þ«¯¯«¯­…HELLO! BOOT0 is starting! boot0 commit : 045061a8bb2580cb3fa02e301f52a015040c158f boot0 version : 4.0.0 set pll start set pll end rtc[0] value = 0x00000000 rtc[1] value = 0x00000000 rtc[2] value = 0x00000000 rtc[3] value = 0x00000000 rtc[4] value = 0x00000000 rtc[5] value = 0x00000000 DRAM driver version: V1.1 rsb_send_initseq: rsb clk 400Khz -> 3Mhz PMU: AXP81X ddr voltage = 1500 mv DRAM Type = 3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3) DRAM clk = 672 MHz DRAM zq value: 003b3bbb DRAM single rank full DQ OK DRAM size = 2048 MB DRAM init ok dram size =2048 card boot number = 0, boot0 copy = 0 card no is 0 sdcard 0 line count 4 [mmc]: mmc driver ver 2015-05-08 20:06 [mmc]: sdc0 spd mode error, 2 [mmc]: Wrong media type 0x00000000 [mmc]: ***Try SD card 0*** [mmc]: HSSDR52/SDR25 4 bit [mmc]: 50000000 Hz [mmc]: 7420 MB [mmc]: ***SD/MMC 0 init OK!!!*** sdcard 0 init ok The size of uboot is 000ec000. sum=292a7261 src_sum=292a7261 Succeed in loading uboot from sdmmc flash. boot0: start load other image boot0: Loading BL3-1 Loading file 0 at address 0x40000000,size 0x00008400 success boot0: Loading scp Loading file 2 at address 0x00040000,size 0x00019c00 success set arisc reset to de-assert state Ready to disable icache. Jump to secend Boot. U-Boot 2014.07-00015-g9543266 (Feb 14 2016 - 12:34:44) Allwinner Technology uboot commit : 954326619c99cff30c6ef7c09ac1bbc71158b0dc rsb: secure monitor exist [ 0.337]pmbus: ready [ 0.339][ARISC] :arisc initialize [ 0.670][ARISC] :arisc_dvfs_cfg_vf_table: support only one vf_table [ 0.786][ARISC] :sunxi-arisc driver startup succeeded [ 0.819]PMU: AXP81X [ 0.821]PMU: AXP81X found bat_vol=357, ratio=100 [ 0.827]PMU: dcdc2 1100 [ 0.831]PMU: cpux 1008 Mhz,AXI=336 Mhz PLL6=600 Mhz,AHB1=200 Mhz, APB1=100Mhz AHB2=300Mhz MBus=400Mhz device_type = 3253, onoff=1 dcdc1_vol = 3300, onoff=1 dcdc2_vol = 1100, onoff=1 dcdc6_vol = 1100, onoff=1 aldo1_vol = 2800, onoff=0 aldo2_vol = 1800, onoff=1 aldo3_vol = 3000, onoff=1 dldo1_vol = 3300, onoff=0 dldo2_vol = 3300, onoff=0 dldo3_vol = 2800, onoff=0 dldo4_vol = 3300, onoff=1 eldo1_vol = 1800, onoff=1 eldo2_vol = 1800, onoff=0 eldo3_vol = 1800, onoff=0 fldo1_vol = 1200, onoff=0 fldo2_vol = 1100, onoff=1 gpio0_vol = 3100, onoff=0 vbus not exist no battery, limit to dc run key detect no key found no uart input DRAM: 2 GiB fdt addr: 0xb6ebc0c0 Relocation Offset is: 75f0e000 In: serial Out: serial Err: serial gic: sec monitor mode [ 1.640]start drv_disp_init init_clocks: finish init_clocks. enable power vcc-hdmi-33, ret=0 drv_disp_init finish boot_disp.output_disp=0 boot_disp.output_type=3 boot_disp.output_type=10 fetch script data boot_disp.auto_hpd fail disp0 device type(4) enable attched ok, mgr0<-->device1, type=4, mode=10 plugin [ 2.671]end workmode = 0,storage type = 1 [ 2.675]MMC: 0 [mmc]: mmc driver ver 2015-06-03 13:50:00 SUNXI SD/MMC: 0 [mmc]: start mmc_calibrate_delay_unit, don't access device... [mmc]: delay chain cal done, sample: 200(ps) [mmc]: media type 0x0 [mmc]: Wrong media type 0x0 [mmc]: ************Try SD card 0************ [mmc]: host caps: 0x27 [mmc]: MID 02 PSN 25d6dd72 [mmc]: PNM SA08G -- 0x53-41-30-38-47 [mmc]: PRV 2.2 [mmc]: MDT m-11 y-2015 [mmc]: speed mode : HSSDR52/SDR25 [mmc]: clock : 50000000 Hz [mmc]: bus_width : 4 bit [mmc]: user capacity : 7420 MB [mmc]: ************SD/MMC 0 init OK!!!************ [mmc]: erase_grp_size : 0x1WrBlk*0x200=0x200 Byte [mmc]: secure_feature : 0x0 [mmc]: secure_removal_type : 0x0 [ 2.866]sunxi flash init ok [mmc]: Has init [ 2.901]---drivers/mmc/mmc.c 2733 mmc_init reading uboot.env ** Unable to read "uboot.env" from mmc0:1 ** Using default environment --------fastboot partitions-------- mbr not exist base bootcmd=run mmcbootcmd bootcmd set setargs_mmc key 0 recovery key high 12, low 10 fastboot key high 6, low 4 no misc partition is found to be run cmd=run mmcbootcmd update dtb dram start update dtb dram end serial is: 841051900800500a098b no battery exist sunxi_bmp_logo_display ** Bad device size - sunxi_flash 0 ** sunxi bmp info error : unable to open logo file bootlogo.bmp [ 3.107]inter uboot shell Hit any key to stop autoboot: 3  2  1  0 [mmc]: Has init [ 6.222]---drivers/mmc/mmc.c 2733 mmc_init reading uEnv.txt [mmc]: blkcnt should not be 0 95 bytes read in 6 ms (14.6 KiB/s) Loading boot environment ... [mmc]: Has init [ 6.243]---drivers/mmc/mmc.c 2733 mmc_init reading sun50i-a64-pine64-plus.dtb 69081 bytes read in 9 ms (7.3 MiB/s) [mmc]: Has init [ 6.298]---drivers/mmc/mmc.c 2733 mmc_init reading kernel.img 14284800 bytes read in 706 ms (19.3 MiB/s) 1 Android's image name: Pine64 Kernel load addr 0x41080000 size 12895 KiB RAM disk load addr 0x60000000 size 1051 KiB 2 3 4 5 [ 7.137]ready to boot Starting kernel ... [mmc]: MMC Device 2 not found [mmc]: mmc 2 not find, so not exit [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.10.65-2-pine64-longsleep (longsleep@mose2) (gcc version 5.2.1 20151010 (Ubuntu 5.2.1-22ubuntu1) ) #39 SMP PREEMPT Fri Mar 4 21:55:14 CET 2016 [ 0.000000] CPU: AArch64 Processor [410fd034] revision 4 [ 0.000000] Machine: sun50iw1p1 [ 0.000000] cma: CMA: reserved 64 MiB at 7c000000 [ 0.000000] script_init enter! [ 0.000000] script_init exit! [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] PERCPU: Embedded 12 pages/cpu @ffffffc03af98000 s19776 r8192 d21184 u49152 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 254520 [ 0.000000] Kernel command line: console=tty0 console=ttyS0,115200n8 no_console_suspend earlycon=uart,mmio32,0x01c28000 root=/dev/mmcblk0p2 ro rootwait [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) [ 0.000000] Memory: 1008MB = 1008MB total [ 0.000000] Memory: 935080k/935080k available, 97112k reserved [ 0.000000] Virtual kernel memory layout: [ 0.000000] vmalloc : 0xffffff8000000000 - 0xffffffbbffff0000 (245759 MB) [ 0.000000] vmemmap : 0xffffffbc00e38000 - 0xffffffbc01c00000 ( 13 MB) [ 0.000000] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc03f000000 ( 1008 MB) [ 0.000000] .init : 0xffffffc000b0f000 - 0xffffffc000b8cd40 ( 504 kB) [ 0.000000] .text : 0xffffffc000080000 - 0xffffffc000b0e114 ( 10809 kB) [ 0.000000] .data : 0xffffffc000b8d000 - 0xffffffc000d17900 ( 1579 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] allocated 4194304 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 7.318760] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 7.318793] pid_max: default: 32768 minimum: 301 [ 7.319268] Security Framework initialized [ 7.319312] AppArmor: AppArmor initialized [ 7.319597] Mount-cache hash table entries: 256 [ 7.384202] Initializing cgroup subsys memory [ 7.384438] Initializing cgroup subsys devices [ 7.384459] Initializing cgroup subsys freezer [ 7.384478] Initializing cgroup subsys blkio [ 7.384493] Initializing cgroup subsys perf_event [ 7.384517] Initializing cgroup subsys hugetlb [ 7.384730] ftrace: allocating 26692 entries in 105 pages [ 7.419791] CPU0: update cpu_power 1968128 [ 7.419826] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available [ 7.421340] virtual base = 0xffffff800000a000. [ 7.421365] gicd_base = 0xffffff800000c000. [ 7.421380] gicc_base = 0xffffff800000e000. [ 7.423235] CPU1: Booted secondary processor [ 7.423260] CPU1: update cpu_power 1968128 [ 7.425860] CPU2: Booted secondary processor [ 7.425873] CPU2: update cpu_power 1968128 [ 7.429979] CPU3: Booted secondary processor [ 7.429990] CPU3: update cpu_power 1968128 [ 7.430076] Brought up 4 CPUs [ 7.430163] SMP: Total of 4 processors activated (192.00 BogoMIPS). [ 7.431371] devtmpfs: initialized [ 7.458570] atomic64 test passed [ 7.458596] pinctrl core: initialized pinctrl subsystem [ 7.462634] NET: Registered protocol family 16 [ 7.463099] script_sysfs_init success [ 7.465038] dump_class_init,806, success [ 7.466306] vdso: 2 pages (1 code, 1 data) at base ffffffc000b95000 [ 7.466345] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 7.467606] software IO TLB [mem 0x79c00000-0x7a000000] (4MB) mapped at [ffffffc038c00000-ffffffc038ffffff] [ 7.468840] DMA: preallocated 256 KiB pool for atomic allocations [ 7.469144] Serial: AMBA PL011 UART driver [ 7.470019] axp81x_board_init: axp regl_devs num = 23 [ 7.470368] pll_audio-set_default_rate=24576000 success! [ 7.470406] pll_video0-set_default_rate=297000000 success! [ 7.470517] pll_video1-set_default_rate=297000000 success! [ 7.470628] pll_de-set_default_rate=297000000 success! [ 7.471696] de-set_default_source=pll_de success! [ 7.471713] de-set_default_rate=297000000 success! [ 7.471787] tcon0-set_default_source=pll_mipi success! [ 7.471838] tcon1-set_default_source=pll_video0 success! [ 7.472147] hdmi-set_default_source=pll_video0 success! [ 7.475753] sun50i-r-pinctrl 1f02c00.pinctrl: initialized sunXi PIO driver [ 7.476156] [sun50iw1p1_pinctrl_probe][838] [ 7.478869] sun50i-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver [ 7.481546] sunxi hwspinlock vbase:0xffffff800005c000 [ 7.499606] sunxi_chipid_probe,150: soc bin:0 [ 7.539193] bio: create slab at 0 [ 7.540204] pwm module init! [ 7.545118] SCSI subsystem initialized [ 7.546114] usbcore: registered new interface driver usbfs [ 7.546338] usbcore: registered new interface driver hub [ 7.546614] usbcore: registered new device driver usb [ 7.550457] [ARISC] :sunxi-arisc driver v1.10 [ 7.569940] [ARISC] :sunxi-arisc driver v1.10 startup succeeded [ 7.570615] Advanced Linux Sound Architecture Driver Initialized. [ 7.571970] NetLabel: Initializing [ 7.571987] NetLabel: domain hash size = 128 [ 7.572001] NetLabel: protocols = UNLABELED CIPSOv4 [ 7.572195] NetLabel: unlabeled traffic allowed by default [ 7.572723] [pm]aw_pm_init! [ 7.572808] rtc physical base = 0x0000000001f00000 . [ 7.572858] np name = /soc@01c00000/rtc@01f00000. [ 7.572875] base = ffffff8000070100, len = 4. [ 7.572889] pmu name: pmu0 . [ 7.572936] pmu0_enable = 0x1. [ 7.572950] pmux_id = 0x6. [ 7.572963] pmux_twi_id = 0x1. [ 7.572977] pmux_twi_addr = 0x34. [ 7.572989] pmu name: pmu1 . [ 7.573049] Warning: can not find np for pmu1. [ 7.573293] add_sys_pwr_dm: get ldo name for id: vcc-lpddr failed [ 7.573460] after inited: sys_mask config = 0x4a55. [ 7.573495] Warning: can not find np for dynamic_standby_para. [ 7.573629] [pm]valid [ 7.573639] [pm]valid [ 7.573650] Notice: sun9i&sun8iw5&sun50i not need support normal standby, change to super standby. [ 7.573851] Switching to clocksource arch_sys_counter [ 7.601029] AppArmor: AppArmor Filesystem Enabled [ 7.626172] get det_vbus is fail, 84 [ 7.629516] NET: Registered protocol family 2 [ 7.630896] TCP established hash table entries: 8192 (order: 5, 131072 bytes) [ 7.631072] TCP bind hash table entries: 8192 (order: 5, 131072 bytes) [ 7.631235] TCP: Hash tables configured (established 8192 bind 8192) [ 7.632293] TCP: reno registered [ 7.632312] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 7.632353] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 7.632886] NET: Registered protocol family 1 [ 7.633862] RPC: Registered named UNIX socket transport module. [ 7.633882] RPC: Registered udp transport module. [ 7.633897] RPC: Registered tcp transport module. [ 7.633912] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 7.634768] Unpacking initramfs... [ 7.681446] Freeing initrd memory: 1048K (ffffffc01f000000 - ffffffc01f106000) [ 7.684861] kvm [1]: Using HYP init bounce page @79620000 [ 7.685352] kvm [1]: interrupt-controller@1c84000 IRQ25 [ 7.685834] kvm [1]: timer IRQ27 [ 7.685856] kvm [1]: Hyp mode initialized successfully [ 7.686599] lock super standby defaultly! [ 7.686621] lookup_scene_lock_name: new scene lock super_standby [ 7.686638] scene_lock_init name=super_standby [ 7.686654] scene_lock: super_standby, type 5, count 1 [ 7.687954] audit: initializing netlink socket (disabled) [ 7.688034] type=2000 audit(0.350:1): initialized [ 7.689904] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 7.691027] VFS: Disk quotas dquot_6.5.2 [ 7.691230] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 7.692709] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 7.693991] NFS: Registering the id_resolver key type [ 7.694074] Key type id_resolver registered [ 7.694089] Key type id_legacy registered [ 7.694142] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 7.694999] NTFS driver 2.1.30 [Flags: R/W]. [ 7.695681] fuse init (API version 7.22) [ 7.696630] msgmni has been set to 1956 [ 7.697540] io scheduler noop registered [ 7.697558] io scheduler deadline registered [ 7.697670] io scheduler cfq registered (default) [ 7.699149] [DISP]disp_module_init [ 7.700001] [DISP] boot_disp:0x40a [ 7.700776] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail [ 7.700936] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail [ 7.701093] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail [ 7.702510] [DISP] fb_base:0x47400000 [ 7.710569] [DISP] Fb_map_kernel_logo,line:885:this is not a bmp picture. [ 7.741258] Console: switching to colour frame buffer device 240x67 [ 7.772074] [DISP]disp_module_init finish [ 7.772927] uart0: ttyS0 at MMIO 0x1c28000 (irq = 32) is a SUNXI [ 7.773087] sw_console_setup()1173 - console setup baud 115200 parity n bits 8, flow n [ 8.727394] console [ttyS0] enabled [ 8.732089] uart1: ttyS1 at MMIO 0x1c28400 (irq = 33) is a SUNXI [ 8.739597] misc dump reg init [ 8.743717] [drm] Initialized drm 1.1.0 20060810 [ 8.756247] loop: module loaded [ 8.760032] sunxi-bt bt.27: Missing bt_power. [ 8.764906] sunxi-bt bt.27: bt_power_name ((null)) [ 8.770248] sunxi-bt bt.27: io_regulator_name (vcc-wifi-io) [ 8.776499] sunxi-bt bt.27: bt_rst gpio=356 mul-sel=1 pull=-1 drv_level=-1 data=0 [ 8.785274] sunxi-bt bt.27: clk not config [ 8.790141] sunxi-bt bt.27: block state already is 1 [ 8.796106] sunxi-wlan wlan.26: wlan_busnum (1) [ 8.801155] sunxi-wlan wlan.26: Missing wlan_power. [ 8.806602] sunxi-wlan wlan.26: wlan_power_name ((null)) [ 8.812523] sunxi-wlan wlan.26: io_regulator_name (vcc-wifi-io) [ 8.819157] sunxi-wlan wlan.26: wlan_regon gpio=354 mul-sel=1 pull=-1 drv_level=-1 data=0 [ 8.828692] sunxi-wlan wlan.26: wlan_hostwake gpio=355 mul-sel=6 pull=-1 drv_level=-1 data=0 [ 8.838517] sunxi-wlan wlan.26: clk not config [ 8.844732] tun: Universal TUN/TAP device driver, 1.6 [ 8.850364] tun: (C) 1999-2004 Max Krasnyansky [ 8.858302] WARNING: Get ephy clock is failed [ 8.864659] Failed to alloc md5 [ 8.868176] eth0: Use random mac address [ 8.872851] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.880315] get ehci0-controller drv_vbus_gpio is fail [ 8.886054] get ehci0-controller, regulator_io is no nocare [ 8.892327] [sunxi-ehci0]: probe, pdev->name: 1c1a000.ehci0-controller, sunxi_ehci: 0xffffffc000e0eae0, 0x:ffffff80000a8000, irq_no:68 [ 8.905871] sunxi-ehci 1c1a000.ehci0-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.915983] sunxi-ehci 1c1a000.ehci0-controller: new USB bus registered, assigned bus number 1 [ 8.926125] sunxi-ehci 1c1a000.ehci0-controller: irq 104, io mem 0xffffffc0004c83c4 [ 8.951516] sunxi-ehci 1c1a000.ehci0-controller: USB 0.0 started, EHCI 1.00 [ 8.960348] hub 1-0:1.0: USB hub found [ 8.964565] hub 1-0:1.0: 1 port detected [ 8.969215] scene_lock_init name=ehci_standby [ 8.980298] get ehci1-controller drv_vbus_gpio is fail [ 8.992063] get ehci1-controller, regulator_io is no nocare [ 9.004307] [sunxi-ehci1]: probe, pdev->name: 1c1b000.ehci1-controller, sunxi_ehci: 0xffffffc000e0ed30, 0x:ffffff80000b0000, irq_no:6a [ 9.023935] sunxi-ehci 1c1b000.ehci1-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 9.040266] sunxi-ehci 1c1b000.ehci1-controller: new USB bus registered, assigned bus number 2 [ 9.056578] sunxi-ehci 1c1b000.ehci1-controller: irq 106, io mem 0xffffffc0004c83c4 [ 9.089282] sunxi-ehci 1c1b000.ehci1-controller: USB 0.0 started, EHCI 1.00 [ 9.103304] ehci_irq: highspeed device connect [ 9.115592] hub 2-0:1.0: USB hub found [ 9.126089] hub 2-0:1.0: 1 port detected [ 9.137010] scene_lock_init name=ehci_standby [ 9.148678] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 9.162120] get ohci0-controller drv_vbus_gpio is fail [ 9.174241] get ohci0-controller, regulator_io is no nocare [ 9.186885] [sunxi-ohci0]: probe, pdev->name: 1c1a000.ohci0-controller, sunxi_ohci: 0xffffffc000e0e640 [ 9.203811] sunxi-ohci 1c1a000.ohci0-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 9.220090] sunxi-ohci 1c1a000.ohci0-controller: new USB bus registered, assigned bus number 3 [ 9.236307] sunxi-ohci 1c1a000.ohci0-controller: irq 105, io mem 0x6b61ff726b6b6462 [ 9.310671] hub 3-0:1.0: USB hub found [ 9.321340] hub 3-0:1.0: 1 port detected [ 9.332355] scene_lock_init name=ohci_standby [ 9.343610] get ohci1-controller drv_vbus_gpio is fail [ 9.355770] get ohci1-controller, regulator_io is no nocare [ 9.368264] [sunxi-ohci1]: probe, pdev->name: 1c1b000.ohci1-controller, sunxi_ohci: 0xffffffc000e0e890 [ 9.384913] ehci_irq: highspeed device disconnect [ 9.396568] sunxi-ohci 1c1b000.ohci1-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 9.412679] sunxi-ohci 1c1b000.ohci1-controller: new USB bus registered, assigned bus number 4 [ 9.428720] sunxi-ohci 1c1b000.ohci1-controller: irq 107, io mem 0x6b61ff726b6b6462 [ 9.507464] hub 4-0:1.0: USB hub found [ 9.518018] hub 4-0:1.0: 1 port detected [ 9.528949] scene_lock_init name=ohci_standby [ 9.540757] usbcore: registered new interface driver usb-storage [ 9.553970] usbcore: registered new interface driver ums-alauda [ 9.567025] usbcore: registered new interface driver ums-cypress [ 9.580153] usbcore: registered new interface driver ums-datafab [ 9.593251] usbcore: registered new interface driver ums_eneub6250 [ 9.606456] usbcore: registered new interface driver ums-freecom [ 9.619389] usbcore: registered new interface driver ums-isd200 [ 9.632260] usbcore: registered new interface driver ums-jumpshot [ 9.645229] usbcore: registered new interface driver ums-karma [ 9.657887] usbcore: registered new interface driver ums-onetouch [ 9.670832] usbcore: registered new interface driver ums-realtek [ 9.683620] usbcore: registered new interface driver ums-sddr09 [ 9.696215] usbcore: registered new interface driver ums-sddr55 [ 9.708711] usbcore: registered new interface driver ums-usbat [ 9.721834] mousedev: PS/2 mouse device common for all mice [ 9.734668] input: sunxi-keyboard as /devices/virtual/input/input0 [ 9.748589] sunxi-rtc 1f00000.rtc: rtc core: registered rtc-sunxi as rtc0 [ 9.761914] sunxi-rtc 1f00000.rtc: RTC enabled [ 9.808567] input: axp81x-supplyer as /devices/platform/axp81x_board/axp81x-supplyer.47/input/input1 [ 9.838190] sunxi budget cooling probe start ! [ 9.849112] CPU freq cooling register Success [ 9.859792] CPU hotplug cooling register Success [ 9.871142] CPU budget cooling register Success [ 9.882568] sunxi gpu cooling probe start ! [ 9.893469] CPU gpu cooling register Success [ 9.907080] cpuidle: using governor ladder [ 9.916454] cpuidle: using governor menu [ 9.925709] usb 4-1: new full-speed USB device number 2 using sunxi-ohci [ 9.938877] sunxi-mmc 1c0f000.sdmmc: SD/MMC/SDIO Host Controller Driver(v0.20 2015-7-13 16:28) Compiled in Mar 4 2016 at 21:03:21 [ 9.956913] sunxi-mmc 1c0f000.sdmmc: regulator prop vmmc,str none [ 9.968667] sunxi-mmc 1c0f000.sdmmc: regulator prop vqmmc,str none [ 9.980473] sunxi-mmc 1c0f000.sdmmc: regulator prop vdmmc,str vcc-sdc [ 9.992640] sunxi-mmc 1c0f000.sdmmc: No vmmc regulator found [ 10.003706] sunxi-mmc 1c0f000.sdmmc: No vqmmc regulator found [ 10.015226] sunxi-mmc 1c0f000.sdmmc: Got CD GPIO #166. [ 10.025895] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 10.041656] sunxi-mmc 1c0f000.sdmmc: no vqmmc,Check if there is regulator [ 10.073280] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 10.102841] sunxi-mmc 1c0f000.sdmmc: base:0xffffff80000c4000 irq:92 [ 10.115048] sunxi-mmc 1c10000.sdmmc: SD/MMC/SDIO Host Controller Driver(v0.20 2015-7-13 16:28) Compiled in Mar 4 2016 at 21:03:21 [ 10.133100] sunxi-mmc 1c10000.sdmmc: Can't get vmmc regulator string [ 10.145161] sunxi-mmc 1c10000.sdmmc: Can't get vqmmc regulator string [ 10.157243] sunxi-mmc 1c10000.sdmmc: Can't get vdmmc regulator string [ 10.169264] get() with no identifier [ 10.178126] get() with no identifier [ 10.186871] get() with no identifier [ 10.195457] sunxi-mmc 1c10000.sdmmc: No vmmc regulator found [ 10.206385] sunxi-mmc 1c10000.sdmmc: No vqmmc regulator found [ 10.217362] sunxi-mmc 1c10000.sdmmc: No vdmmc regulator found [ 10.228211] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 52, RTO !! [ 10.240274] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 10.240288] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 52, RTO !! [ 10.240309] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 10.242704] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 10.244831] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 5, RTO !! [ 10.245642] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 5, RTO !! [ 10.246454] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 5, RTO !! [ 10.247266] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 5, RTO !! [ 10.247896] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing LEGACY(SDR12) dt B [ 10.247938] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing LEGACY(SDR12) dt B [ 10.250311] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing LEGACY(SDR12) dt B [ 10.277225] mmc0: host does not support reading read-only switch. assuming write-enable. [ 10.279037] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing SD-HS(SDR25) dt B [ 10.279078] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 50000000Hz bm PP pm ON vdd 16 width 1 timing SD-HS(SDR25) dt B [ 10.279180] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 50000000Hz bm PP pm ON vdd 16 width 4 timing SD-HS(SDR25) dt B [ 10.279201] mmc0: new high speed SDHC card at address 1234 [ 10.462795] sunxi-mmc 1c10000.sdmmc: no vqmmc,Check if there is regulator [ 10.463754] mmcblk0: mmc0:1234 SA08G 7.24 GiB [ 10.486115] mmcblk0: p1 p2 [ 10.496420] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 10.525935] sunxi-mmc 1c10000.sdmmc: base:0xffffff80000cc000 irq:93 [ 10.526735] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 52, RTO !! [ 10.527544] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 52, RTO !! [ 10.527562] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 10.529937] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 10.531754] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 8, RTO !! [ 10.532560] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 10.533367] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 10.534174] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 10.534981] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 10.535790] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 55, RTO !! [ 10.536597] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 55, RTO !! [ 10.537404] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 55, RTO !! [ 10.538211] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 55, RTO !! [ 10.538228] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 10.539061] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 1, RTO !! [ 10.539078] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 0Hz bm OD pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [ 10.748099] input: Logitech USB Receiver as /devices/soc.0/1c1b000.ohci1-controller/usb4/4-1/4-1:1.0/input/input2 [ 10.764811] hid-generic 0003:046D:C52B.0001: input: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-sunxi-ohci-1/input0 [ 10.787584] input: Logitech USB Receiver as /devices/soc.0/1c1b000.ohci1-controller/usb4/4-1/4-1:1.1/input/input3 [ 10.804556] hid-generic 0003:046D:C52B.0002: input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-sunxi-ohci-1/input1 [ 10.829049] hid-generic 0003:046D:C52B.0003: device has no listeners, quitting [ 10.842415] usbcore: registered new interface driver usbhid [ 10.853668] usbhid: USB HID core driver [ 10.890654] sunxi-codec-machine sound.6: codec-aif1 <-> 1c22c00.i2s0-controller mapping ok [ 10.905678] sunxi-codec-machine sound.6: codec-aif2 <-> bb-dai mapping ok [ 10.919066] sunxi-codec-machine sound.6: codec-aif2 <-> bb-dai mapping ok [ 10.932275] sunxi-codec-machine sound.6: codec-aif3 <-> bb-dai mapping ok [ 10.948204] input: audiocodec sunxi Audio Jack as /devices/soc.0/sound.6/sound/card0/input4 [ 10.963530] SUNXI_HMIC_STS:8,225 [ 10.973545] sndhdmi sound.7: sndhdmi <-> 1c22800.daudio mapping ok [ 10.985500] plugout_end:switch:0 [ 10.995864] TCP: cubic registered [ 11.004732] NET: Registered protocol family 10 [ 11.015950] sit: IPv6 over IPv4 tunneling driver [ 11.027189] NET: Registered protocol family 17 [ 11.037356] Key type dns_resolver registered [ 11.047248] Registering SWP/SWPB emulation handler [ 11.059138] [DISP] boot_disp:0x40a [ 11.068854] [HDMI] power vcc-hdmi-33 [ 11.078371] [HDMI] cec support = 0 [ 11.592175] [DISP] disp_device_attached,line:94:attched ok, mgr0<-->device1, type=4 [ 11.606865] sunxi-rtc 1f00000.rtc: setting system clock to 2010-01-01 00:00:08 UTC (1262304008) [ 11.622829] input: sunxi-ths as /devices/virtual/input/input5 [ 11.634691] thermal thermal_zone0: failed to read out thermal zone 0 [ 11.653965] ALSA device list: [ 11.662476] #0: audiocodec [ 11.670823] #1: sndhdmi [ 11.679501] Freeing unused kernel memory: 500K (ffffffc000b0f000 - ffffffc000b8c000) [ 11.716584] [ 11.716584] [ 11.716584] rmmod_host_driver [ 11.716584] [ 11.745909] [ehci0-controller]: sunxi_usb_disable_ehci [ 11.756700] [sunxi-ehci0]: remove, pdev->name: 1c1a000.ehci0-controller, sunxi_ehci: 0xffffffc000e0eae0 [ 11.772286] scene_lock_destroy name=ehci_standby [ 11.782685] sunxi-ehci 1c1a000.ehci0-controller: remove, state 4 [ 11.794585] usb usb1: USB disconnect, device number 1 [ 11.806313] sunxi-ehci 1c1a000.ehci0-controller: USB bus 1 deregistered [ 11.818912] [ohci0-controller]: sunxi_usb_disable_ohci [ 11.829845] [sunxi-ohci0]: remove, pdev->name: 1c1a000.ohci0-controller, sunxi_ohci: 0xffffffc000e0e640 [ 11.845496] scene_lock_destroy name=ohci_standby [ 11.855866] sunxi-ohci 1c1a000.ohci0-controller: remove, state 4 [ 11.867843] usb usb3: USB disconnect, device number 1 [ 11.879620] sunxi-ohci 1c1a000.ohci0-controller: USB bus 3 deregistered [ 11.892376] [ 11.892376] [ 11.892376] insmod_host_driver [ 11.892376] [ 11.922097] [ehci0-controller]: sunxi_usb_enable_ehci [ 11.933139] [sunxi-ehci0]: probe, pdev->name: 1c1a000.ehci0-controller, sunxi_ehci: 0xffffffc000e0eae0, 0x:ffffff80000a8000, irq_no:68 [ 11.952234] sunxi-ehci 1c1a000.ehci0-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 11.968121] sunxi-ehci 1c1a000.ehci0-controller: new USB bus registered, assigned bus number 1 [ 11.984181] sunxi-ehci 1c1a000.ehci0-controller: irq 104, io mem 0xffffffc039968b40 [ 12.011753] sunxi-ehci 1c1a000.ehci0-controller: USB 0.0 started, EHCI 1.00 [ 12.026473] hub 1-0:1.0: USB hub found [ 12.036677] hub 1-0:1.0: 1 port detected [ 12.047184] scene_lock_init name=ehci_standby [ 12.057867] [ohci0-controller]: sunxi_usb_enable_ohci [ 12.069224] [sunxi-ohci0]: probe, pdev->name: 1c1a000.ohci0-controller, sunxi_ohci: 0xffffffc000e0e640 [ 12.085353] sunxi-ohci 1c1a000.ohci0-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 12.100719] sunxi-ohci 1c1a000.ohci0-controller: new USB bus registered, assigned bus number 3 [ 12.115929] sunxi-ohci 1c1a000.ohci0-controller: irq 105, io mem 0xffffffc039968b40 [ 12.193686] hub 3-0:1.0: USB hub found [ 12.203448] hub 3-0:1.0: 1 port detected [ 12.213563] scene_lock_init name=ohci_standby [ 12.223824] host_chose finished 86! [ 12.716043] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities [ 12.731821] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities [ 14.318420] EXT4-fs (mmcblk0p2): recovery complete [ 14.335323] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 14.740597] ip_tables: (C) 2000-2006 Netfilter Core Team [ 14.780421] systemd[1]: systemd 228 running in system mode. (+PAM -AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN) [ 14.807047] systemd[1]: Detected architecture arm64. Welcome to Arch Linux A[ 14.820584] systemd[1]: Set hostname to . RM! [ 15.271803] systemd[1]: Listening on udev Kernel Socket. [ OK [ 15.284366] systemd[1]: Reached target Swap. ] Listening on udev Kernel Socket. [ OK ] Reached targe[ 15.297412] systemd[1]: Listening on Device-mapper event daemon FIFOs. t Swap. [ OK ] [ 15.313346] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. Listening on Device-mapper event daemon FIFOs. [ OK ] [ 15.328878] systemd[1]: Started Forward Password Requests to Wall Directory Watch. Listening on /dev/initctl Compatibility Named Pipe. [ OK ] [ 15.344667] systemd[1]: Listening on LVM2 metadata daemon socket. Started Forward Password Requests to Wall Directory Watch. [ OK ] [ 15.359040] systemd[1]: Reached target Remote File Systems. Listening on LVM2 metadata daemon socket. [ OK ] Reached target Remote File Syste[ 15.376271] systemd[1]: Created slice User and Session Slice. ms. [ OK ] [ 15.390321] systemd[1]: Listening on Network Service Netlink Socket. Created slice User and Session Slice. [ OK ] [ 15.405761] systemd[1]: Created slice System Slice. Listening on Network Service Netlink Socket. [ OK ] [ 15.418819] systemd[1]: Created slice system-systemd\x2dfsck.slice. Created slice System Slice. [ OK ] [ 15.433372] systemd[1]: Created slice system-getty.slice. Created slice system-systemd\x2dfsck.slice. [ OK ] [ 15.446916] systemd[1]: Created slice system-serial\x2dgetty.slice. Created slice system-getty.slice. [ OK ] [ 15.460861] systemd[1]: Listening on udev Control Socket. Created slice system-serial\x2dgetty.slice. [ OK ] [ 15.474144] systemd[1]: Reached target Slices. Listening on udev Control Socket. [ OK ] [ 15.487210] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. Reached target Slices. [ OK ] [ 15.502913] systemd[1]: Reached target Paths. Started Dispatch Password Requests to Console Directory Watch. [ OK ] [ 15.515709] systemd[1]: Listening on Journal Socket. Reached target Paths. [ OK ] Listening on Journal Socket. [ 15.532139] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 15.558031] systemd[1]: Starting Create list of required static device nodes for the current kernel... Starting Create list of required st... nodes for the current kernel... [ 15.605274] systemd[1]: Mounting FUSE Control File System... Mounting FUSE Control File System... [ 15.621536] systemd[1]: Mounting Configuration File System... Mounting Configuration File System... [ 15.638025] systemd[1]: Mounting Huge Pages File System... Mounting Huge Pages File System... [ 15.997739] systemd[1]: Mounting Temporary Directory... [ 15.999807] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) Mounting Temporary Directory... [ 16.025068] systemd[1]: Starting Setup Virtual Console... Starting Setup Virtual Console... [ 16.040816] systemd[1]: Mounting POSIX Message Queue File System... Mounting POSIX Message Queue File System... [ 16.057398] systemd[1]: Starting Apply Kernel Variables... [ 16.070687] systemd[1]: Listening on Journal Socket (/dev/log). Starting Apply Kernel Variables... [ OK ] Listening on Journal Socket (/[ 16.087159] systemd[1]: Starting Journal Service... dev/log). Starting Journal Service... [ 16.102816] systemd[1]: Mounting Debug File System... Mounting Debug File Sys[ 16.114351] systemd[1]: Reached target Encrypted Volumes. tem... [ OK ] Reached target Encrypted Volumes. [ 16.138875] systemd[1]: Mounted Debug File System. [ OK [ 16.150198] systemd[1]: Mounted POSIX Message Queue File System. ] Mounted Debug File System. [ OK ] Mounted POSIX[ 16.164155] systemd[1]: Mounted FUSE Control File System. Message Queue File System. [ OK ] Mounted FUSE [ 16.178792] systemd[1]: Mounted Configuration File System. Control File System. [ OK ] Mounted Confi[ 16.193355] systemd[1]: Mounted Huge Pages File System. guration File System. [ OK ] Mounted Huge [ 16.207605] systemd[1]: Mounted Temporary Directory. Pages File System. [ OK ] Mounted Temporary Directory. [ 16.223175] systemd[1]: Started Remount Root and Kernel File Systems. [ OK ] Started Remount Root and Kernel [ 16.239781] systemd[1]: Started Create list of required static device nodes for the current kernel. File Systems. [ OK ] Started Create list of required [ 16.261665] systemd[1]: Started Setup Virtual Console. sta...ce nodes for the current kernel. [ OK ] Started Setup[ 16.275837] systemd[1]: Started Apply Kernel Variables. Virtual Console. [ OK ] Started Apply Kernel Variables. [ 16.592090] systemd-journald[971]: File /var/log/journal/fa637a105a4f473ca46dbe9bce6405c5/system.journal corrupted or uncleanly shut down, renaming and replacing. [ 16.596143] systemd[1]: Starting udev Coldplug all Devices... Starting udev Coldplug all Devices... [ 16.629859] systemd[1]: Starting Load/Save Random Seed... Starting Load/Save Random Seed... [ 16.646170] systemd[1]: Starting Create Static Device Nodes in /dev... Starting Create Static Device Nodes in /dev... [ 16.673650] systemd[1]: Started Load/Save Random Seed. [ OK ] Started Load/Save Random Seed. [ 16.717566] systemd[1]: Started Create Static Device Nodes in /dev. [ OK ] Started Create Static Device Nodes in /dev. [ 16.737363] systemd[1]: Reached target Local File Systems (Pre). [ OK ] Reached target Local File Syst[ 16.753591] systemd[1]: Starting udev Kernel Device Manager... ems (Pre). Starting udev Kernel Device Manager... [ 16.807937] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. Starting Flush Journal to Persistent Storage... [ 16.882179] systemd-journald[971]: Received request to flush runtime journal from PID 1 [ OK ] Started udev Kernel Device Manager. [ OK ] Started udev Coldplug all Devices. [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Found device /dev/ttyS0. [ 18.179479] Mali: Set gpu frequency to 408 MHz [ 18.190133] Mali: Init Mali gpu clocks successfully [ 18.203000] gpu cooling callback register Success [ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch. [ OK ] Reached target Sound Card. Starti[ 18.223968] Mali: ng Load/Save RF Kill Switch StatMali device driver loaded us... [ 18.235619] ------------[ cut here ]------------ [ 18.235640] WARNING: at drivers/clk/clk.c:781 __clk_disable+0x40/0x78() [ 18.235653] Modules linked in: mali(O+) ss ip_tables x_tables [ 18.235660] CPU: 2 PID: 1696 Comm: alsactl Tainted: G O 3.10.65-2-pine64-longsleep #39 [ 18.235662] Call trace: [ 18.235671] [] dump_backtrace+0x0/0x110 [ 18.235676] [] show_stack+0x20/0x30 [ 18.235683] [] dump_stack+0x1c/0x28 [ 18.235691] [] warn_slowpath_common+0x7c/0xa8 [ 18.235696] [] warn_slowpath_null+0x38/0x4c [ 18.235700] [] __clk_disable+0x3c/0x78 [ 18.235704] [] clk_disable+0x24/0x3c [ 18.235711] [] set_src_function+0x124/0x1bc [ 18.235717] [] snd_ctl_elem_write+0xd0/0x148 [ 18.235720] [] snd_ctl_ioctl+0x3b0/0x708 [ 18.235727] [] vfs_ioctl+0x48/0x6c [ 18.235731] [] do_vfs_ioctl+0x4a4/0x53c [ 18.235735] [] SyS_ioctl+0x64/0x98 [ 18.235737] ---[ end trace fd3337e14c48f86b ]--- [ 18.235741] ------------[ cut here ]------------ [ 18.235746] WARNING: at drivers/clk/clk.c:690 __clk_unprepare+0x34/0x84() [ 18.235752] Modules linked in: mali(O+) ss ip_tables x_tables [ 18.235756] CPU: 2 PID: 1696 Comm: alsactl Tainted: G W O 3.10.65-2-pine64-longsleep #39 [ 18.235757] Call trace: [ 18.235762] [] dump_backtrace+0x0/0x110 [ 18.235766] [] show_stack+0x20/0x30 [ 18.235769] [] dump_stack+0x1c/0x28 [ 18.235774] [] warn_slowpath_common+0x7c/0xa8 [ 18.235779] [] warn_slowpath_null+0x38/0x4c [ 18.235783] [] __clk_unprepare+0x30/0x84 [ 18.235787] [] clk_unprepare+0x20/0x34 [ 18.235791] [] set_src_function+0x12c/0x1bc [ 18.235795] [] snd_ctl_elem_write+0xd0/0x148 [ 18.235799] [] snd_ctl_ioctl+0x3b0/0x708 [ 18.235803] [] vfs_ioctl+0x48/0x6c [ 18.235806] [] do_vfs_ioctl+0x4a4/0x53c [ 18.235810] [] SyS_ioctl+0x64/0x98 [ 18.235812] ---[ end trace fd3337e14c48f86c ]--- [ 18.278807] sunxi-bt bt.27: block state already is 1 [ OK ] Started Load/Save RF Kill Switch Status. [ OK ] Found device /dev/mmcblk0p1. Starting File System Check on /dev/mmcblk0p1... [ OK ] Started File System Check on /dev/mmcblk0p1. Mounting /boot... [ OK ] Mounted /boot. [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... [ OK ] Started Create Volatile Files [ 19.509952] gpu cooling callback set freq limit 0 and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting Login Service... [ OK ] Started D-Bus System Message Bus. Starting Network Service... Starting Permit User Sessions... Starting SSH Key Generation... Starting Save/Restore Sound Card State... [ OK ] Started Entropy Harvesting Daemon. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily verification of password and group files. [ OK ] Started Daily man-db cache up[ 19.846981] ------------[ cut here ]------------ date. [ OK ] Started Daily rotation of log files.[ 19.857112] WARNING: at drivers/clk/clk.c:781 __clk_disable+0x40/0x78() [ OK ] Reached target Timers. [ OK ] Started Permit User Sessions. [ 19.857130] Modules linked in: mali(O) ss ip_tables x_tables [ 19.857137] CPU: 1 PID: 1750 Comm: alsactl Tainted: G W O 3.10.65-2-pine64-longsleep #39 [ 19.857140] Call trace: [ 19.857148] [] dump_backtrace+0x0/0x110 [ 19.857154] [] show_stack+0x20/0x30 [ 19.857160] [] dump_stack+0x1c/0x28 [ 19.857167] [] warn_slowpath_common+0x7c/0xa8 [ 19.857172] [] warn_slowpath_null+0x38/0x4c [ 19.857176] [] __clk_disable+0x3c/0x78 [ 19.857180] [] clk_disable+0x24/0x3c [ 19.857187] [] set_src_function+0x124/0x1bc [ 19.857193] [] snd_ctl_elem_write+0xd0/0x148 [ 19.857197] [] snd_ctl_ioctl+0x3b0/0x708 [ 19.857204] [] vfs_ioctl+0x48/0x6c [ 19.857207] [] do_vfs_ioctl+0x4a4/0x53c [ 19.857211] [] SyS_ioctl+0x64/0x98 [ 19.857214] ---[ end trace fd3337e14c48f86d ]--- [ 19.857289] ------------[ cut here ]------------ [ 19.857296] WARNING: at drivers/clk/clk.c:690 __clk_unprepare+0x34/0x84() [ 19.857302] Modules linked in: mali(O) ss ip_tables x_tables [ 19.857307] CPU: 1 PID: 1750 Comm: alsactl Tainted: G W O 3.10.65-2-pine64-longsleep #39 [ 19.857308] Call trace: [ 19.857313] [] dump_backtrace+0x0/0x110 [ 19.857317] [] show_stack+0x20/0x30 [ 19.857320] [] dump_stack+0x1c/0x28 [ 19.857325] [] warn_slowpath_common+0x7c/0xa8 [ 19.857330] [] warn_slowpath_null+0x38/0x4c [ 19.857334] [] __clk_unprepare+0x30/0x84 [ 19.857338] [] clk_unprepare+0x20/0x34 [ 19.857343] [] set_src_function+0x12c/0x1bc [ 19.857347] [] snd_ctl_elem_write+0xd0/0x148 [ 19.857351] [] snd_ctl_ioctl+0x3b0/0x708 [ 19.857355] [] vfs_ioctl+0x48/0x6c [ 19.857358] [] do_vfs_ioctl+0x4a4/0x53c [ 19.857362] [] SyS_ioctl+0x64/0x98 [ 19.857364] ---[ end trace fd3337e14c48f86e ]--- [ OK ] Started Login Service. [ OK ] Started SSH Key Generation. [ OK ] Started Save/Restore Sound Card State. [ OK ] Started Serial Getty on ttyS0. [ OK ] Started SLiM Simple Login Manager. [ OK ] Started Getty on tty1. [ OK ] Reached target Login Prompts. [ OK ] Started Network Service. [ OK ] Reached target Network. Starting Network Name Resolution... [ OK ] Started OpenSSH Daemon. [ 20.878319] libphy: 1c30000.eth: probed [ 20.887071] sunxi-gmac 1c30000.eth eth0: eth0: PHY ID 001cc915 at 0 IRQ poll (1c30000.eth-0:00) [ OK ] St Arch Linux 3.10.65-2-pine64-longsleep (ttyS0) alarm login: [ 25.797802] libphy: 1c30000.eth-0:00 - Link is Up - 1000/Full [ 45.088968] cgroup: systemd (1) created nested cgroup for controller "blkio" which has incomplete hierarchy support. Nested cgroups may change behavior in the future.