Hello everybody.
I have just released a new openSUSE image based on the latest BSP kernel (3.10.105)
Full changelog:
- Kernel updated to
3.10.105-0-pine64-longsleep-3
- All software has been updated.
- SoPine images are now available
Also, I have enhanced longsleep's build tools to be able to generate openSUSE images (alongside other improvements). The pull request to longsleep's repository is currently under review but if you want to try it out now, you can view it at my repository (https://github.com/Terra854/build-pine64-image/)
As usual, links are in the first post.
Thanks for
Terra854's work. I can't active the WiFi/Bluetooth module (https://www.pine64.org/?product=wifi-802...4-0-module) with openSUSE revision 28/03/2017 or version 07/12/2016. I tried the following steps.
1. I used the Ubuntu Desktop Image (20161215) with WiFi module, and I can connect to the WiFi. So I think the WiFi module is good.
2. I used the openSUSE image revision 28/03/2017, and followed the steps https://forum.pine64.org/showthread.php?tid=982 without setting the DHCP. After reboot, the WiFi was not automatically connected. The wlan0 appeared after I used the command:
Code:
sudo ip link set wlan0 up
and WiFi signals appeared with the command:
Code:
sudo iwlist wlan0 scan
The I try to active the wlan0 (with some messages) by
Code:
sudo wpa_supplicant -B -iwlan0 -c/etc/wpa_supplicant/wpa_supplicant.conf
Successfully initialized wpa_supplicant
nl80211: Could not re-add multicast membership for vendor events: -2 (No such file or dire
ctory)
The output of ifconfig is:
Code:
eth0 Link encap:Ethernet HWaddr A2:EE:96:E4:54:89
inet addr:192.168.10.245 Bcast:192.168.10.255 Mask:255.255.255.0
inet6 addr: fdd6:752:efa8:0:a0ee:96ff:fee4:5489/64 Scope:Global
inet6 addr: fdd6:752:efa8::b26/64 Scope:Global
inet6 addr: fe80::a0ee:96ff:fee4:5489/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:207 errors:0 dropped:0 overruns:0 frame:0
TX packets:179 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:21407 (20.9 Kb) TX bytes:20570 (20.0 Kb)
Interrupt:114
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:592 errors:0 dropped:0 overruns:0 frame:0
TX packets:592 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:49136 (47.9 Kb) TX bytes:49136 (47.9 Kb)
wlan0 Link encap:Ethernet HWaddr 34:C3:D2:6D:4A:F6
inet6 addr: fe80::36c3:d2ff:fe6d:4af6/64 Scope:Link
inet6 addr: fdd6:752:efa8:0:36c3:d2ff:fe6d:4af6/64 Scope:Global
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:38 errors:0 dropped:0 overruns:0 frame:0
TX packets:10 errors:0 dropped:1 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:12973 (12.6 Kb) TX bytes:1215 (1.1 Kb)
the iwconfig outpus is
Code:
eth0 no wireless extensions.
wlan0 IEEE 802.11bgn ESSID:"mywifi" Nickname:"<WIFI@REALTEK>"
Mode:Managed Frequency:2.462 GHz Access Point: 6C:B0:CE:E9:E9:7F
Bit Rate:150 Mb/s Sensitivity:0/0
Retry:off RTS thr:off Fragment thr:off
Encryption key:****-****-****-****-****-****-****-**** Security mode:open
Power Management:off
Link Quality=100/100 Signal level=-58 dBm Noise level=0 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
dummy0 no wireless extensions.
sit0 no wireless extensions.
lo no wireless extensions.
wlan1 unassociated Nickname:"<WIFI@REALTEK>"
Mode:Managed Frequency=2.412 GHz Access Point: Not-Associated
Sensitivity:0/0
Retry:off RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=0/100 Signal level=0 dBm Noise level=0 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
I still can't connect to the WiFi.
3. I imageed a new openSUSE
revision 28/03/2017, and tried to use yast.
In YaST2 --> System --> Network Settings, I edited the wlan0 (WLAN controller) information and saved. But the details of wlan0 were:
Code:
WLAN controller (Not connected)
MAC : 34:c3:d2:6d:4a:f6
BusID : mmc1:0001:1
It seemed the wlan0 not active and I can't connect to WiFi.
Note that after the command
Code:
sudo wpa_supplicant -B -iwlan0 -c/etc/wpa_supplicant/wpa_supplicant.conf
the wlan0 in the YaST2 changed to
Code:
WLAN controller
MAC : 34:c3:d2:6d:4a:f6
BusID : mmc1:0001:1
I still can't connect to WiFi.
Welcome any comments and suggestions
.
First off, thanks for all your hard work!
I boot up, and log in, but what next?
I'm at pine64@pine64:">
I apologize, but I'm a real newbie.
Dave
it appears the desktop did not start for some reason. try entering
reboot
and see if it starts at next boot
(04-29-2017, 09:19 PM)dkryder Wrote: [ -> ]it appears the desktop did not start for some reason. try entering
reboot
and see if it starts at next boot
There is no desktop environment installed in my images in order to reduce the size of the image.
If you want to install a desktop, you can run the pine64-config tool and select "Install a Desktop Environment", then follow the instructions.
(04-30-2017, 01:31 AM)Terra854 Wrote: [ -> ] (04-29-2017, 09:19 PM)dkryder Wrote: [ -> ]it appears the desktop did not start for some reason. try entering
reboot
and see if it starts at next boot
There is no desktop environment installed in my images in order to reduce the size of the image.
If you want to install a desktop, you can run the pine64-config tool and select "Install a Desktop Environment", then follow the instructions.
yeah, i remember that now. i did the setup process for the image back in november. damn, being old sucks.
try to change directory to usr/local/sbin
cd /usr/local/sbin
and then do
ls -l
and see if those scripts are in that directory , if so try running them again
Thanks.
I changed the directory and now I see pine64-config, but it didn't run. I'm thinking I need to run "sudo ./install.sh" but that didn't work from that directory.
perhaps you need to set permissions on that file to make it executable. right click on file , select permissioms tab, if box to make file executable is unchecked, check it. if it is checked then i'm stumped on what is next.