100 region 0:0x00000000fef80000 [ 117.360317] CPU4: update cpu_capacity 1024 [ 117.360321] CPU4: Booted secondary processor [410fd082] [ 117.361828] cpu cpu4: Looking up cpu-supply from device tree [ 117.362749] cpu cpu4: avs=0 [ 117.362894] cpu cpu4: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 [ 117.362917] cpu cpu4: failed to read out thermal zone (-11) [ 117.363437] cpu cpu4: failed to find power_model node [ 117.363701] CPU4 is up [ 117.372543] Detected PIPT I-cache on CPU5 [ 117.372563] CPU5: found redistributor 101 region 0:0x00000000fefa0000 [ 117.372606] CPU5: update cpu_capacity 1024 [ 117.372609] CPU5: Booted secondary processor [410fd082] [ 117.374793] CPU5 is up [ 117.377862] PM: noirq resume of devices complete after 2.166 msecs [ 117.380345] PM: early resume of devices complete after 1.991 msecs [ 117.404866] dw-apb-uart ff180000.serial: got rx and tx dma channels [ 117.404979] dw-apb-uart ff1a0000.serial: got rx and tx dma channels [ 117.406563] rockchip-dmc dmc: failed to get dfi event [ 117.406657] rockchip-vop ff900000.vop: [drm:vop_crtc_enable] Update mode to 1920x1080p0, type: 14 [ 117.429946] rockchip-dp ff970000.edp: [drm:analogix_dp_link_start] Enable downspread on the sink [ 117.433040] rockchip-dp ff970000.edp: Link Training Clock Recovery success [ 117.434504] rockchip-dp ff970000.edp: Link Training success! [ 117.592775] [WLAN_RFKILL]: Enter rfkill_wlan_resume [ 117.594444] Suspended for 0.668 seconds [ 117.615865] mmc_host mmc2: Bus speed (slot 0) = 84500000Hz (slot req 90000000Hz, actual 84500000HZ div = 0) [ 117.615994] cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work] Not connected. Disabling cdn [ 117.616136] bcmsdh_sdmmc_resume Enter func->num=1 [ 117.616143] bcmsdh_sdmmc_resume Enter func->num=2 [ 117.616147] dhdsdio_resume Enter [ 117.616151] bcmsdh_sdmmc_resume Exit [ 117.765983] PM: resume of devices complete after 385.546 msecs [ 117.772626] [BT_RFKILL]: Enter rfkill_rk_pm_complete [ 117.772631] [BT_RFKILL]: ** disable irq [ 117.772641] [BT_RFKILL]: Enable UART_RTS [ 117.773657] PM: Finishing wakeup. [ 117.773667] Restarting tasks ... [ 117.774082] usb 3-1: USB disconnect, device number 2 [ 117.775369] usb 1-1.2: USB disconnect, device number 3 [ 117.783548] done. [ 117.784360] PM: suspend exit 2019-11-30 18:06:46.190744191 UTC [ 117.851847] CFG80211-ERROR) wl_cfg80211_disconnect : Reason 3 [ 117.851893] dhd_dbg_stop_pkt_monitor, 1963 [ 117.854048] wl_iw_event: Link Down with 78:24:af:7a:69:88, reason=2 [ 117.854149] CFG80211-ERROR) wl_is_linkdown : Link down Reason : WLC_E_LINK [ 117.854176] link down if wlan0 may call cfg80211_disconnected. event : 16, reason=2 from 78:24:af:7a:69:88 [ 117.854183] dhd_dbg_stop_pkt_monitor, 1963 [ 117.854797] CFG80211-ERROR) wl_cfg80211_tdls_config : No change in tdls state. Do nothing. tdls_enable:1 [ 117.855039] CFG80211-ERROR) wl_is_linkdown : Link down Reason : WLC_E_DEAUTH [ 117.855061] CFG80211-ERROR) wl_cfg80211_tdls_config : No change in tdls state. Do nothing. tdls_enable:1 [ 117.940691] usb 1-1.2: new high-speed USB device number 4 using ehci-platform [ 118.092922] dhd_stop: Enter ffffffc0f16ee000 [ 118.094663] usb 3-1: new low-speed USB device number 3 using ohci-platform [ 118.099568] WLC_E_IF: NO_IF set, event Ignored [ 118.099586] CFG80211-ERROR) wl_cfgp2p_down : Clean up the p2p discovery IF [ 118.099664] wl_cfgp2p_del_p2p_disc_if: wdev: ffffffc0eff32400, wdev->net: (null) [ 118.099696] CFGP2P-ERROR) wl_cfgp2p_disable_discovery : do nothing, not initialized [ 118.099708] Exit. P2P interface stopped [ 118.105761] P2P interface unregistered [ 118.105805] CFGP2P-ERROR) wl_cfgp2p_deinit_priv : In [ 118.107933] dhd_tcpack_suppress_set: TCP ACK Suppress mode 1 -> mode 0 [ 118.107964] wl_android_wifi_off in 1 [ 118.107975] wl_android_wifi_off in 2: g_wifi_on=1, on_failure=1 [ 118.109667] dhd_dbg_detach_pkt_monitor, 2204 [ 118.109692] dhd_bus_devreset: == Power OFF == [ 118.110031] dhd_txglom_enable: enable 0 [ 118.110046] dhd_conf_set_txglom_params: txglom_mode=copy [ 118.110056] dhd_conf_set_txglom_params: txglomsize=0, deferred_tx_len=0 [ 118.110066] dhd_conf_set_txglom_params: txinrx_thres=128, dhd_txminmax=-1 [ 118.110076] dhd_conf_set_txglom_params: tx_max_offset=0, txctl_tmo_fix=300 [ 118.110085] dhd_bus_devreset: WLAN OFF DONE [ 118.110333] wifi_platform_set_power = 0 [ 118.110345] ======== PULL WL_REG_ON(-1) LOW! ======== [ 118.110357] [WLAN_RFKILL]: rockchip_wifi_power: 0 [ 118.110384] [WLAN_RFKILL]: wifi shut off power. [ 118.110394] wl_android_wifi_off out [ 118.110405] wl_ext_iapsta_dettach_netdev: ifidx=0 [ 118.110451] dhd_stop: Exit [ 118.169001] usb 1-1.2: New USB device found, idVendor=0c45, idProduct=6321 [ 118.169015] usb 1-1.2: New USB device strings: Mfr=2, Product=1, SerialNumber=0 [ 118.169020] usb 1-1.2: Product: USB Camera [ 118.169026] usb 1-1.2: Manufacturer: Sonix Technology Co., Ltd. [ 118.171915] uvcvideo: Found UVC 1.00 device USB Camera (0c45:6321) [ 118.270223] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 118.270534] dhd_open: Enter ffffffc0f16ee000 [ 118.270546] dhd_open : no mutex held. set lock [ 118.270568] Dongle Host Driver, version 1.579.77.41.10 (r) [ 118.270582] wl_ext_iapsta_attach_netdev: ifidx=0, bssidx=0 [ 118.270681] wl_android_wifi_on in 1 [ 118.270893] wl_android_wifi_on in 2: g_wifi_on=0 [ 118.270907] wifi_platform_set_power = 1 [ 118.270917] ======== PULL WL_REG_ON(-1) HIGH! ======== [ 118.270928] [WLAN_RFKILL]: rockchip_wifi_power: 1 [ 118.270939] [WLAN_RFKILL]: wifi turn on power. -1 [ 118.394796] usb 3-1: New USB device found, idVendor=258a, idProduct=001e [ 118.394816] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 118.394824] usb 3-1: Product: USB KEYBOARD [ 118.394831] usb 3-1: Manufacturer: HAILUCK CO.,LTD [ 118.403842] input: HAILUCK CO.,LTD USB KEYBOARD as /devices/platform/fe3a0000.usb/usb3/3-1/3-1:1.0/0003:258A:001E.0003/input/input5 [ 118.459879] hid-generic 0003:258A:001E.0003: input,hidraw0: USB HID v1.10 Keyboard [HAILUCK CO.,LTD USB KEYBOARD] on usb-fe3a0000.usb-1/input0 [ 118.502000] input: HAILUCK CO.,LTD USB KEYBOARD Touchpad as /devices/platform/fe3a0000.usb/usb3/3-1/3-1:1.1/0003:258A:001E.0004/input/input6 [ 118.557110] hid-multitouch 0003:258A:001E.0004: input,hiddev0,hidraw1: USB HID v1.10 Mouse [HAILUCK CO.,LTD USB KEYBOARD] on usb-fe3a0000.usb-1/input1 [ 118.571881] sdio_reset_comm(): [ 118.599847] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) [ 118.615964] mmc_host mmc2: Bus speed (slot 0) = 100000Hz (slot req 100000Hz, actual 100000HZ div = 0) [ 118.691966] sdio_read_cis: 1 callbacks suppressed [ 118.691985] mmc2: queuing unknown CIS tuple 0x80 (2 bytes) [ 118.698288] mmc2: queuing unknown CIS tuple 0x80 (3 bytes) [ 118.704261] mmc2: queuing unknown CIS tuple 0x80 (3 bytes) [ 118.715013] mmc2: queuing unknown CIS tuple 0x80 (7 bytes) [ 118.728307] mmc2: queuing unknown CIS tuple 0x81 (9 bytes) [ 118.937132] mmc_host mmc2: Bus speed (slot 0) = 84500000Hz (slot req 90000000Hz, actual 84500000HZ div = 0) [ 118.945188] dwmmc_rockchip fe310000.dwmmc: All phases work, using default phase 0. [ 118.945243] sdioh_start: set sd_f2_blocksize 256 [ 118.945480] dhd_bus_devreset: == WLAN ON == [ 118.945552] F1 signature read @0x18000000=0x15294345 [ 118.949512] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x9 pkg:0x2 [ 118.950437] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000 [ 118.950497] dhd_bus_set_default_min_res_mask: Unhandled chip id [ 118.951116] dhd_conf_read_config: Ignore config file /lib/firmware/brcm/config.txt [ 118.951143] Final fw_path=/lib/firmware/brcm/fw_bcm43456c5_ag.bin [ 118.951150] Final nv_path=/lib/firmware/brcm/nvram_ap6256.txt [ 118.951155] Final clm_path=/lib/firmware/brcm/clm.blob [ 118.951160] Final conf_path=/lib/firmware/brcm/config.txt [ 118.951460] dhd_os_open_image: /lib/firmware/brcm/fw_bcm43456c5_ag.bin (482927 bytes) open success [ 119.020792] dhd_os_open_image: /lib/firmware/brcm/nvram_ap6256.txt (2196 bytes) open success [ 119.020864] NVRAM version: AP6256_NVRAM_V1.1_08252017 [ 119.021387] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded. [ 119.098212] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us) [ 119.119354] dhd_get_memdump_info: File [/data/misc/wifi/.memdump.info] doesn't exist [ 119.119371] dhd_get_memdump_info: MEMDUMP ENABLED = 2 [ 119.123042] dhd_tcpack_suppress_set: TCP ACK Suppress mode 0 -> mode 1 [ 119.123347] dhd_apply_default_clm: Ignore clm file /lib/firmware/brcm/clm.blob [ 119.125224] Firmware up: op_mode=0x0005, MAC=6c:21:a2:41:d9:44 [ 119.141343] Driver: 1.579.77.41.10 (r) Firmware: wl0: Jun 16 2017 12:38:26 version 7.45.96.2 (66c4e21@sh-git) (r) FWID 01-1813af84 CLM: 9.2.9 [ 119.142126] dhd_txglom_enable: enable 1 [ 119.142141] dhd_conf_set_txglom_params: txglom_mode=copy [ 119.142151] dhd_conf_set_txglom_params: txglomsize=36, deferred_tx_len=0 [ 119.142161] dhd_conf_set_txglom_params: txinrx_thres=128, dhd_txminmax=-1 [ 119.142171] dhd_conf_set_txglom_params: tx_max_offset=0, txctl_tmo_fix=300 [ 119.142188] dhd_conf_get_disable_proptx: fw_proptx=1, disable_proptx=-1 [ 119.144976] dhd_wlfc_hostreorder_init(): successful bdcv2 tlv signaling, 64 [ 119.147299] dhd_pno_init: Support Android Location Service [ 119.167048] CFG80211-ERROR) wl_cfg80211_event : Event handler is not created [ 119.168488] rtt_do_get_ioctl: failed to send getbuf proxd iovar (CMD ID : 1), status=-23 [ 119.168507] dhd_rtt_init : FTM is not supported [ 119.168519] dhd_preinit_ioctls: SensorHub diabled 0 [ 119.170172] dhd_preinit_ioctls failed to set ShubHub disable [ 119.173347] dhd_conf_set_country: set country CN, revision 38 [ 119.173364] CFG80211-ERROR) wl_cfg80211_event : Event handler is not created [ 119.176384] Country code: CN (CN/38) [ 119.179962] CONFIG-ERROR) dhd_conf_set_intiovar: txbf setting failed -23 [ 119.180308] wl_android_wifi_on: Success [ 119.210559] dhd_open : the lock is released. [ 119.210583] dhd_open: Exit ret=0 [ 119.287468] P2P interface registered [ 119.287497] wl_cfgp2p_add_p2p_disc_if: wdev: ffffffc0effa6c00, wdev->net: (null) [ 119.300013] WLC_E_IF: NO_IF set, event Ignored [ 119.301324] P2P interface started [ 119.325632] wl_run_escan: LEGACY_SCAN sync ID: 5, bssidx: 0 [ 121.700426] wl_run_escan: LEGACY_SCAN sync ID: 6, bssidx: 0 [ 124.050310] Connecting with 78:24:af:7a:69:88 ssid "ASUS", len (4) channel=4 [ 124.052682] dhd_dbg_start_pkt_monitor, 1724 [ 124.098424] wl_iw_event: Link UP with 78:24:af:7a:69:88 [ 124.098487] wl_bss_connect_done succeeded with 78:24:af:7a:69:88 [ 124.114115] wl_bss_connect_done succeeded with 78:24:af:7a:69:88 vndr_oui: 00-10-18 [ 145.115460] wl_run_escan: LEGACY_SCAN sync ID: 7, bssidx: 0 [ 188.136326] wl_run_escan: LEGACY_SCAN sync ID: 8, bssidx: 0 [ 192.920267] CFG80211-ERROR) wl_is_linkdown : Link down Reason : WLC_E_DEAUTH_IND [ 192.920315] link down if wlan0 may call cfg80211_disconnected. event : 6, reason=7 from 78:24:af:7a:69:88 [ 192.920328] dhd_dbg_stop_pkt_monitor, 1963 [ 192.922258] wl_iw_event: Link Down with 78:24:af:7a:69:88, reason=2 [ 192.922603] CFG80211-ERROR) wl_cfg80211_tdls_config : No change in tdls state. Do nothing. tdls_enable:1 [ 192.922641] CFG80211-ERROR) wl_is_linkdown : Link down Reason : WLC_E_DEAUTH [ 192.922666] CFG80211-ERROR) wl_cfg80211_tdls_config : No change in tdls state. Do nothing. tdls_enable:1 [ 192.922682] CFG80211-ERROR) wl_is_linkdown : Link down Reason : WLC_E_LINK [ 192.922704] CFG80211-ERROR) wl_cfg80211_tdls_config : No change in tdls state. Do nothing. tdls_enable:1 [ 193.157931] Connecting with 78:24:af:7a:69:88 ssid "ASUS", len (4) channel=4 [ 193.160055] dhd_dbg_start_pkt_monitor, 1724 [ 193.202031] wl_iw_event: Link UP with 78:24:af:7a:69:88 [ 193.202133] wl_bss_connect_done succeeded with 78:24:af:7a:69:88 [ 193.234808] wl_bss_connect_done succeeded with 78:24:af:7a:69:88 vndr_oui: 00-10-18