HELLO! BOOT0 is starting! boot0 commit : 045061a8bb2580cb3fa02e301f52a015040c158f boot0 version : 4.0.0 set pll start set pll end rtc[0] value = 0x00000000 rtc[1] value = 0x00000000 rtc[2] value = 0x00000000 rtc[3] value = 0x00000000 rtc[4] value = 0x00000000 rtc[5] value = 0x00000000 DRAM driver version: V1.1 rsb_send_initseq: rsb clk 400Khz -> 3Mhz PMU: AXP81X ddr voltage = 1500 mv DRAM Type = 3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3) DRAM clk = 672 MHz DRAM zq value: 003b3bbb DRAM single rank full DQ OK DRAM size = 1024 MB DRAM init ok dram size =1024 card boot number = 0, boot0 copy = 0 card no is 0 sdcard 0 line count 4 [mmc]: mmc driver ver 2015-05-08 20:06 [mmc]: sdc0 spd mode error, 2 [mmc]: Wrong media type 0x00000000 [mmc]: ***Try SD card 0*** [mmc]: HSSDR52/SDR25 4 bit [mmc]: 50000000 Hz [mmc]: 29844 MB [mmc]: ***SD/MMC 0 init OK!!!*** sdcard 0 init ok The size of uboot is 000e8000. sum=1f884ba8 src_sum=1f884ba8 Succeed in loading uboot from sdmmc flash. boot0: start load other image boot0: Loading BL3-1 Loading file 0 at address 0x40000000,size 0x0000a200 success boot0: Loading scp Loading file 2 at address 0x00040000,size 0x00019a00 success set arisc reset to de-assert state Ready to disable icache. ý Configuring SPC Controller NOTICE: BL3-1: v1.0(debug):3cdc5c3 NOTICE: BL3-1: Built : 13:22:57, Aug 10 2018 INFO: BL3-1: Initializing runtime services INFO: BL3-1: Preparing for EL3 exit to normal world INFO: BL3-1: Next image address = 0x4a000000 INFO: BL3-1: Next image spsr = 0x1d3 U-Boot 2014.07 (Aug 23 2018 - 15:16:03) Allwinner Technology uboot commit : 6f37e5cf6a65b0b10455d12dbd631effabe765ec rsb: secure monitor exist [ 0.362]pmbus: ready [ 0.364][ARISC] :arisc initialize [ 0.694][ARISC] :arisc_dvfs_cfg_vf_table: support only one vf_table [SCP] :sunxi-arisc driver begin startup 2 [SCP] :arisc_para size:1a8 [SCP] :arisc version: [v0.1.76] [SCP] :sunxi-arisc driver v1.10 is starting [ 0.822][ARISC] :sunxi-arisc driver startup succeeded [ 0.855]PMU: AXP81X [ 0.858]PMU: AXP81X found bat_vol=258, ratio=100 [ 0.864]PMU: dcdc2 1100 [ 0.867]PMU: cpux 1008 Mhz,AXI=336 Mhz PLL6=600 Mhz,AHB1=200 Mhz, APB1=100Mhz AHB2=300Mhz MBus=400Mhz device_type = 3253, onoff=1 dcdc1_vol = 3300, onoff=1 dcdc2_vol = 1100, onoff=1 dcdc6_vol = 1100, onoff=1 aldo1_vol = 2800, onoff=0 aldo2_vol = 1800, onoff=1 aldo3_vol = 3000, onoff=1 dldo1_vol = 3300, onoff=0 dldo2_vol = 3300, onoff=0 dldo3_vol = 2800, onoff=0 dldo4_vol = 3300, onoff=1 eldo1_vol = 1800, onoff=1 eldo2_vol = 1800, onoff=0 eldo3_vol = 1800, onoff=0 fldo1_vol = 1200, onoff=0 fldo2_vol = 1100, onoff=1 gpio0_vol = 3100, onoff=0 vbus not exist no battery, limit to dc run key detect no key found no uart input DRAM: 1008 MiB fdt addr: 0x76ebcf00 Relocation Offset is: 35f0f000 In: serial Out: serial Err: serial gic: sec monitor mode [ 1.678]start drv_disp_init init_clocks: finish init_clocks. enable power vcc-hdmi-33, ret=0 drv_disp_init finish boot_disp.output_disp=0 boot_disp.output_type=3 boot_disp.output_mode=10 fetch script data boot_disp.auto_hpd fail disp0 device type(4) enable attched ok, mgr0<-->device1, type=4, mode=10 [ 2.047]end workmode = 0,storage type = 1 [ 2.051]MMC: 0 [mmc]: mmc driver ver 2015-06-03 13:50:00 SUNXI SD/MMC: 0 [mmc]: start mmc_calibrate_delay_unit, don't access device... [mmc]: delay chain cal done, sample: 192(ps) [mmc]: media type 0x0 [mmc]: Wrong media type 0x0 [mmc]: ************Try SD card 0************ [mmc]: host caps: 0x27 [mmc]: MID 12 PSN 0000000b [mmc]: PNM SD -- 0x53-44-00-00-00 [mmc]: PRV 0.0 [mmc]: MDT m-8 y-2018 [mmc]: speed mode : HSSDR52/SDR25 [mmc]: clock : 50000000 Hz [mmc]: bus_width : 4 bit [mmc]: user capacity : 29844 MB [mmc]: ************SD/MMC 0 init OK!!!************ [mmc]: erase_grp_size : 0x1WrBlk*0x200=0x200 Byte [mmc]: secure_feature : 0x0 [mmc]: secure_removal_type : 0x0 [ 2.236]sunxi flash init ok ** Unable to use mmc 0:1 for loading the env ** Using default environment --------fastboot partitions-------- mbr not exist base bootcmd=run mmcbootcmd bootcmd set setargs_mmc key 0 recovery key high 12, low 10 fastboot key high 6, low 4 no misc partition is found to be run cmd=run mmcbootcmd update dtb dram start update dtb dram end serial is: 541051900808202203cb check for ANX9807 get Pine64 model from DRAM size DRAM >512M Pine64 model: pine64-plus no battery exist sunxi bmp: unable to open file /boot/bootlogo.bmp [ 2.524]inter uboot shell autoboot in 3 seconds, Press s or to abort 4984 bytes read in 26 ms (186.5 KiB/s) Booting with script ... ## Executing script at 41000000 166 bytes read in 20 ms (7.8 KiB/s) 68724 bytes read in 41 ms (1.6 MiB/s) 4393857 bytes read in 264 ms (15.9 MiB/s) 12636952 bytes read in 679 ms (17.7 MiB/s) Image lacks image_size field, assuming 16MiB ## Loading init Ramdisk from Legacy Image at 45300000 ... Image Name: uInitrd Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 4393793 Bytes = 4.2 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 45000000 Booting using the fdt blob at 0x45000000 reserving fdt memory region: addr=41010000 size=10000 reserving fdt memory region: addr=41020000 size=800 reserving fdt memory region: addr=40100000 size=4000 reserving fdt memory region: addr=40104000 size=1000 reserving fdt memory region: addr=40105000 size=1000 reserving fdt memory region: addr=45000000 size=11000 Loading Ramdisk to 76a85000, end 76eb5b41 ... OK Loading Device Tree to 44feb000, end 44ffefff ... OK Starting kernel ... [mmc]: MMC Device 2 not found [mmc]: mmc 2 not find, so not exit INFO: BL3-1: Next image address = 0x41080000 INFO: BL3-1: Next image spsr = 0x3c9 Loading, please wait... starting version 229 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.27.1 [/sbin/fsck.ext4 (1) -- /dev/mmcblk0p1] fsck.ext4 -a -C0 /dev/mmcblk0p1 /dev/mmcblk0p1: clean, 33471/58368 files, 204843/233472 blocks done. done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. Welcome to Ubuntu 16.04.5 LTS! [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on udev Control Socket. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Created slice System Slice. [ OK ] Listening on Journal Socket. Mounting Debug File System... Starting Set console keymap... Starting Load Kernel Modules... [ OK ] Reached target Swap. [ OK ] Listening on Syslog Socket. Starting Nameserver information manager... [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Encrypted Volumes. [ OK ] Reached target Paths. [ OK ] Listening on fsck to fsckd communication Socket. Starting Remount Root and Kernel File Systems... [ OK ] Created slice User and Session Slice. [ OK ] Reached target Slices. [ OK ] Set up automount Arbitrary Executab...ats File System Automount Point. [ OK ] Started Trigger resolvconf update for networkd DNS. Starting Restore / save the current clock... [ OK ] Created slice system-serial\x2dgetty.slice. [ OK ] Listening on udev Kernel Socket. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. Mounting POSIX Message Queue File System... Mounting Huge Pages File System... Starting Create list of required st... nodes for the current kernel... [ OK ] Mounted Debug File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Huge Pages File System. [ OK ] Started Set console keymap. [ OK ] Started Load Kernel Modules. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Restore / save the current clock. [ OK ] Started Create list of required sta...ce nodes for the current kernel. [ OK ] Started Nameserver information manager. [ OK ] Reached target Network (Pre). Starting Create Static Device Nodes in /dev... Starting Load/Save Random Seed... Starting udev Coldplug all Devices... Mounting Configuration File System... Mounting FUSE Control File System... Starting Apply Kernel Variables... [ OK ] Mounted Configuration File System. [ OK ] Mounted FUSE Control File System. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Load/Save Random Seed. [ OK ] Started Apply Kernel Variables. [ OK ] Reached target Local File Systems (Pre). Mounting /tmp... Starting udev Kernel Device Manager... [ OK ] Mounted /tmp. [ OK ] Started Entropy daemon using the HAVEGE algorithm. Starting Journal Service... [ OK ] Reached target Local File Systems. Starting Set console font and keymap... Starting Raise network interfaces... Starting Armbian ZRAM config... [ OK ] Started udev Coldplug all Devices. [ OK ] Started udev Kernel Device Manager. [ OK ] Started Journal Service. Starting Flush Journal to Persistent Storage... [ OK ] Started Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Started Create Volatile Files and Directories. [ OK ] Reached target System Time Synchronized. Starting Update UTMP about System Boot/Shutdown... [ OK ] Found device /dev/ttyS0. [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch. [ OK ] Reached target Sound Card. Starting Load/Save RF Kill Switch Status... [ OK ] Started Load/Save RF Kill Switch Status. [ OK ] Started Armbian ZRAM config. Starting Armbian memory supported logging... [ OK ] Started Raise network interfaces. [ OK ] Started Armbian memory supported logging. [ OK ] Reached target System Initialization. [ OK ] Started Daily apt download activities. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. Starting Armbian filesystem resize... Starting Armbian hardware optimization... [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Reached target Timers. Starting Armbian hardware monitoring... [ OK ] Started Armbian hardware optimization. [ 14.533091] Call trace: [ 14.762597] Call trace: [FAILED] Failed to start Set console font and keymap. See 'systemctl status console-setup.service' for details. [ OK ] Started Armbian hardware monitoring. [ OK ] Started Armbian filesystem resize. [ OK ] Reached target Basic System. Starting LSB: Load kernel modules needed to enable cpufreq scaling... Starting Login Service... Starting LSB: Start/stop sysstat's sadc... [ OK ] Started D-Bus System Message Bus. Starting Network Manager... Starting Save/Restore Sound Card State... [ OK ] Started Regular background program processing daemon. Starting System Logging Service... [ OK ] Started Armbian first run tasks. [ OK ] Created slice system-getty.slice. Starting Permit User Sessions... [ OK ] Started Permit User Sessions. [ OK ] Started LSB: Start/stop sysstat's sadc. [ OK ] Started System Logging Service. [ OK ] Started LSB: Load kernel modules needed to enable cpufreq scaling. [ OK ] Started Save/Restore Sound Card State. [ OK ] Started Login Service. Starting LSB: set CPUFreq kernel parameters... Starting Set console scheme... [ OK ] Started Set console scheme. [ OK ] Started LSB: set CPUFreq kernel parameters. Starting LSB: Set sysfs variables from /etc/sysfs.conf... [ OK ] Started LSB: Set sysfs variables from /etc/sysfs.conf. [ OK ] Started Network Manager. Starting Network Manager Script Dispatcher Service... [ OK ] Reached target Network. [ OK ] Started Unattended Upgrades Shutdown. Starting OpenBSD Secure Shell server... Starting Network Manager Wait Online... [ OK ] Started Network Manager Script Dispatcher Service. Starting Hostname Service... [ OK ] Started Hostname Service. [ OK ] Started OpenBSD Secure Shell server. Starting Authenticate and Authorize Users to Run Privileged Tasks... [ OK ] Started Authenticate and Authorize Users to Run Privileged Tasks. Stopping OpenBSD Secure Shell server... [ OK ] Stopped OpenBSD Secure Shell server. Starting OpenBSD Secure Shell server... [ OK ] Started OpenBSD Secure Shell server. Stopping OpenBSD Secure Shell server... [ OK ] Stopped OpenBSD Secure Shell server. Starting OpenBSD Secure Shell server... [ OK ] Started OpenBSD Secure Shell server. [FAILED] Failed to start Network Manager Wait Online. See 'systemctl status NetworkManager-wait-online.service' for details. [ OK ] Reached target Network is Online. Starting /etc/rc.local Compatibility... Starting LSB: Advanced IEEE 802.11 management daemon... Starting LSB: Start NTP daemon... [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started LSB: Advanced IEEE 802.11 management daemon. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started LSB: Start NTP daemon. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Ubuntu 16.04.5 LTS pine64 ttyS0 pine64 login: