[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.4.174-rockchip64 (root@armbian.com) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11) ) #6 SMP Sun Feb 10 10:43:16 CET 2019
[    0.000000] Boot CPU: AArch64 Processor [410fd034]
[    0.000000] earlycon: Early serial console at MMIO32 0xff1a0000 (options '')
[    0.000000] bootconsole [uart0] enabled
[    0.000000] Reserved memory: failed to reserve memory for node 'drm-logo@00000000': base 0x0000000000000000, size 0 MiB
[    0.000000] On node 0 totalpages: 1015296
[    0.000000]   DMA zone: 15864 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 1015296 pages, LIFO batch:31
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] PERCPU: Embedded 21 pages/cpu @ffffffc0f7edc000 s46312 r8192 d31512 u86016
[    0.000000] pcpu-alloc: s46312 r8192 d31512 u86016 alloc=21*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: enabling workaround for ARM erratum 845719
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 999432
[    0.000000] Kernel command line: earlycon=uart8250,mmio32,0xff1a0000 swiotlb=1 root=UUID=64af660a-d253-4e8d-b02e-fb9519d74328 rootwait rootfstype=ext4 console=ttyS2,1500000 console=tty1 panic=10 consoleblank=0 loglevel=1 ubootpart=52955402-01 usb-storage.quirks=0x2537:0x1066:u,0x2537:0x1068:u   cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.000000] software IO TLB: mapped [mem 0xf7e94000-0xf7ed4000] (0MB)
[    0.000000] Memory: 3964308K/4061184K available (11390K kernel code, 1526K rwdata, 4036K rodata, 1216K init, 712K bss, 96876K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
                   modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
                   vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000   (   246 GB)
                     .init : 0xffffff8008fa0000 - 0xffffff80090d0000   (  1216 KB)
                     .text : 0xffffff8008080000 - 0xffffff8008ba0000   ( 11392 KB)
                   .rodata : 0xffffff8008ba0000 - 0xffffff8008fa0000   (  4096 KB)
                     .data : 0xffffff80090d0000 - 0xffffff800924d808   (  1527 KB)
                   vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000   (     8 GB maximum)
                             0xffffffbdc0008000 - 0xffffffbdc3e00000   (    61 MB actual)
                   fixed   : 0xffffffbffe7fb000 - 0xffffffbffec00000   (  4116 KB)
                   PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000   (    16 MB)
                   memory  : 0xffffffc000200000 - 0xffffffc0f8000000   (  3966 MB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	Build-time adjustment of leaf fanout to 64.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=6.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=6
[    0.000000] NR_IRQS:64 nr_irqs:64 0
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] ITS: /interrupt-controller@fee00000/interrupt-controller@fee20000
[    0.000000] ITS: allocated 65536 Devices @f2d00000 (psz 64K, shr 0)
[    0.000000] ITS: using cache flushing for cmd queue
[    0.000000] GIC: using LPI property table @0x00000000f2c90000
[    0.000000] ITS: Allocated 1792 chunks for LPIs
[    0.000000] CPU0: found redistributor 0 region 0:0x00000000fef00000
[    0.000000] CPU0: using LPI pending table @0x00000000f2ca0000
[    0.000000] GIC: using cache flushing for LPI property table
[    0.000000] GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] }
[    0.000000] GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] }
[    0.000000] rockchip_mmc_get_phase: invalid clk rate
[    0.000000] rockchip_mmc_get_phase: invalid clk rate
[    0.000000] rockchip_mmc_get_phase: invalid clk rate
[    0.000000] rockchip_mmc_get_phase: invalid clk rate
[    0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop0_frac as parent of dclk_vop0, rate changes may not work
[    0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop1_frac as parent of dclk_vop1, rate changes may not work
[    0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.001265] Console: colour dummy device 80x25
[    0.001278] console [tty1] enabled
[    0.001286] bootconsole [uart0] disabled
[    0.001309] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[    0.001322] pid_max: default: 32768 minimum: 301
[    0.001427] Security Framework initialized
[    0.001437] Yama: becoming mindful.
[    0.001458] AppArmor: AppArmor disabled by boot time parameter
[    0.001514] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.001525] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.002249] Initializing cgroup subsys io
[    0.002267] Initializing cgroup subsys memory
[    0.002297] Initializing cgroup subsys devices
[    0.002310] Initializing cgroup subsys freezer
[    0.002323] Initializing cgroup subsys net_cls
[    0.002336] Initializing cgroup subsys perf_event
[    0.002349] Initializing cgroup subsys net_prio
[    0.002365] Initializing cgroup subsys hugetlb
[    0.002375] Initializing cgroup subsys pids
[    0.002416] ftrace: allocating 43611 entries in 171 pages
[    0.106653] sched-energy: Sched-energy-costs installed from DT
[    0.106669] CPU0: update cpu_capacity 401
[    0.106723] ASID allocator initialised with 32768 entries
[    0.107583] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
[    0.107983] Platform MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
[    0.109160] Detected VIPT I-cache on CPU1
[    0.109189] CPU1: found redistributor 1 region 0:0x00000000fef20000
[    0.109214] CPU1: using LPI pending table @0x00000000f2f40000
[    0.109255] CPU1: update cpu_capacity 401
[    0.109259] CPU1: Booted secondary processor [410fd034]
[    0.109829] Detected VIPT I-cache on CPU2
[    0.109850] CPU2: found redistributor 2 region 0:0x00000000fef40000
[    0.109874] CPU2: using LPI pending table @0x00000000f2f60000
[    0.109900] CPU2: update cpu_capacity 401
[    0.109904] CPU2: Booted secondary processor [410fd034]
[    0.110410] Detected VIPT I-cache on CPU3
[    0.110430] CPU3: found redistributor 3 region 0:0x00000000fef60000
[    0.110453] CPU3: using LPI pending table @0x00000000f2fa0000
[    0.110479] CPU3: update cpu_capacity 401
[    0.110483] CPU3: Booted secondary processor [410fd034]
[    0.111006] Detected PIPT I-cache on CPU4
[    0.111030] CPU4: found redistributor 100 region 0:0x00000000fef80000
[    0.111065] CPU4: using LPI pending table @0x00000000f2ff0000
[    0.111100] CPU4: update cpu_capacity 1024
[    0.111104] CPU4: Booted secondary processor [410fd082]
[    0.111643] Detected PIPT I-cache on CPU5
[    0.111662] CPU5: found redistributor 101 region 0:0x00000000fefa0000
[    0.111694] CPU5: using LPI pending table @0x00000000f2420000
[    0.111720] CPU5: update cpu_capacity 1024
[    0.111723] CPU5: Booted secondary processor [410fd082]
[    0.111805] Brought up 6 CPUs
[    0.111888] SMP: Total of 6 processors activated.
[    0.111897] CPU features: detected feature: GIC system register CPU interface
[    0.111910] CPU: All CPU(s) started at EL2
[    0.111953] alternatives: patching kernel code
[    0.113288] devtmpfs: initialized
[    0.128497] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.128520] futex hash table entries: 2048 (order: 5, 131072 bytes)
[    0.129031] xor: measuring software checksum speed
[    0.165700]    8regs     :  2874.000 MB/sec
[    0.205758]    8regs_prefetch:  2578.000 MB/sec
[    0.245815]    32regs    :  3242.000 MB/sec
[    0.285873]    32regs_prefetch:  2864.000 MB/sec
[    0.285880] xor: using function: 32regs (3242.000 MB/sec)
[    0.285905] pinctrl core: initialized pinctrl subsystem
[    0.286136] regulator-dummy: no parameters
[    0.286688] NET: Registered protocol family 16
[    0.299712] cpuidle: using governor ladder
[    0.311737] cpuidle: using governor menu
[    0.311759] Registered FIQ tty driver
[    0.312057] vdso: 2 pages (1 code @ ffffff8008ba6000, 1 data @ ffffff80090d4000)
[    0.312085] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.312889] DMA: preallocated 2048 KiB pool for atomic allocations
[    0.327419] gpiochip_add_data: registered GPIOs 0 to 31 on device: gpio0
[    0.327497] gpiochip_add_data: registered GPIOs 32 to 63 on device: gpio1
[    0.327568] gpiochip_add_data: registered GPIOs 64 to 95 on device: gpio2
[    0.327646] gpiochip_add_data: registered GPIOs 96 to 127 on device: gpio3
[    0.327720] gpiochip_add_data: registered GPIOs 128 to 159 on device: gpio4
[    0.418176] raid6: int64x1  gen()   453 MB/s
[    0.486215] raid6: int64x1  xor()   412 MB/s
[    0.554282] raid6: int64x2  gen()   785 MB/s
[    0.622380] raid6: int64x2  xor()   596 MB/s
[    0.690500] raid6: int64x4  gen()  1109 MB/s
[    0.758568] raid6: int64x4  xor()   669 MB/s
[    0.826702] raid6: int64x8  gen()   862 MB/s
[    0.894779] raid6: int64x8  xor()   634 MB/s
[    0.962879] raid6: neonx1   gen()   911 MB/s
[    1.030959] raid6: neonx1   xor()   660 MB/s
[    1.099098] raid6: neonx2   gen()  1589 MB/s
[    1.167184] raid6: neonx2   xor()  1009 MB/s
[    1.235283] raid6: neonx4   gen()  2076 MB/s
[    1.303359] raid6: neonx4   xor()  1220 MB/s
[    1.371485] raid6: neonx8   gen()  1694 MB/s
[    1.439566] raid6: neonx8   xor()  1279 MB/s
[    1.439572] raid6: using algorithm neonx4 gen() 2076 MB/s
[    1.439578] raid6: .... xor() 1220 MB/s, rmw enabled
[    1.439583] raid6: using intx1 recovery algorithm
[    1.440435] of_get_named_gpiod_flags: parsed 'rockchip,power-ctrl' property of node '/rockchip-suspend[0]' - status (0)
[    1.440472] of_get_named_gpiod_flags: parsed 'rockchip,power-ctrl' property of node '/rockchip-suspend[1]' - status (0)
[    1.440721] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/dc-12v[0]'
[    1.440741] dc_12v: 12000 mV 
[    1.440909] reg-fixed-voltage dc-12v: dc_12v supplying 12000000uV
[    1.441077] of_get_named_gpiod_flags: parsed 'gpio' property of node '/vcc3v3-pcie-regulator[0]' - status (0)
[    1.441122] reg-fixed-voltage vcc3v3-pcie-regulator: Looking up vin-supply from device tree
[    1.441159] vcc3v3_pcie: supplied by dc_12v
[    1.441167] dc_12v: could not add device link regulator.2 err -2
[    1.441207] vcc3v3_pcie: 3300 mV 
[    1.441356] reg-fixed-voltage vcc3v3-pcie-regulator: vcc3v3_pcie supplying 3300000uV
[    1.441409] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/vcc1v8-s0[0]'
[    1.441423] vcc1v8_s0: 1800 mV 
[    1.441578] reg-fixed-voltage vcc1v8-s0: vcc1v8_s0 supplying 1800000uV
[    1.441628] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/vcc-sys[0]'
[    1.441647] reg-fixed-voltage vcc-sys: Looking up vin-supply from device tree
[    1.441681] vcc_sys: supplied by dc_12v
[    1.441689] dc_12v: could not add device link regulator.4 err -2
[    1.441715] vcc_sys: 5000 mV 
[    1.441858] reg-fixed-voltage vcc-sys: vcc_sys supplying 5000000uV
[    1.441904] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/vcc-phy-regulator[0]'
[    1.441918] vcc_phy: no parameters
[    1.442073] reg-fixed-voltage vcc-phy-regulator: vcc_phy supplying 0uV
[    1.442122] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/vcc3v3-sys[0]'
[    1.442138] reg-fixed-voltage vcc3v3-sys: Looking up vin-supply from device tree
[    1.442173] vcc3v3_sys: supplied by vcc_sys
[    1.442180] vcc_sys: could not add device link regulator.6 err -2
[    1.442206] vcc3v3_sys: 3300 mV 
[    1.442347] reg-fixed-voltage vcc3v3-sys: vcc3v3_sys supplying 3300000uV
[    1.442474] of_get_named_gpiod_flags: parsed 'gpio' property of node '/vcc5v0-host-regulator[0]' - status (0)
[    1.442516] vcc5v0_host: no parameters
[    1.442676] reg-fixed-voltage vcc5v0-host-regulator: vcc5v0_host supplying 0uV
[    1.443289] iommu: Adding device ff8f0000.vop to group 0
[    1.443368] platform ff8f0000.vop: iommu /iommu@ff8f3f00 not found
[    1.443374] iommu: Removing device ff8f0000.vop from group 0
[    1.443428] iommu: Adding device ff900000.vop to group 0
[    1.444672] SCSI subsystem initialized
[    1.444836] libata version 3.00 loaded.
[    1.445004] usbcore: registered new interface driver usbfs
[    1.445079] usbcore: registered new interface driver hub
[    1.445157] usbcore: registered new device driver usb
[    1.445242] media: Linux media interface: v0.10
[    1.445279] Linux video capture interface: v2.00
[    1.445385] pps_core: LinuxPPS API ver. 1 registered
[    1.445391] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    1.445411] PTP clock support registered
[    1.446448] Advanced Linux Sound Architecture Driver Initialized.
[    1.447245] NetLabel: Initializing
[    1.447252] NetLabel:  domain hash size = 128
[    1.447257] NetLabel:  protocols = UNLABELED CIPSOv4
[    1.447290] NetLabel:  unlabeled traffic allowed by default
[    1.448012] clocksource: Switched to clocksource arch_sys_counter
[    1.500473] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
[    1.500589] NET: Registered protocol family 2
[    1.501031] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[    1.501251] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes)
[    1.502050] TCP: Hash tables configured (established 32768 bind 32768)
[    1.502164] UDP hash table entries: 2048 (order: 5, 196608 bytes)
[    1.502326] UDP-Lite hash table entries: 2048 (order: 5, 196608 bytes)
[    1.502702] NET: Registered protocol family 1
[    1.502995] RPC: Registered named UNIX socket transport module.
[    1.503003] RPC: Registered udp transport module.
[    1.503008] RPC: Registered tcp transport module.
[    1.503014] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.503030] PCI: CLS 0 bytes, default 64
[    1.503193] Trying to unpack rootfs image as initramfs...
[    1.712980] Freeing initrd memory: 4144K
[    1.713486] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[    1.713571] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
[    1.714592] kvm [1]: 8-bit VMID
[    1.714599] kvm [1]: Hyp mode initialized successfully
[    1.714721] kvm [1]: interrupt-controller@fff20000 IRQ10
[    1.714916] kvm [1]: timer IRQ12
[    1.718031] audit: initializing netlink subsys (disabled)
[    1.718065] audit: type=2000 audit(1.652:1): initialized
[    1.718449] Initialise system trusted keyring
[    1.718793] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    1.726155] VFS: Disk quotas dquot_6.6.0
[    1.726307] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.727696] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.728952] NFS: Registering the id_resolver key type
[    1.728974] Key type id_resolver registered
[    1.728980] Key type id_legacy registered
[    1.728999] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    1.729019] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    1.729671] fuse init (API version 7.23)
[    1.730379] JFS: nTxBlock = 8192, nTxLock = 65536
[    1.735700] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[    1.737393] Key type big_key registered
[    1.737448] 
               TEE Core Framework initialization (ver 1:0.1)
[    1.737473] TEE armv7 Driver initialization
[    1.737855] tz_tee_probe: name="armv7sec", id=0, pdev_name="armv7sec.0"
[    1.737864] TEE core: Alloc the misc device "opteearmtz00" (id=0)
[    1.738047] TEE Core: Register the misc device "opteearmtz00" (id=0,minor=62)
[    1.741940] NET: Registered protocol family 38
[    1.741970] Key type asymmetric registered
[    1.741982] Asymmetric key parser 'x509' registered
[    1.742161] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
[    1.742300] io scheduler noop registered
[    1.742313] io scheduler deadline registered (default)
[    1.742351] io scheduler cfq registered
[    1.743219] phy phy-ff770000.syscon:usb2-phy@e460.0: Looking up phy-supply from device tree
[    1.743304] vcc5v0_host: could not add device link phy-ff770000.syscon:usb2-phy@e460.0 err -2
[    1.743593] phy phy-ff770000.syscon:usb2-phy@e460.1: Looking up phy-supply from device tree
[    1.743604] phy phy-ff770000.syscon:usb2-phy@e460.1: Looking up phy-supply property in node /syscon@ff770000/usb2-phy@e460/otg-port failed
[    1.743810] phy phy-ff770000.syscon:usb2-phy@e460.1: Looking up vbus-supply from device tree
[    1.743820] phy phy-ff770000.syscon:usb2-phy@e460.1: Looking up vbus-supply property in node /syscon@ff770000/usb2-phy@e460/otg-port failed
[    1.743834] phy phy-ff770000.syscon:usb2-phy@e460.1: Failed to get VBUS supply regulator
[    1.744852] phy phy-ff770000.syscon:phy@f780.2: Looking up phy-supply from device tree
[    1.744862] phy phy-ff770000.syscon:phy@f780.2: Looking up phy-supply property in node /syscon@ff770000/phy@f780 failed
[    1.745884] phy phy-ff800000.phy.3: Looking up phy-supply from device tree
[    1.745894] phy phy-ff800000.phy.3: Looking up phy-supply property in node /phy@ff800000/dp-port failed
[    1.745993] phy phy-ff800000.phy.4: Looking up phy-supply from device tree
[    1.746002] phy phy-ff800000.phy.4: Looking up phy-supply property in node /phy@ff800000/usb3-port failed
[    1.746350] phy phy-pcie-phy.5: Looking up phy-supply from device tree
[    1.746360] phy phy-pcie-phy.5: Looking up phy-supply property in node /pcie-phy failed
[    1.748239] rockchip-pcie f8000000.pcie: GPIO lookup for consumer ep
[    1.748250] rockchip-pcie f8000000.pcie: using device tree for GPIO lookup
[    1.748277] of_get_named_gpiod_flags: parsed 'ep-gpios' property of node '/pcie@f8000000[0]' - status (0)
[    1.748514] rockchip-pcie f8000000.pcie: Looking up vpcie3v3-supply from device tree
[    1.748608] rockchip-pcie f8000000.pcie: Looking up vpcie1v8-supply from device tree
[    1.748619] rockchip-pcie f8000000.pcie: Looking up vpcie1v8-supply property in node /pcie@f8000000 failed
[    1.748634] rockchip-pcie f8000000.pcie: no vpcie1v8 regulator found
[    1.748641] rockchip-pcie f8000000.pcie: Looking up vpcie0v9-supply from device tree
[    1.748651] rockchip-pcie f8000000.pcie: Looking up vpcie0v9-supply property in node /pcie@f8000000 failed
[    1.748663] rockchip-pcie f8000000.pcie: no vpcie0v9 regulator found
[    1.772052] rockchip-pcie f8000000.pcie: invalid power supply
[    1.808415] PCI host bridge /pcie@f8000000 ranges:
[    1.808435]   MEM 0xfa000000..0xfbdfffff -> 0xfa000000
[    1.808445]    IO 0xfbe00000..0xfbefffff -> 0xfbe00000
[    1.808738] rockchip-pcie f8000000.pcie: PCI host bridge to bus 0000:00
[    1.808750] pci_bus 0000:00: root bus resource [bus 00-1f]
[    1.808759] pci_bus 0000:00: root bus resource [mem 0xfa000000-0xfbdfffff]
[    1.808770] pci_bus 0000:00: root bus resource [io  0x0000-0xfffff] (bus address [0xfbe00000-0xfbefffff])
[    1.808802] pci 0000:00:00.0: [1d87:0100] type 01 class 0x060400
[    1.808899] pci 0000:00:00.0: supports D1
[    1.808908] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    1.809142] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    1.809261] pci_bus 0000:01: busn_res: can not insert [bus 01-ff] under [bus 00-1f] (conflicts with (null) [bus 00-1f])
[    1.809297] pci 0000:01:00.0: [1b21:0612] type 00 class 0x010601
[    1.809338] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[    1.809347] pci 0000:01:00.0: reg 0x10: [io  size 0x0008]
[    1.809363] pci 0000:01:00.0: reg 0x14: initial BAR value 0x00000000 invalid
[    1.809370] pci 0000:01:00.0: reg 0x14: [io  size 0x0004]
[    1.809385] pci 0000:01:00.0: reg 0x18: initial BAR value 0x00000000 invalid
[    1.809393] pci 0000:01:00.0: reg 0x18: [io  size 0x0008]
[    1.809407] pci 0000:01:00.0: reg 0x1c: initial BAR value 0x00000000 invalid
[    1.809414] pci 0000:01:00.0: reg 0x1c: [io  size 0x0004]
[    1.809429] pci 0000:01:00.0: reg 0x20: initial BAR value 0x00000000 invalid
[    1.809437] pci 0000:01:00.0: reg 0x20: [io  size 0x0020]
[    1.809452] pci 0000:01:00.0: reg 0x24: [mem 0x00000000-0x000001ff]
[    1.809468] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[    1.816047] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    1.816079] pci 0000:00:00.0: BAR 8: assigned [mem 0xfa000000-0xfa0fffff]
[    1.816092] pci 0000:01:00.0: BAR 6: assigned [mem 0xfa000000-0xfa00ffff pref]
[    1.816101] pci 0000:01:00.0: BAR 5: assigned [mem 0xfa010000-0xfa0101ff]
[    1.816113] pci 0000:01:00.0: BAR 4: no space for [io  size 0x0020]
[    1.816121] pci 0000:01:00.0: BAR 4: failed to assign [io  size 0x0020]
[    1.816128] pci 0000:01:00.0: BAR 0: no space for [io  size 0x0008]
[    1.816136] pci 0000:01:00.0: BAR 0: failed to assign [io  size 0x0008]
[    1.816143] pci 0000:01:00.0: BAR 2: no space for [io  size 0x0008]
[    1.816150] pci 0000:01:00.0: BAR 2: failed to assign [io  size 0x0008]
[    1.816158] pci 0000:01:00.0: BAR 1: no space for [io  size 0x0004]
[    1.816165] pci 0000:01:00.0: BAR 1: failed to assign [io  size 0x0004]
[    1.816172] pci 0000:01:00.0: BAR 3: no space for [io  size 0x0004]
[    1.816180] pci 0000:01:00.0: BAR 3: failed to assign [io  size 0x0004]
[    1.816188] pci 0000:00:00.0: PCI bridge to [bus 01]
[    1.816199] pci 0000:00:00.0:   bridge window [mem 0xfa000000-0xfa0fffff]
[    1.816257] pcieport 0000:00:00.0: enabling device (0000 -> 0002)
[    1.816476] pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt
[    1.816484] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
[    1.816496] pcie_pme 0000:00:00.0:pcie01: service driver pcie_pme loaded
[    1.816602] aer 0000:00:00.0:pcie02: service driver aer loaded
[    1.818242] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330
[    1.818253] dma-pl330 ff6d0000.dma-controller: 	DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
[    1.819695] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330
[    1.819706] dma-pl330 ff6e0000.dma-controller: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
[    1.820101] pwm-regulator vdd-log: GPIO lookup for consumer enable
[    1.820110] pwm-regulator vdd-log: using device tree for GPIO lookup
[    1.820119] of_get_named_gpiod_flags: can't parse 'enable-gpios' property of node '/vdd-log[0]'
[    1.820127] of_get_named_gpiod_flags: can't parse 'enable-gpio' property of node '/vdd-log[0]'
[    1.820135] pwm-regulator vdd-log: using lookup tables for GPIO lookup
[    1.820143] pwm-regulator vdd-log: lookup for GPIO enable failed
[    1.820169] pwm-regulator vdd-log: Looking up pwm-supply from device tree
[    1.820236] pwm-regulator: supplied by vcc_sys
[    1.820244] vcc_sys: could not add device link regulator.8 err -2
[    1.820313] vdd_log: 800 <--> 1400 mV at 896 mV 
[    1.820929] Serial: 8250/16550 driver, 5 ports, IRQ sharing disabled
[    1.822648] console [ttyS2] disabled
[    1.822690] ff1a0000.serial: ttyS2 at MMIO 0xff1a0000 (irq = 35, base_baud = 1500000) is a 16550A
[    1.823409] console [ttyS2] enabled
[    1.824486] [drm] Initialized drm 1.1.0 20060810
[    1.827787] [drm] Rockchip DRM driver version: v1.0.1
[    1.828322] usbcore: registered new interface driver udl
[    1.829802] Unable to detect cache hierarchy for CPU 0
[    1.830605] brd: module loaded
[    1.835820] loop: module loaded
[    1.836175] lkdtm: No crash points registered, enable through debugfs
[    1.836613] ahci 0000:01:00.0: version 3.0
[    1.836634] ahci 0000:01:00.0: enabling device (0000 -> 0002)
[    1.836802] ahci 0000:01:00.0: SSS flag set, parallel bus scan disabled
[    1.836858] ahci 0000:01:00.0: AHCI 0001.0200 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
[    1.836870] ahci 0000:01:00.0: flags: 64bit ncq sntf stag led clo pmp pio slum part ccc sxs 
[    1.837940] scsi host0: ahci
[    1.838329] scsi host1: ahci
[    1.838527] ata1: SATA max UDMA/133 abar m512@0xfa010000 port 0xfa010100 irq 225
[    1.838536] ata2: SATA max UDMA/133 abar m512@0xfa010000 port 0xfa010180 irq 225
[    1.839556] rockchip-spi ff1d0000.spi: Failed to request TX DMA channel
[    1.839567] rockchip-spi ff1d0000.spi: Failed to request RX DMA channel
[    1.839574] rockchip-spi ff1d0000.spi: no high_speed pinctrl state
[    1.840165] m25p80 spi32766.0: gd25q128 (16384 Kbytes)
[    1.840190] 3 ofpart partitions found on MTD device spi32766.0
[    1.840197] Creating 3 MTD partitions on "spi32766.0":
[    1.840210] 0x000000000000-0x0000003f8000 : "loader"
[    1.841044] 0x0000003f8000-0x000000400000 : "env"
[    1.841800] 0x0000007c0000-0x000000800000 : "vendor"
[    1.844055] force_sf_dma_mode is ignored if force_thresh_dma_mode is set.
[    1.844071] rk_gmac-dwmac fe300000.ethernet: Looking up phy-supply from device tree
[    1.844148] rk_gmac-dwmac fe300000.ethernet: clock input or output? (input).
[    1.844159] rk_gmac-dwmac fe300000.ethernet: TX delay(0x28).
[    1.844167] rk_gmac-dwmac fe300000.ethernet: RX delay(0x20).
[    1.844191] rk_gmac-dwmac fe300000.ethernet: integrated PHY? (no).
[    1.844378] rk_gmac-dwmac fe300000.ethernet: cannot get clock clk_mac_speed
[    1.844385] rk_gmac-dwmac fe300000.ethernet: clock input from PHY
[    1.849398] rk_gmac-dwmac fe300000.ethernet: init for RGMII
[    1.849519] stmmac - user ID: 0x10, Synopsys ID: 0x35
[    1.849525]  Ring mode enabled
[    1.849530]  DMA HW capability register supported
[    1.849535]  Normal descriptors
[    1.849540]  RX Checksum Offload Engine supported (type 2)
[    1.849545]  Wake-Up On Lan supported
[    1.849584]  Enable RX Mitigation via HW Watchdog Timer
[    1.849682] of_get_named_gpiod_flags: parsed 'snps,reset-gpio' property of node '/ethernet@fe300000[0]' - status (0)
[    1.926412] libphy: stmmac: probed
[    1.926427] eth%d: PHY ID 001cc916 at 0 IRQ POLL (stmmac-0:00) active
[    1.926435] eth%d: PHY ID 001cc916 at 1 IRQ POLL (stmmac-0:01)
[    1.927775] Rockchip WiFi SYS interface (V1.00) ... 
[    1.927859] usbcore: registered new interface driver cdc_ether
[    1.927901] usbcore: registered new interface driver rndis_host
[    1.929253] rockchip-dwc3 usb0: failed to get drvdata dwc3
[    1.933353] rockchip-dwc3 usb1: fail to get drvdata hcd
[    1.934478] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.934489] ehci-pci: EHCI PCI platform driver
[    1.934544] ehci-platform: EHCI generic platform driver
[    1.938377] ehci-platform fe3c0000.usb: EHCI Host Controller
[    1.938548] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 1
[    1.938642] ehci-platform fe3c0000.usb: irq 29, io mem 0xfe3c0000
[    1.948084] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00
[    1.948217] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.948227] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.948236] usb usb1: Product: EHCI Host Controller
[    1.948243] usb usb1: Manufacturer: Linux 4.4.174-rockchip64 ehci_hcd
[    1.948250] usb usb1: SerialNumber: fe3c0000.usb
[    1.948721] hub 1-0:1.0: USB hub found
[    1.948749] hub 1-0:1.0: 1 port detected
[    1.949285] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.949303] ohci-platform: OHCI generic platform driver
[    1.949797] ohci-platform fe3e0000.usb: Generic Platform OHCI controller
[    1.949983] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 2
[    1.950066] ohci-platform fe3e0000.usb: irq 30, io mem 0xfe3e0000
[    2.008171] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    2.008181] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.008189] usb usb2: Product: Generic Platform OHCI controller
[    2.008197] usb usb2: Manufacturer: Linux 4.4.174-rockchip64 ohci_hcd
[    2.008204] usb usb2: SerialNumber: fe3e0000.usb
[    2.008628] hub 2-0:1.0: USB hub found
[    2.008657] hub 2-0:1.0: 1 port detected
[    2.009509] usbcore: registered new interface driver cdc_acm
[    2.009515] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    2.009556] usbcore: registered new interface driver cdc_wdm
[    2.009631] usbcore: registered new interface driver usbserial
[    2.009662] usbcore: registered new interface driver usbserial_generic
[    2.009688] usbserial: USB Serial support registered for generic
[    2.011083] usbcore: registered new interface driver iforce
[    2.011162] usbcore: registered new interface driver xpad
[    2.011536] usbcore: registered new interface driver usbtouchscreen
[    2.011874] .. rk pwm remotectl v1.1 init
[    2.012252] input: ff420030.pwm as /devices/platform/ff420030.pwm/input/input0
[    2.013437] i2c /dev entries driver
[    2.014461] fan53555-regulator 0-0040: GPIO lookup for consumer vsel
[    2.014472] fan53555-regulator 0-0040: using device tree for GPIO lookup
[    2.014511] of_get_named_gpiod_flags: parsed 'vsel-gpios' property of node '/i2c@ff3c0000/syr827@40[0]' - status (0)
[    2.014942] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected!
[    2.014972] fan53555-regulator 0-0040: Looking up vin-supply from device tree
[    2.015050] fan53555-reg: supplied by vcc_sys
[    2.015063] vcc_sys: could not add device link regulator.9 err -2
[    2.016465] vdd_cpu_b: 712 <--> 1500 mV at 1000 mV 
[    2.017164] fan53555-regulator 0-0041: GPIO lookup for consumer vsel
[    2.017174] fan53555-regulator 0-0041: using device tree for GPIO lookup
[    2.017212] of_get_named_gpiod_flags: parsed 'vsel-gpios' property of node '/i2c@ff3c0000/syr828@41[0]' - status (0)
[    2.017603] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected!
[    2.017621] fan53555-regulator 0-0041: Looking up vin-supply from device tree
[    2.017677] fan53555-reg: supplied by vcc_sys
[    2.017689] vcc_sys: could not add device link regulator.10 err -2
[    2.019348] vdd_gpu: 712 <--> 1500 mV at 1000 mV 
[    2.020448] rk808 0-001b: Pmic Chip id: 0x0
[    2.023821] rk808 0-001b: GPIO lookup for consumer dvs
[    2.023832] rk808 0-001b: using device tree for GPIO lookup
[    2.023844] of_get_named_gpiod_flags: can't parse 'dvs-gpios' property of node '/i2c@ff3c0000/pmic@1b[0]'
[    2.023855] of_get_named_gpiod_flags: can't parse 'dvs-gpio' property of node '/i2c@ff3c0000/pmic@1b[0]'
[    2.023865] rk808 0-001b: using lookup tables for GPIO lookup
[    2.023875] rk808 0-001b: lookup for GPIO dvs failed
[    2.023886] rk808-regulator rk808-regulator: there is no dvs0 gpio
[    2.023895] rk808 0-001b: GPIO lookup for consumer dvs
[    2.023905] rk808 0-001b: using device tree for GPIO lookup
[    2.023915] of_get_named_gpiod_flags: can't parse 'dvs-gpios' property of node '/i2c@ff3c0000/pmic@1b[1]'
[    2.023925] of_get_named_gpiod_flags: can't parse 'dvs-gpio' property of node '/i2c@ff3c0000/pmic@1b[1]'
[    2.023934] rk808 0-001b: using lookup tables for GPIO lookup
[    2.023943] rk808 0-001b: lookup for GPIO dvs failed
[    2.023953] rk808-regulator rk808-regulator: there is no dvs1 gpio
[    2.024032] rk808 0-001b: Looking up vcc1-supply from device tree
[    2.024107] DCDC_REG1: supplied by vcc_sys
[    2.024119] vcc_sys: could not add device link regulator.11 err -2
[    2.024579] vdd_center: 900 mV 
[    2.024914] rk808 0-001b: Looking up vcc2-supply from device tree
[    2.024971] DCDC_REG2: supplied by vcc_sys
[    2.024982] vcc_sys: could not add device link regulator.12 err -2
[    2.025282] vdd_cpu_l: 750 <--> 1350 mV at 900 mV 
[    2.025594] rk808 0-001b: Looking up vcc3-supply from device tree
[    2.025645] DCDC_REG3: supplied by vcc_sys
[    2.025656] vcc_sys: could not add device link regulator.13 err -2
[    2.025697] vcc_ddr: at 5000 mV 
[    2.025966] rk808 0-001b: Looking up vcc4-supply from device tree
[    2.026015] DCDC_REG4: supplied by vcc_sys
[    2.026026] vcc_sys: could not add device link regulator.14 err -2
[    2.026232] vcc_1v8: 1800 mV 
[    2.026530] rk808 0-001b: Looking up vcc6-supply from device tree
[    2.026579] LDO_REG1: supplied by vcc_sys
[    2.026590] vcc_sys: could not add device link regulator.15 err -2
[    2.027462] vcc1v8_dvp: 1800 mV 
[    2.027762] rk808 0-001b: Looking up vcc6-supply from device tree
[    2.027814] LDO_REG2: supplied by vcc_sys
[    2.027825] vcc_sys: could not add device link regulator.16 err -2
[    2.028548] vcc3v0_touch: 3000 mV 
[    2.028873] rk808 0-001b: Looking up vcc7-supply from device tree
[    2.028925] LDO_REG3: supplied by vcc_sys
[    2.028935] vcc_sys: could not add device link regulator.17 err -2
[    2.029642] vcc1v8_pmu: 1800 mV 
[    2.029977] rk808 0-001b: Looking up vcc9-supply from device tree
[    2.030028] LDO_REG4: supplied by vcc_sys
[    2.030039] vcc_sys: could not add device link regulator.18 err -2
[    2.030743] vcc_sd: 1800 <--> 3300 mV at 3300 mV 
[    2.031079] rk808 0-001b: Looking up vcc9-supply from device tree
[    2.031130] LDO_REG5: supplied by vcc_sys
[    2.031141] vcc_sys: could not add device link regulator.19 err -2
[    2.031841] vcca3v0_codec: 3000 mV 
[    2.032201] rk808 0-001b: Looking up vcc10-supply from device tree
[    2.032253] LDO_REG6: supplied by vcc_sys
[    2.032263] vcc_sys: could not add device link regulator.20 err -2
[    2.032968] vcc_1v5: 1500 mV 
[    2.033306] rk808 0-001b: Looking up vcc7-supply from device tree
[    2.033358] LDO_REG7: supplied by vcc_sys
[    2.033368] vcc_sys: could not add device link regulator.21 err -2
[    2.034069] vcca1v8_codec: 1800 mV 
[    2.034389] rk808 0-001b: Looking up vcc11-supply from device tree
[    2.034441] LDO_REG8: supplied by vcc_sys
[    2.034452] vcc_sys: could not add device link regulator.22 err -2
[    2.035176] vcc_3v0: 3000 mV 
[    2.035495] rk808 0-001b: Looking up vcc8-supply from device tree
[    2.035548] SWITCH_REG1: supplied by vcc3v3_sys
[    2.035560] vcc3v3_sys: could not add device link regulator.23 err -2
[    2.035624] vcc3v3_s3: at 3300 mV 
[    2.035912] rk808 0-001b: Looking up vcc12-supply from device tree
[    2.035964] SWITCH_REG2: supplied by vcc3v3_sys
[    2.035975] vcc3v3_sys: could not add device link regulator.24 err -2
[    2.036156] vcc3v3_s0: at 3300 mV 
[    2.039768] rk808-rtc rk808-rtc: rtc core: registered rk808-rtc as rtc0
[    2.040244] rk3x-i2c ff3c0000.i2c: Initialized RK3xxx I2C bus at ffffff80093fe000
[    2.041038] rk3x-i2c ff110000.i2c: Initialized RK3xxx I2C bus at ffffff8009cc4000
[    2.042005] fusb302 4-0022: GPIO lookup for consumer int-n
[    2.042016] fusb302 4-0022: using device tree for GPIO lookup
[    2.042055] of_get_named_gpiod_flags: parsed 'int-n-gpios' property of node '/i2c@ff3d0000/fusb30x@22[0]' - status (0)
[    2.042088] fusb302 4-0022: GPIO lookup for consumer vbus-5v
[    2.042098] fusb302 4-0022: using device tree for GPIO lookup
[    2.042131] of_get_named_gpiod_flags: parsed 'vbus-5v-gpios' property of node '/i2c@ff3d0000/fusb30x@22[0]' - status (0)
[    2.042166] fusb302 4-0022: GPIO lookup for consumer vbus-other
[    2.042175] fusb302 4-0022: using device tree for GPIO lookup
[    2.042186] of_get_named_gpiod_flags: can't parse 'vbus-other-gpios' property of node '/i2c@ff3d0000/fusb30x@22[0]'
[    2.042196] of_get_named_gpiod_flags: can't parse 'vbus-other-gpio' property of node '/i2c@ff3d0000/fusb30x@22[0]'
[    2.042206] fusb302 4-0022: using lookup tables for GPIO lookup
[    2.042216] fusb302 4-0022: lookup for GPIO vbus-other failed
[    2.042226] fusb302 4-0022: GPIO lookup for consumer discharge
[    2.042235] fusb302 4-0022: using device tree for GPIO lookup
[    2.042245] of_get_named_gpiod_flags: can't parse 'discharge-gpios' property of node '/i2c@ff3d0000/fusb30x@22[0]'
[    2.042255] of_get_named_gpiod_flags: can't parse 'discharge-gpio' property of node '/i2c@ff3d0000/fusb30x@22[0]'
[    2.042264] fusb302 4-0022: using lookup tables for GPIO lookup
[    2.042273] fusb302 4-0022: lookup for GPIO discharge failed
[    2.042470] fusb302 4-0022: Can't get property of role, set role to default DRP
[    2.050833] fusb302 4-0022: port 0 probe success with role ROLE_MODE_DRP, try_role ROLE_MODE_NONE
[    2.050872] rk3x-i2c ff3d0000.i2c: Initialized RK3xxx I2C bus at ffffff8009cc6000
[    2.051969] IR NEC protocol handler initialized
[    2.051981] IR RC5(x/sz) protocol handler initialized
[    2.051992] IR RC6 protocol handler initialized
[    2.052023] IR JVC protocol handler initialized
[    2.052035] IR Sony protocol handler initialized
[    2.052046] IR SANYO protocol handler initialized
[    2.052057] IR Sharp protocol handler initialized
[    2.052068] IR MCE Keyboard/mouse protocol handler initialized
[    2.052078] IR XMP protocol handler initialized
[    2.052132] usbcore: registered new interface driver redrat3
[    2.052174] usbcore: registered new interface driver iguanair
[    2.052568] usbcore: registered new interface driver uvcvideo
[    2.052573] USB Video Class driver (1.1.1)
[    2.053091] rockchip-iodomain ff320000.syscon:io-domains: Looking up pmu1830-supply from device tree
[    2.053275] rockchip-iodomain ff770000.syscon:io-domains: Looking up bt656-supply from device tree
[    2.053393] rockchip-iodomain ff770000.syscon:io-domains: Looking up audio-supply from device tree
[    2.053459] rockchip-iodomain ff770000.syscon:io-domains: Looking up sdmmc-supply from device tree
[    2.053513] rockchip-iodomain ff770000.syscon:io-domains: Looking up gpio1830-supply from device tree
[    2.055655] rk_tsadcv2_temp_to_code: Invalid conversion table: code=1023, temperature=2147483647
[    2.055800] rockchip-thermal ff260000.tsadc: tsadc is probed successfully!
[    2.056845] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[    2.057368] cpu cpu0: Failed to get leakage
[    2.057394] cpu cpu0: Looking up cpu-supply from device tree
[    2.057461] cpu cpu0: Failed to get pvtm
[    2.057715] cpu cpu4: Failed to get leakage
[    2.057736] cpu cpu4: Looking up cpu-supply from device tree
[    2.057783] cpu cpu4: Failed to get pvtm
[    2.058008] cpu cpu0: Looking up cpu-supply from device tree
[    2.058263] cpu cpu0: Looking up cpu-supply from device tree
[    2.059671] cpu cpu4: Looking up cpu-supply from device tree
[    2.065100] sdhci: Secure Digital Host Controller Interface driver
[    2.065117] sdhci: Copyright(c) Pierre Ossman
[    2.065139] Synopsys Designware Multimedia Card Interface Driver
[    2.067645] dwmmc_rockchip fe320000.dwmmc: IDMAC supports 32-bit address mode.
[    2.067703] dwmmc_rockchip fe320000.dwmmc: Using internal DMA controller.
[    2.067732] dwmmc_rockchip fe320000.dwmmc: Version ID is 270a
[    2.067833] dwmmc_rockchip fe320000.dwmmc: DW MMC controller at irq 25,32 bit host data width,256 deep fifo
[    2.067890] dwmmc_rockchip fe320000.dwmmc: 'clock-freq-min-max' property was deprecated.
[    2.067916] dwmmc_rockchip fe320000.dwmmc: Looking up vmmc-supply from device tree
[    2.067942] dwmmc_rockchip fe320000.dwmmc: Looking up vmmc-supply property in node /dwmmc@fe320000 failed
[    2.068060] dwmmc_rockchip fe320000.dwmmc: Looking up vqmmc-supply from device tree
[    2.068274] dwmmc_rockchip fe320000.dwmmc: No vmmc regulator found
[    2.068322] dwmmc_rockchip fe320000.dwmmc: GPIO lookup for consumer cd
[    2.068341] dwmmc_rockchip fe320000.dwmmc: using device tree for GPIO lookup
[    2.068365] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/dwmmc@fe320000[0]'
[    2.068387] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/dwmmc@fe320000[0]'
[    2.068405] dwmmc_rockchip fe320000.dwmmc: using lookup tables for GPIO lookup
[    2.068426] dwmmc_rockchip fe320000.dwmmc: lookup for GPIO cd failed
[    2.068451] dwmmc_rockchip fe320000.dwmmc: GPIO lookup for consumer wp
[    2.068469] dwmmc_rockchip fe320000.dwmmc: using device tree for GPIO lookup
[    2.068490] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/dwmmc@fe320000[0]'
[    2.068510] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/dwmmc@fe320000[0]'
[    2.068528] dwmmc_rockchip fe320000.dwmmc: using lookup tables for GPIO lookup
[    2.068547] dwmmc_rockchip fe320000.dwmmc: lookup for GPIO wp failed
[    2.068906] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3300000 done
[    2.068934] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3300000 done
[    2.084084] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    2.100155] dwmmc_rockchip fe320000.dwmmc: 1 slots initialized
[    2.101643] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.104413] sdhci-arasan fe330000.sdhci: GPIO lookup for consumer wp
[    2.104426] sdhci-arasan fe330000.sdhci: using device tree for GPIO lookup
[    2.104438] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/sdhci@fe330000[0]'
[    2.104449] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/sdhci@fe330000[0]'
[    2.104458] sdhci-arasan fe330000.sdhci: using lookup tables for GPIO lookup
[    2.104469] sdhci-arasan fe330000.sdhci: lookup for GPIO wp failed
[    2.105588] sdhci-arasan fe330000.sdhci: Looking up vmmc-supply from device tree
[    2.105602] sdhci-arasan fe330000.sdhci: Looking up vmmc-supply property in node /sdhci@fe330000 failed
[    2.105641] sdhci-arasan fe330000.sdhci: Looking up vqmmc-supply from device tree
[    2.105654] sdhci-arasan fe330000.sdhci: Looking up vqmmc-supply property in node /sdhci@fe330000 failed
[    2.105676] sdhci-arasan fe330000.sdhci: No vmmc regulator found
[    2.105685] sdhci-arasan fe330000.sdhci: No vqmmc regulator found
[    2.140307] mmc1: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using ADMA
[    2.142634] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/work-led[0]' - status (0)
[    2.143957] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/diy-led[0]' - status (0)
[    2.144501] hidraw: raw HID events driver (C) Jiri Kosina
[    2.146104] usbcore: registered new interface driver usbhid
[    2.146117] usbhid: USB HID core driver
[    2.146718] ashmem: initialized
[    2.149019] rockchip-saradc ff100000.saradc: Looking up vref-supply from device tree
[    2.149042] rockchip-saradc ff100000.saradc: Looking up vref-supply property in node /saradc@ff100000 failed
[    2.149089] ff100000.saradc supply vref not found, using dummy regulator
[    2.151692] usbcore: registered new interface driver snd-usb-audio
[    2.153171] of_get_named_gpiod_flags: can't parse 'spk-con-gpio' property of node '/i2c@ff110000/es8316@10[0]'
[    2.153190] es8316 1-0010: Can not read property spk_ctl_gpio
[    2.153257] of_get_named_gpiod_flags: parsed 'hp-det-gpio' property of node '/i2c@ff110000/es8316@10[0]' - status (0)
[    2.158394] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3300000 done
[    2.158550] vcc_sd: ramp_delay not set
[    2.158569] rockchip-iodomain ff770000.syscon:io-domains: Setting to 1800000 done
[    2.161384] u32 classifier
[    2.161622] Initializing XFRM netlink socket
[    2.162618] NET: Registered protocol family 10
[    2.163991] [WLAN_RFKILL]: Enter rfkill_wlan_init
[    2.164536] [WLAN_RFKILL]: Enter rfkill_wlan_probe
[    2.164623] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6354
[    2.164634] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[    2.164644] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
[    2.164658] of_get_named_gpiod_flags: can't parse 'WIFI,poweren_gpio' property of node '/wireless-wlan[0]'
[    2.164671] of_get_named_gpiod_flags: can't parse 'WIFI,vbat_gpio' property of node '/wireless-wlan[0]'
[    2.164683] of_get_named_gpiod_flags: can't parse 'WIFI,reset_gpio' property of node '/wireless-wlan[0]'
[    2.164749] of_get_named_gpiod_flags: parsed 'WIFI,host_wake_irq' property of node '/wireless-wlan[0]' - status (0)
[    2.164761] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,host_wake_irq = 3, flags = 0.
[    2.164778] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found !
[    2.164788] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[    2.164801] [WLAN_RFKILL]: Exit rfkill_wlan_probe
[    2.164894] [BT_RFKILL]: Enter rfkill_rk_init
[    2.165550] of_get_named_gpiod_flags: parsed 'uart_rts_gpios' property of node '/wireless-bluetooth[0]' - status (0)
[    2.165563] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 83.
[    2.165579] of_get_named_gpiod_flags: can't parse 'BT,power_gpio' property of node '/wireless-bluetooth[0]'
[    2.165623] of_get_named_gpiod_flags: parsed 'BT,reset_gpio' property of node '/wireless-bluetooth[0]' - status (0)
[    2.165634] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 9.
[    2.165676] of_get_named_gpiod_flags: parsed 'BT,wake_gpio' property of node '/wireless-bluetooth[0]' - status (0)
[    2.165687] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 91.
[    2.165728] of_get_named_gpiod_flags: parsed 'BT,wake_host_irq' property of node '/wireless-bluetooth[0]' - status (0)
[    2.165739] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 4.
[    2.166774] [BT_RFKILL]: Request irq for bt wakeup host
[    2.166866] [BT_RFKILL]: ** disable irq
[    2.167127] [BT_RFKILL]: bt_default device registered.
[    2.167275] Key type dns_resolver registered
[    2.167307] Error: Driver 'ov4689' is already registered, aborting...
[    2.167327] Error: Driver 'ov13850' is already registered, aborting...
[    2.168866] Registered cp15_barrier emulation handler
[    2.169263] Registered setend emulation handler
[    2.172473] registered taskstats version 1
[    2.172508] Loading compiled-in X.509 certificates
[    2.176510] Btrfs loaded, integrity-checker=on
[    2.176655] BTRFS: selftest: Running btrfs free space cache tests
[    2.176703] BTRFS: selftest: Running extent only tests
[    2.176733] BTRFS: selftest: Running bitmap only tests
[    2.176772] BTRFS: selftest: Running bitmap and extent tests
[    2.176819] BTRFS: selftest: Running space stealing from bitmap to extent
[    2.178593] BTRFS: selftest: Free space cache tests finished
[    2.178603] BTRFS: selftest: Running extent buffer operation tests
[    2.178611] BTRFS: selftest: Running btrfs_split_item tests
[    2.178674] BTRFS: selftest: Running find delalloc tests
[    2.186268] mmc_host mmc0: Bus speed (slot 0) = 148500000Hz (slot req 150000000Hz, actual 148500000HZ div = 0)
[    2.459245] dwmmc_rockchip fe320000.dwmmc: Successfully tuned phase to 255
[    2.459299] mmc0: new ultra high speed SDR104 SDHC card at address aaaa
[    2.460733] mmcblk0: mmc0:aaaa SL16G 14.8 GiB 
[    2.464451]  mmcblk0: p1
[    2.601607] BTRFS: selftest: Running btrfs_get_extent tests
[    2.602007] BTRFS: selftest: Running hole first btrfs_get_extent test
[    2.602080] BTRFS: selftest: Running outstanding_extents tests
[    2.602182] BTRFS: selftest: Running qgroup tests
[    2.602195] BTRFS: selftest: Qgroup basic add
[    2.602299] BTRFS: selftest: Qgroup multiple refs test
[    2.641856] Key type encrypted registered
[    2.642868] phy phy-ff770000.syscon:usb2-phy@e450.6: Looking up phy-supply from device tree
[    2.642936] vcc5v0_host: could not add device link phy-ff770000.syscon:usb2-phy@e450.6 err -2
[    2.643157] phy phy-ff770000.syscon:usb2-phy@e450.7: Looking up phy-supply from device tree
[    2.643165] phy phy-ff770000.syscon:usb2-phy@e450.7: Looking up phy-supply property in node /syscon@ff770000/usb2-phy@e450/otg-port failed
[    2.643304] phy phy-ff770000.syscon:usb2-phy@e450.7: Looking up vbus-supply from device tree
[    2.643310] phy phy-ff770000.syscon:usb2-phy@e450.7: Looking up vbus-supply property in node /syscon@ff770000/usb2-phy@e450/otg-port failed
[    2.643323] phy phy-ff770000.syscon:usb2-phy@e450.7: Failed to get VBUS supply regulator
[    2.643815] phy phy-ff7c0000.phy.8: Looking up phy-supply from device tree
[    2.643821] phy phy-ff7c0000.phy.8: Looking up phy-supply property in node /phy@ff7c0000/dp-port failed
[    2.643892] phy phy-ff7c0000.phy.9: Looking up phy-supply from device tree
[    2.643897] phy phy-ff7c0000.phy.9: Looking up phy-supply property in node /phy@ff7c0000/usb3-port failed
[    2.644289] rockchip-drm display-subsystem: devfreq is not set
[    2.644476] rockchip-vop ff900000.vop: missing rockchip,grf property
[    2.644638] rockchip-drm display-subsystem: bound ff900000.vop (ops 0xffffff8008c70018)
[    2.644663] rockchip-vop ff8f0000.vop: missing rockchip,grf property
[    2.644776] rockchip-drm display-subsystem: bound ff8f0000.vop (ops 0xffffff8008c70018)
[    2.645088] i2c i2c-9: of_i2c: modalias failure on /hdmi@ff940000/ports
[    2.645110] dwhdmi-rockchip ff940000.hdmi: registered DesignWare HDMI I2C bus driver
[    2.645176] dwhdmi-rockchip ff940000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
[    2.647612] Registered IR keymap rc-cec
[    2.648463] input: RC for dw_hdmi as /devices/platform/ff940000.hdmi/rc/rc0/input1
[    2.648841] rc0: RC for dw_hdmi as /devices/platform/ff940000.hdmi/rc/rc0
[    2.649122] rockchip-drm display-subsystem: bound ff940000.hdmi (ops 0xffffff8008c66b40)
[    2.649433] i2c i2c-10: of_i2c: modalias failure on /dp@fec00000/ports
[    2.649657] cdn-dp fec00000.dp: Direct firmware load for rockchip/dptx.bin failed with error -2
[    2.649675] rockchip-drm display-subsystem: bound fec00000.dp (ops 0xffffff8008c67ae0)
[    2.649680] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    2.649683] [drm] No driver support for vblank timestamp query.
[    2.649806] rockchip-drm display-subsystem: failed to parse loader memory
[    2.649876] rockchip-drm display-subsystem: No connectors reported connected with modes
[    2.649882] [drm] Cannot find any crtc or sizes - going 1024x768
[    2.657335] Console: switching to colour frame buffer device 128x48
[    2.660911] rockchip-drm display-subsystem: fb0:  frame buffer device
[    2.681576] xhci-hcd xhci-hcd.6.auto: xHCI Host Controller
[    2.682013] xhci-hcd xhci-hcd.6.auto: new USB bus registered, assigned bus number 3
[    2.682193] xhci-hcd xhci-hcd.6.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x02030010
[    2.682286] xhci-hcd xhci-hcd.6.auto: irq 226, io mem 0xfe800000
[    2.682532] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[    2.682549] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.682563] usb usb3: Product: xHCI Host Controller
[    2.682577] usb usb3: Manufacturer: Linux 4.4.174-rockchip64 xhci-hcd
[    2.682590] usb usb3: SerialNumber: xhci-hcd.6.auto
[    2.683406] hub 3-0:1.0: USB hub found
[    2.683460] hub 3-0:1.0: 1 port detected
[    2.683934] xhci-hcd xhci-hcd.6.auto: xHCI Host Controller
[    2.684321] xhci-hcd xhci-hcd.6.auto: new USB bus registered, assigned bus number 4
[    2.684431] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.684614] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[    2.684631] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.684645] usb usb4: Product: xHCI Host Controller
[    2.684658] usb usb4: Manufacturer: Linux 4.4.174-rockchip64 xhci-hcd
[    2.684671] usb usb4: SerialNumber: xhci-hcd.6.auto
[    2.685471] hub 4-0:1.0: USB hub found
[    2.685520] hub 4-0:1.0: 1 port detected
[    2.687714] xhci-hcd xhci-hcd.6.auto: remove, state 1
[    2.687748] usb usb4: USB disconnect, device number 1
[    2.712261] xhci-hcd xhci-hcd.6.auto: Host not halted after 16000 microseconds.
[    2.712282] xhci-hcd xhci-hcd.6.auto: Host controller not halted, aborting reset.
[    2.712336] xhci-hcd xhci-hcd.6.auto: USB bus 4 deregistered
[    2.712932] xhci-hcd xhci-hcd.6.auto: remove, state 1
[    2.712974] usb usb3: USB disconnect, device number 1
[    2.713948] xhci-hcd xhci-hcd.6.auto: USB bus 3 deregistered
[    2.720099] xhci-hcd xhci-hcd.7.auto: xHCI Host Controller
[    2.720391] xhci-hcd xhci-hcd.7.auto: new USB bus registered, assigned bus number 3
[    2.720513] xhci-hcd xhci-hcd.7.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x02030010
[    2.720555] xhci-hcd xhci-hcd.7.auto: irq 227, io mem 0xfe900000
[    2.720678] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[    2.720685] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.720691] usb usb3: Product: xHCI Host Controller
[    2.720697] usb usb3: Manufacturer: Linux 4.4.174-rockchip64 xhci-hcd
[    2.720703] usb usb3: SerialNumber: xhci-hcd.7.auto
[    2.721119] hub 3-0:1.0: USB hub found
[    2.721144] hub 3-0:1.0: 1 port detected
[    2.721366] xhci-hcd xhci-hcd.7.auto: xHCI Host Controller
[    2.721562] xhci-hcd xhci-hcd.7.auto: new USB bus registered, assigned bus number 4
[    2.721611] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.721686] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[    2.721693] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.721699] usb usb4: Product: xHCI Host Controller
[    2.721704] usb usb4: Manufacturer: Linux 4.4.174-rockchip64 xhci-hcd
[    2.721710] usb usb4: SerialNumber: xhci-hcd.7.auto
[    2.722098] hub 4-0:1.0: USB hub found
[    2.722119] hub 4-0:1.0: 1 port detected
[    2.726207] ehci-platform fe380000.usb: EHCI Host Controller
[    2.726399] ehci-platform fe380000.usb: new USB bus registered, assigned bus number 5
[    2.726493] ehci-platform fe380000.usb: irq 27, io mem 0xfe380000
[    2.736081] ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00
[    2.736200] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[    2.736207] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.736214] usb usb5: Product: EHCI Host Controller
[    2.736220] usb usb5: Manufacturer: Linux 4.4.174-rockchip64 ehci_hcd
[    2.736225] usb usb5: SerialNumber: fe380000.usb
[    2.737055] hub 5-0:1.0: USB hub found
[    2.737085] hub 5-0:1.0: 1 port detected
[    2.737843] ohci-platform fe3a0000.usb: Generic Platform OHCI controller
[    2.738249] ohci-platform fe3a0000.usb: new USB bus registered, assigned bus number 6
[    2.738385] ohci-platform fe3a0000.usb: irq 28, io mem 0xfe3a0000
[    2.796582] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[    2.796604] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.796619] usb usb6: Product: Generic Platform OHCI controller
[    2.796633] usb usb6: Manufacturer: Linux 4.4.174-rockchip64 ohci_hcd
[    2.796646] usb usb6: SerialNumber: fe3a0000.usb
[    2.797869] hub 6-0:1.0: USB hub found
[    2.797943] hub 6-0:1.0: 1 port detected
[    2.799232] of_get_named_gpiod_flags: can't parse 'simple-audio-card,hp-det-gpio' property of node '/es8316-sound[0]'
[    2.799248] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpio' property of node '/es8316-sound[0]'
[    2.903647] asoc-simple-card es8316-sound: ES8316 HiFi <-> ff890000.i2s mapping ok
[    2.903704] asoc-simple-card es8316-sound: ASoC: no source widget found for MICBIAS1
[    2.903727] asoc-simple-card es8316-sound: ASoC: Failed to add route MICBIAS1 -> direct -> Mic Jack
[    2.903752] asoc-simple-card es8316-sound: ASoC: no sink widget found for IN1P
[    2.903773] asoc-simple-card es8316-sound: ASoC: Failed to add route Mic Jack -> direct -> IN1P
[    2.904551] es8316 1-0010: ASoC: Failed to create Left Hp mixer debugfs file
[    2.904582] es8316 1-0010: ASoC: Failed to create Right Hp mixer debugfs file
[    2.904669] es8316 1-0010: ASoC: Failed to create HPCP L debugfs file
[    2.904731] es8316 1-0010: ASoC: Failed to create HPCP R debugfs file
[    2.904817] es8316 1-0010: ASoC: Failed to create HPVOL L debugfs file
[    2.904879] es8316 1-0010: ASoC: Failed to create HPVOL R debugfs file
[    2.909242] of_get_named_gpiod_flags: can't parse 'simple-audio-card,hp-det-gpio' property of node '/spdif-sound[0]'
[    2.909270] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpio' property of node '/spdif-sound[0]'
[    2.909815] rockchip-spdif ff870000.spdif: Missing dma channel for stream: 0
[    2.909838] rockchip-spdif ff870000.spdif: ASoC: pcm constructor failed: -22
[    2.909860] asoc-simple-card spdif-sound: ASoC: can't create pcm ff870000.spdif-dit-hifi :-22
[    2.909880] asoc-simple-card spdif-sound: ASoC: failed to instantiate card -22
[    2.910275] asoc-simple-card: probe of spdif-sound failed with error -22
[    2.912797] rk808-rtc rk808-rtc: setting system clock to 2013-01-18 08:50:08 UTC (1358499008)
[    2.912847] of_cfs_init
[    2.912915] of_cfs_init: OK
[    2.938076] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 417; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '', rk_ko_ver is '5', built at '10:42:06', on 'Feb 10 2019'.
[    2.938604] Mali: Mali device driver loaded
[    2.938971] of_get_named_gpiod_flags: parsed 'gpios' property of node '/rockchip-key/power-key[0]' - status (0)
[    2.938998] of_get_named_gpiod_flags: parsed 'gpios' property of node '/rockchip-key/power-key[0]' - status (0)
[    2.939176] input: rk29-keypad as /devices/platform/rockchip-key/input/input2
[    2.940586] ALSA device list:
[    2.940599]   #0: rockchip,es8316-codec
[    3.288364] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    3.311684] ata1.00: ATA-10: WDC WD40EFRX-68N32N0, 82.00A82, max UDMA/133
[    3.311712] ata1.00: 7814037168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    3.313165] ata1.00: configured for UDMA/133
[    3.314709] scsi 0:0:0:0: Direct-Access     ATA      WDC WD40EFRX-68N 0A82 PQ: 0 ANSI: 5
[    3.316451] sd 0:0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB)
[    3.316477] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    3.316769] sd 0:0:0:0: [sda] Write Protect is off
[    3.316793] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    3.316928] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.371738]  sda: sda1
[    3.373902] sd 0:0:0:0: [sda] Attached SCSI disk
[    3.652402] cdn-dp fec00000.dp: Direct firmware load for rockchip/dptx.bin failed with error -2
[    3.808325] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    3.828461] ata2.00: ATA-10: WDC WD40EFRX-68N32N0, 82.00A82, max UDMA/133
[    3.828485] ata2.00: 7814037168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    3.831175] ata2.00: configured for UDMA/133
[    3.832444] scsi 1:0:0:0: Direct-Access     ATA      WDC WD40EFRX-68N 0A82 PQ: 0 ANSI: 5
[    3.833876] sd 1:0:0:0: [sdb] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB)
[    3.833902] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[    3.834311] sd 1:0:0:0: [sdb] Write Protect is off
[    3.834340] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    3.834515] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.892867]  sdb: sdb1
[    3.894970] sd 1:0:0:0: [sdb] Attached SCSI disk
[    3.895948] Freeing unused kernel memory: 1216K
[    3.948287] random: systemd-udevd: uninitialized urandom read (16 bytes read, 60 bits of entropy available)
[    3.948835] random: systemd-udevd: uninitialized urandom read (16 bytes read, 60 bits of entropy available)
[    3.948930] random: systemd-udevd: uninitialized urandom read (16 bytes read, 60 bits of entropy available)
[    3.954150] random: udevadm: uninitialized urandom read (16 bytes read, 60 bits of entropy available)
[    3.954369] random: udevadm: uninitialized urandom read (16 bytes read, 60 bits of entropy available)
[    3.954503] random: udevadm: uninitialized urandom read (16 bytes read, 60 bits of entropy available)
[    3.955043] random: udevadm: uninitialized urandom read (16 bytes read, 60 bits of entropy available)
[    3.955183] random: udevadm: uninitialized urandom read (16 bytes read, 60 bits of entropy available)
[    3.955636] random: udevadm: uninitialized urandom read (16 bytes read, 60 bits of entropy available)
[    3.955775] random: udevadm: uninitialized urandom read (16 bytes read, 60 bits of entropy available)
[    5.386625] random: nonblocking pool is initialized
[    5.656123] cdn-dp fec00000.dp: Direct firmware load for rockchip/dptx.bin failed with error -2
[    9.660149] cdn-dp fec00000.dp: Direct firmware load for rockchip/dptx.bin failed with error -2
[    9.709969] EXT4-fs (mmcblk0p1): mounted filesystem with writeback data mode. Opts: (null)
[    9.966681] systemd[1]: System time before build time, advancing clock.
[    9.977310] ip_tables: (C) 2000-2006 Netfilter Core Team
[    9.989344] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)
[    9.989637] systemd[1]: Detected architecture arm64.
[    9.990650] systemd[1]: Set hostname to <rockpro64>.
[   10.010716] ttyS2 - failed to request DMA, use interrupt mode
[   10.203999] systemd[1]: Created slice System Slice.
[   10.207025] systemd[1]: Mounting Huge Pages File System...
[   10.207963] systemd[1]: Listening on Journal Audit Socket.
[   10.208580] systemd[1]: Reached target Remote File Systems.
[   10.209561] systemd[1]: Created slice system-getty.slice.
[   10.210254] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[   10.210969] systemd[1]: Listening on fsck to fsckd communication Socket.
[   10.213887] systemd[1]: Mounting POSIX Message Queue File System...
[   10.215360] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[   10.216348] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[   10.217047] systemd[1]: Reached target Swap.
[   10.218345] systemd[1]: Created slice User and Session Slice.
[   10.219284] systemd[1]: Listening on udev Kernel Socket.
[   10.219953] systemd[1]: Reached target Slices.
[   10.220667] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[   10.221121] systemd[1]: Reached target Paths.
[   10.221455] systemd[1]: Reached target Encrypted Volumes.
[   10.224287] systemd[1]: Mounting Debug File System...
[   10.225536] systemd[1]: Created slice system-serial\x2dgetty.slice.
[   10.226325] systemd[1]: Listening on Journal Socket (/dev/log).
[   10.227021] systemd[1]: Listening on Journal Socket.
[   10.235167] systemd[1]: Starting Load Kernel Modules...
[   10.238540] systemd[1]: Starting Nameserver information manager...
[   10.243446] systemd[1]: Starting Remount Root and Kernel File Systems...
[   10.247689] systemd[1]: Starting Restore / save the current clock...
[   10.251201] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[   10.255295] systemd[1]: Starting Set the console keyboard layout...
[   10.256165] systemd[1]: Listening on udev Control Socket.
[   10.264570] systemd[1]: Listening on Syslog Socket.
[   10.269989] EXT4-fs (mmcblk0p1): re-mounted. Opts: commit=600,errors=remount-ro
[   10.270766] systemd[1]: Starting Journal Service...
[   10.278788] systemd[1]: Mounted POSIX Message Queue File System.
[   10.283236] systemd[1]: Mounted Debug File System.
[   10.286754] systemd[1]: Mounted Huge Pages File System.
[   10.291121] systemd[1]: Started Load Kernel Modules.
[   10.295421] systemd[1]: Started Remount Root and Kernel File Systems.
[   10.298007] systemd[1]: Started Restore / save the current clock.
[   10.300059] systemd[1]: Started Create list of required static device nodes for the current kernel.
[   10.305039] systemd[1]: Time has been changed
[   10.306823] systemd[1]: Starting Create Static Device Nodes in /dev...
[   10.310112] systemd[1]: Starting Load/Save Random Seed...
[   10.315855] systemd[1]: Starting udev Coldplug all Devices...
[   10.320900] systemd[1]: Mounting FUSE Control File System...
[   10.327677] systemd[1]: Mounting Configuration File System...
[   10.333960] systemd[1]: Starting Apply Kernel Variables...
[   10.346053] systemd[1]: Mounted Configuration File System.
[   10.349502] systemd[1]: Mounted FUSE Control File System.
[   10.354745] systemd[1]: Started Nameserver information manager.
[   10.359864] systemd[1]: Started Load/Save Random Seed.
[   10.365358] systemd[1]: Started Create Static Device Nodes in /dev.
[   10.370737] systemd[1]: Started Apply Kernel Variables.
[   10.389286] systemd[1]: Starting udev Kernel Device Manager...
[   10.476560] systemd[1]: Started udev Kernel Device Manager.
[   10.535139] systemd[1]: Started Set the console keyboard layout.
[   10.538736] systemd[1]: Reached target Local File Systems (Pre).
[   10.548600] systemd[1]: Mounting /tmp...
[   10.560632] systemd[1]: Mounted /tmp.
[   10.565920] systemd[1]: Started Journal Service.
[   10.621985] systemd-journald[310]: Received request to flush runtime journal from PID 1
[   10.747566] rk-hdmi-dp-sound hdmi-dp-sound: control 3:0:0:ELD:0 is already present
[   10.747574] hdmi-audio-codec hdmi-audio-codec.5.auto: ASoC: Failed to add ELD: -16
[   10.748169] rk-hdmi-dp-sound hdmi-dp-sound: multicodec <-> ff8a0000.i2s mapping ok
[   10.748216] hdmi-audio-codec hdmi-audio-codec.5.auto: ASoC: Failed to create Playback debugfs file
[   10.807573] zram: Added device: zram0
[   10.808621] zram: Added device: zram1
[   10.809301] zram: Added device: zram2
[   10.810815] zram: Added device: zram3
[   10.814624] zram: Added device: zram4
[   10.816170] zram: Added device: zram5
[   10.863980] zram1: detected capacity change from 0 to 268435456
[   10.885417] Adding 262140k swap on /dev/zram1.  Priority:5 extents:1 across:262140k SS
[   10.886813] zram2: detected capacity change from 0 to 268435456
[   10.901557] Adding 262140k swap on /dev/zram2.  Priority:5 extents:1 across:262140k SS
[   10.902941] [BT_RFKILL]: bt shut off power
[   10.904300] zram3: detected capacity change from 0 to 268435456
[   10.916355] Adding 262140k swap on /dev/zram3.  Priority:5 extents:1 across:262140k SS
[   10.919172] zram4: detected capacity change from 0 to 268435456
[   10.930232] Adding 262140k swap on /dev/zram4.  Priority:5 extents:1 across:262140k SS
[   10.968796] zram0: detected capacity change from 0 to 52428800
[   10.988727] cfg80211: World regulatory domain updated:
[   10.988735] cfg80211:  DFS Master region: unset
[   10.988738] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   10.988743] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   10.988748] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[   10.988751] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   10.988755] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[   10.988758] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   10.988762] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   10.988765] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   10.988768] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   11.063258] EXT4-fs (zram0): mounted filesystem without journal. Opts: discard
[   12.507312] nr_pdflush_threads exported in /proc is scheduled for removal
[   12.589634] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   12.743041] NET: Registered protocol family 17
[   14.588422] rk_gmac-dwmac fe300000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[   17.667913] cdn-dp fec00000.dp: Direct firmware load for rockchip/dptx.bin failed with error -2
[   33.668203] cdn-dp fec00000.dp: Direct firmware load for rockchip/dptx.bin failed with error -2
[   65.673264] cdn-dp fec00000.dp: Direct firmware load for rockchip/dptx.bin failed with error -2
